| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| U023A | Lost Communication with Front Camera Module | When the engine switch is on (IG), a communication error between the forward recognition camera and driving support ECU is detected for approximately 2 seconds. | ·
Forward recognition camera branch line or connector ·
Forward recognition camera power source circuit ·
Forward recognition camera |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the connectors of ECUs or wire harnesses while performing the inspection below may help determine the cause of the malfunction.
Connect the GTS to the DLC3.
Turn the engine switch to ON.
Turn the GTS on.
Enter the following menus: System Select / Can Bus Check.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| All of the ECUs and sensors that are currently connected to the CAN communication system are displayed | A |
| None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Clear the DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the engine switch on (IG) and wait 2 seconds or more.
Check for DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC U1002 is not output | A |
| DTC U1002 is output | B |
A
B
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
Disconnect the S18 forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S18-6 (CANH) - S18-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Connect the S18 forward recognition camera connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
Disconnect the S18 forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S18-10 (GND) - Body ground | Always | Below 1 Ω |
Connect the cable to the negative (-) battery terminal.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S18-7 (IGB) - Body ground | Engine switch on (IG) | 11 to 14 V |
Connect the S18 forward recognition camera connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG