Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2016.11
RM3160E _58 Vehicle Interior _060169 PRE-COLLISION _0296083 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  U1104  Lost Communication with Driving Support ECU  


DESCRIPTION

The driving support ECU assembly is connected to the millimeter wave radar sensor assembly, forward recognition camera and skid control ECU (brake actuator assembly) via CAN communication. If communication with the millimeter wave radar sensor assembly, forward recognition camera or skid control ECU (brake actuator assembly) stops, the driving support ECU assembly stores DTC U1104.

DTC No. Detection Item DTC Detection Condition Trouble Area
U1104 Lost Communication with Driving Support ECU Any of the following conditions is met:
·

When the engine switch is on (IG), a communication error between the driving support ECU assembly and the millimeter wave radar sensor assembly is detected for approximately 0.2 seconds.

·

When the engine switch is on (IG), a communication error between the driving support ECU assembly and the forward recognition camera is detected for approximately 0.3 seconds.

·

When the engine switch is on (IG), a communication error between the driving support ECU assembly and the skid control ECU (brake actuator assembly) is detected for approximately 1.5 seconds.


·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Forward recognition camera

·

Skid control ECU (Brake actuator assembly)

·

Driving support ECU assembly

·

Wire harness or connector



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

Confirm that the connectors are securely connected, as a partially connected connector can cause this DTC to be stored.



PROCEDURE

1.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U1104 and other DTCs are output A
Only DTC U1104 is output B



A

B

2.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
2.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
Forward recognition camera system DTCs are not output A
Forward recognition camera system DTCs are output B



A

3.CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)

B

3.CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)
a.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Vehicle stability control system DTC are not output A
Vehicle stability control system DTC are output B



A

4.TEST MODE INSPECTION (VEHICLE STABILITY CONTROL SYSTEM)

B

4.TEST MODE INSPECTION (VEHICLE STABILITY CONTROL SYSTEM)
HINT:

When entering test mode, the skid control ECU (brake actuator assembly) communicates with the driving support ECU assembly to judge whether the vehicle is equipped with the pre-collision system. Therefore, do not exit test mode within 5 seconds of entering test mode.


a.

Procedure to enter Test Mode

i.

Turn the engine switch off.


ii.

Check that the steering wheel is centered.


iii.

Apply the parking brake.


iv.

Check that the shift lever is in P.


v.

Connect the GTS to the DLC3.


vi.

Turn the engine switch on (IG).


vii.

Turn the GTS on.


viii.

Switch the skid control ECU (brake actuator assembly) to Test Mode using the GTS. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.

HINT:

Do not exit test mode within 5 seconds of entering test mode. If test mode is exited within 5 seconds of entering test mode, DTC U1104 may be stored. If DTC U1104 is output after exiting test mode, enter test mode again, wait at least 5 seconds, then recheck for DTCs.


Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 4359

ix.

Check that the ABS warning and slip indicator lights come on for several seconds and then blink in the Test Mode pattern.

HINT:

If the ABS warning and slip indicator lights do not blink, inspect the ABS warning and slip indicator light circuits.




b.

End of Test Mode (Signal Check)

i.

End Test Mode (signal check) using the GTS

1.

Turn the engine switch off and enter normal mode.

2.

Remove the GTS.




Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
5.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 1.5 seconds or more.




c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U1104 is not output A
DTC U1104 is output B



A

END

B

6.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
6.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Adjust the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
7.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 1.5 seconds or more.




c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U1104 is not output A
DTC U1104 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

8.REPLACE DRIVING SUPPORT ECU ASSEMBLY
8.REPLACE DRIVING SUPPORT ECU ASSEMBLY

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
9.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 1.5 seconds or more.




c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U1104 is not output A
DTC U1104 is output B



A

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

B

10.REPLACE FORWARD RECOGNITION CAMERA
10.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
11.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 1.5 seconds or more.




c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U1104 is not output A
DTC U1104 is output B



A

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

B

12.REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
12.REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
a.

Replace the skid control ECU (brake actuator assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

END (SKID CONTROL ECU WAS DEFECTIVE)