Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2016.11
RM3160E _58 Vehicle Interior _060169 PRE-COLLISION _0296083 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  C1A50  Brake System Malfunction  


DESCRIPTION

When the pre-collision system is operating, the driving support ECU assembly sends brake control signals to the skid control ECU (brake actuator assembly).

If the driving support ECU assembly receives a vehicle stability control system malfunction signal from the skid control ECU (brake actuator assembly) via CAN communication, DTC C1A50 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A50 Brake System Malfunction While the engine switch is on (IG), the driving support ECU assembly receives a vehicle stability control system malfunction signal from the skid control ECU (brake actuator assembly) for 0.3 seconds or more.
·

Vehicle stability control system

·

Skid control ECU (Brake actuator assembly)

·

Driving support ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

The pre-collision system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)
HINT:

Pre-collision system DTC C1A50 may be stored due to a malfunction in the vehicle stability control system. Therefore, it is necessary to check for and troubleshoot vehicle stability control system DTCs first.


a.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Vehicle stability control system DTCs are not output A
Vehicle stability control system DTCs are output B



A

2.CHECK FOR DTCs (PRE-COLLISION SYSTEM)

B

2.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 0.3 seconds or more.




c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A50 is not output A
DTC C1A50 is output B



A

B

3.REPLACE DRIVING SUPPORT ECU ASSEMBLY
3.REPLACE DRIVING SUPPORT ECU ASSEMBLY

Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
4.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 0.3 seconds or more.




c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A50 is not output A
DTC C1A50 is output B



A

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

B

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)