Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS) › from 2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0296316 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS) J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS)  Distance Control Switch Circuit  


DESCRIPTION

The vehicle-to-vehicle distance control switch is used to set the distance for vehicle-to-vehicle distance control mode. The vehicle-to-vehicle distance control switch is installed in the steering pad switch assembly. The vehicle-to-vehicle distance set value can be changed by operating the steering pad switch assembly (vehicle-to-vehicle distance control switch) while the dynamic radar cruise control system is controlling vehicle speed in vehicle-to-vehicle distance control mode.

WIRING DIAGRAM

A303849E76
1.198,0.99 2.865,1.365 1.667,0.375 10 false Vehicle-to-vehicle Distance Control Switch 0.979,2.667 3.063,3.531 2.083,0.865 10 false Steering Pad Switch Assembly 3.26,2.594 4.333,2.948 1.073,0.354 10 false Spiral Cable Sub-assembly 5.594,2.448 6.063,2.625 0.469,0.177 10 false F128 5.594,2.615 6.615,3.469 1.021,0.854 10 false Driving Support ECU Assembly 2.531,0.719 3.146,0.917 0.615,0.198 10 false DIST 3.375,0.708 3.99,0.906 0.615,0.198 10 false DIST 3.792,0.708 4.406,0.906 0.615,0.198 10 false DIST 2.521,1.885 2.979,2.083 0.458,0.198 10 false ECC 3.385,1.885 3.844,2.083 0.458,0.198 10 false ECC 3.823,1.885 4.281,2.083 0.458,0.198 10 false ECC 3.031,0.844 3.344,1.042 0.313,0.198 10 false z4 3.042,2 3.354,2.198 0.313,0.198 10 false z4 4.229,0.854 4.688,1.052 0.458,0.198 10 false F61 5.74,0.865 6.354,1.063 0.615,0.198 10 false SPSW 5.458,0.719 5.708,0.917 0.25,0.198 10 false 23 4.26,0.594 4.573,0.792 0.313,0.198 10 false 12 4.292,1.76 4.448,1.958 0.156,0.198 10 false 2 3.052,0.594 3.208,0.792 0.156,0.198 10 false 4 3.063,1.75 3.219,1.917 0.156,0.167 10 false 7 4.229,2.01 4.688,2.208 0.458,0.198 10 false F61

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.READ VALUE ON GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Radar Cruise 2 / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Radar Cruise2 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Distance Control Switch Distance control switch signal ON or OFF ON: Distance control switch on
OFF: Distance control switch off
-
Powertrain > Radar Cruise2 > Data List
Tester Display
Distance Control Switch
50003 197 5
OK:

When the steering pad switch assembly (vehicle-to-vehicle distance control switch) is operated, the display changes as shown above.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY AND BODY GROUND)

NG

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY AND BODY GROUND)
a.

Disconnect the F61 spiral cable sub-assembly connector.


b.

Disconnect the F128 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F61-12 (DIST) - F128-23 (SPSW) Always Below 1 Ω
F61-2 (ECC) - Body ground Always Below 1 Ω
F61-12 (DIST) or F128-23 (SPSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR