The driving support ECU assembly receives yaw rate sensor signals from the yaw rate sensor (airbag sensor assembly) and skid control ECU (brake actuator assembly) via CAN communication. If the driving support ECU assembly receives a yaw rate sensor malfunction signal from the yaw rate sensor (airbag sensor assembly) or skid control ECU (brake actuator assembly), DTC C1A46 will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1A46 | Yaw Rate Sensor | ·
While the vehicle is being driven at a speed of 5 km/h (4 mph) or more, the driving support ECU assembly receives a yaw rate sensor malfunction signal from yaw rate sensor for approximately 10 seconds. ·
While the vehicle is being driven at a speed of 5 km/h (4 mph) or more, the driving support ECU assembly receives a yaw rate sensor zero point malfunction signal from skid control ECU (brake actuator assembly) for approximately 10 seconds. |
·
Vehicle stability control system ·
Yaw rate sensor (Airbag sensor assembly) ·
Skid control ECU (Brake actuator assembly) ·
Driving support ECU assembly |
When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.
The pre-collision system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Pre-collision system DTC C1A46 may be stored due to a malfunction in the vehicle stability control system. Therefore, it is necessary to check for and troubleshoot vehicle stability control system DTCs first.
Check for DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Vehicle stability control system DTCs are not output | A |
| Vehicle stability control system DTCs are output | B |
A
B
Clear the DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Drive the vehicle at a speed of 5 km/h (4 mph) or more for 10 seconds or more.
Check for DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A46 is not output | A |
| DTC C1A46 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Replace the driving support ECU assembly.
for LHD: Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU(for LHD)>REMOVAL
for RHD: Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU(for RHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Drive the vehicle at a speed of 5 km/h (4 mph) or more for 10 seconds or more.
Check for DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A46 is not output | A |
| DTC C1A46 is output | B |
A
B
Replace the yaw rate sensor (airbag sensor assembly).
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Drive the vehicle at a speed of 5 km/h (4 mph) or more for 10 seconds or more.
Check for DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A46 is not output | A |
| DTC C1A46 is output | B |
A
B