Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2016.11
RM3160E _58 Vehicle Interior _060169 PRE-COLLISION _0296083 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
U0235 Lost Communication with Cruise Control Front Distance Range Sensor When the engine switch is on (IG), a communication error between the millimeter wave radar sensor assembly and the driving support ECU assembly is detected for approximately 1 second.
·

Millimeter wave radar sensor assembly CAN branch line or connector

·

Millimeter wave radar sensor assembly power source circuit.

·

Millimeter wave radar sensor assembly



WIRING DIAGRAM

B429438E52
0.188,1.833 2.396,2.063 2.208,0.229 10 false No. 5 CAN Junction Connector 0.188,1.667 0.719,1.865 0.531,0.198 10 false F111 1.635,0.771 1.906,0.969 0.271,0.198 10 false 11 1.635,1.354 1.948,1.552 0.313,0.198 10 false 22 5.406,0.76 5.563,0.958 0.156,0.198 10 false 5 5.406,1.354 5.656,1.552 0.25,0.198 10 false 6 5.396,2.604 5.552,2.802 0.156,0.198 10 false 8 5.406,3.365 5.594,3.573 0.188,0.208 10 false 1 5.573,0.875 6.188,1.073 0.615,0.198 10 false CA1P 5.573,1.469 6.188,1.667 0.615,0.198 10 false CA1N 5.583,2.708 6.042,2.906 0.458,0.198 10 false IGB 5.573,3.49 6.188,3.688 0.615,0.198 10 false SGND 1.177,2.708 2.833,2.917 1.656,0.208 10 false from IG1 NO. 3 Relay 5.156,4.031 6.563,4.427 1.406,0.396 10 false Millimeter Wave Radar Sensor Assembly 5.156,3.854 5.615,4.052 0.458,0.198 10 false A81 3.844,2.854 4.656,3.063 0.813,0.208 10 false IG1 NO. 3

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT



HINT:
·

Operating the engine switch, any other switches or a door triggers related ECUs and sensors to communicate using the CAN communication system. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the connectors of ECUs or wire harnesses while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Can Bus Check.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

CAN Bus Check
50007

Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B



A

2.CHECK FOR DTCs (PRE-COLLISION SYSTEM)

B

2.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 1 second or more.




c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U1002 is not output A
DTC U1002 is output B



A

3.CHECK FOR OPEN IN CAN BUS MAIN LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

B

3.CHECK FOR OPEN IN CAN BUS MAIN LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
A380144C26
1.479,0.167 1.875,0.406 0.396,0.24 1.313,1.792 1.448,1.26 true 1.615,1.26 1.823,1.792 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.563,0.198 1.938,0.427 0.375,0.229 10 false A81 1.146,1.813 1.76,2.01 0.615,0.198 10 false CA1P 1.688,1.813 2.302,2.01 0.615,0.198 10 false CA1N
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A81 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A81-5 (CA1P) - A81-6 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



d.

Connect the A81 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)

NG

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)
a.
A380144C25
1.479,0.167 1.875,0.396 0.396,0.229 0.885,0.792 1.406,1.052 true 1.969,1.198 2.573,1.5 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.563,0.198 1.979,0.427 0.417,0.229 10 false A81 0.458,0.708 1.073,0.906 0.615,0.198 10 false SGND 2.625,1.438 3.031,1.646 0.406,0.208 10 false IGB
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A81 millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A81-1 (SGND) - Body ground Always Below 1 Ω



c.

Connect the cable to the negative (-) battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A81-8 (IGB) - Body ground Engine switch on (IG) 11 to 14 V



e.

Connect the A81 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)