Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System) › from 2016.11
RM3160E _58 Vehicle Interior _019705 DOOR LOCK _0098501 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System)  Only Wireless Control Function is Inoperative  


DESCRIPTION

The door control receiver receives signals from the door control transmitter module set sub-assembly and sends these signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher signals to the combination meter assembly.

WIRING DIAGRAM

B363624E03
0.302,4.198 1.396,4.375 1.094,0.177 10 false M26 0.302,4.375 1.865,4.604 1.563,0.229 10 false Door Control Receiver 2.469,3.667 2.823,3.865 0.354,0.198 10 false E52 2.479,3.844 3.927,4.177 1.448,0.333 10 false Unlock Warning Switch Assembly 2.625,3.354 2.792,3.521 0.167,0.167 10 false 2 3.583,3.354 3.75,3.521 0.167,0.167 10 false 1 4.156,3.458 4.406,3.625 0.25,0.167 10 false 4D 5.635,3.448 5.917,3.615 0.281,0.167 10 false MB 5.615,2.667 5.896,2.844 0.281,0.177 10 false F19 5.615,1.844 5.917,2.031 0.302,0.188 10 false F19 5.698,3.26 5.948,3.427 0.25,0.167 10 false 3 5.99,3.448 6.406,3.615 0.417,0.167 10 false KSW 5.969,2.667 6.385,2.833 0.417,0.167 10 false PRG 5.979,1.844 6.396,2.01 0.417,0.167 10 false RDA 5.698,2.479 5.906,2.646 0.208,0.167 10 false 5 5.698,1.656 5.906,1.823 0.208,0.167 10 false 4 5.906,4.156 7.063,4.781 1.156,0.625 10 false Main Body ECU (Multiplex Network Body ECU) 1,3.469 1.365,3.635 0.365,0.167 10 false GND 0.979,2.667 1.344,2.833 0.365,0.167 10 false PRG 0.979,1.844 1.344,2.01 0.365,0.167 10 false RDA 1.083,1.031 1.333,1.198 0.25,0.167 10 false +B 1.865,1.198 2.99,1.51 1.125,0.313 10 false MPX-B NO. 1 3.438,1.042 4.271,1.208 0.833,0.167 10 false from Battery 1.396,0.917 1.646,1.25 0.25,0.333 10 false 5 1.396,1.719 1.646,2.052 0.25,0.333 10 false 2 1.406,2.531 1.656,2.865 0.25,0.333 10 false 3 4.167,3.26 4.417,3.427 0.25,0.167 10 false 28 4.208,3.875 5.813,4.323 1.604,0.448 10 false Instrument Panel Junction Block Assembly 1.396,3.313 1.646,3.646 0.25,0.333 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, wireless function performance may be affected.

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

Check the power door lock operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Locked doors unlock.



Result:
Proceed to
OK
NG



OK

2.CHECK KEY REMINDER WARNING SYSTEM

NG

2.CHECK KEY REMINDER WARNING SYSTEM
a.

Check that the key reminder warning buzzer operates properly.

Click hereVehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>OPERATION CHECK

OK:

Key reminder warning buzzer operates properly.



Result:
Proceed to
OK
NG



OK

3.CHECK DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY

NG

3.CHECK DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY
a.

When a known good registered door control transmitter module set sub-assembly is used, check that the wireless functions operate properly.


Result:
Result Proceed to
Wireless door lock/unlock function operates properly with a known good door control transmitter module set sub-assembly A
Wireless door lock/unlock function does not operate B



A

4.CHECK TRANSMITTER BATTERY (VOLTAGE)

B

5.CHECK WAVE ENVIRONMENT
4.CHECK TRANSMITTER BATTERY (VOLTAGE)
a.

Inspect the transmitter battery capacity.

i.

Remove the transmitter battery from the door control transmitter module set sub-assembly that does not operate. Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative (-) terminal.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/o Smart Entry and Start System)>REPLACEMENT

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between the terminals, or solder it. A terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.




b.
B281814

Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.

NOTICE:

When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter module set sub-assembly from being damaged.



c.
B281815

Check the transmitter battery voltage.

HINT:

Measure the transmitter battery voltage while pressing the lock or unlock switch on the door control transmitter module set sub-assembly.


Standard Voltage:
Connection Condition Specified Condition
Transmitter battery positive (+) - Transmitter battery negative (-) Ignition switch off, all doors closed and lock or unlock switch pressed 2.5 to 3.2 V



Result:
Proceed to
OK
NG



OK

REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY

NG

5.CHECK WAVE ENVIRONMENT
a.

Bring the door control transmitter module set sub-assembly near the door control receiver, and perform wireless operation check.

HINT:
·

When the door control transmitter module set sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



OK:

Wireless functions operate properly.



Result:
Proceed to
OK
NG



OK

END (AFFECTED BY WAVE INTERFERENCE)

NG

6.SWITCH TO SELF-DIAGNOSTIC MODE (USING GTS)
6.SWITCH TO SELF-DIAGNOSTIC MODE (USING GTS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Utility / Wireless Door Lock Diagnosis Mode.

Body Electrical > Main Body > Utility
Tester Display
Wireless Door Lock Diagnosis Mode
50005 123 2164

e.

Proceed to the next step in accordance with the prompts on the GTS screen.


f.
B220865E44
0.125,0.031 1.802,0.323 1.677,0.292 12 false Interior Light Output: 0.635,1.406 1.063,1.688 0.427,0.281 10 false ON 0.573,1.698 1.042,2.01 0.469,0.313 10 false OFF 1.552,2.167 1.917,2.5 0.365,0.333 10 false T1 2.146,2.167 2.604,2.604 0.458,0.438 10 false T2 1.979,2.604 3.427,3.042 1.448,0.438 10 false T1: 0.25 seconds 1.979,2.917 3.292,3.313 1.313,0.396 10 false T2: 0.5 seconds 1.802,2.167 2.125,2.51 0.323,0.344 10 false T1

Check that the system has switched to self-diagnostic mode by checking the interior light output pattern.


Result:
Proceed to
NEXT



NEXT

7.CHECK SELF DIAGNOSTIC MODE
7.CHECK SELF DIAGNOSTIC MODE
a.

Inspect the diagnostic outputs when the door control transmitter module set sub-assembly switch is pressed. The diagnostic outputs can be checked by the interior light flash pattern.

B357193E05
0.083,0.083 4.125,0.323 4.042,0.24 12 false Interior Light Output: 0.292,0.865 2.583,1.063 2.292,0.198 10 false Normal Wave (A) 0.292,1.198 3.354,1.5 3.063,0.302 10 false (Lock/Unlock/Back Door*1/Panic*2 Switch): 0.438,1.813 0.75,2.01 0.313,0.198 10 false ON 0.427,2.188 0.74,2.385 0.313,0.198 10 false OFF 1.219,2.625 1.531,2.823 0.313,0.198 10 false T1 1.708,2.635 2.021,2.833 0.313,0.198 10 false T2 0.573,3.479 3.031,3.698 2.458,0.219 10 false T1: 0.25 seconds (Interior Light) 0.573,3.875 3.031,4.094 2.458,0.219 10 false T2: 0.5 seconds (Interior Light) 4.125,0.396 6.583,0.615 2.458,0.219 10 false Unmatching Recognition Code (B): 4.156,0.979 4.469,1.177 0.313,0.198 10 false ON 4.156,1.375 4.469,1.573 0.313,0.198 10 false OFF 4.938,1.844 6.563,2.052 1.625,0.208 10 false Wave is being received 4.188,2.604 6.646,2.823 2.458,0.219 10 false No Diagnostic Output (C): 4.156,3.198 4.469,3.396 0.313,0.198 10 false OFF 4.844,4.24 6.438,4.646 1.594,0.406 10 false *2: w/ Panic Function 4.823,3.896 7,4.396 2.177,0.5 10 false *1: w/ Power Back Door System


Result:
Result Proceed to
Normal wave (light flash pattern) is output A
Unmatching recognition code is output B
No diagnostic outputs C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

8.CHECK REGISTER RECOGNITION CODE

C

9.CHECK DOOR CONTROL RECEIVER (RESPONSE)
8.CHECK REGISTER RECOGNITION CODE
a.

Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System)>REGISTRATION

OK:

Recognition code can be registered.



Result:
Proceed to
OK
NG



OK

END (GO TO OPERATION CHECK)

NG

13.REPLACE DOOR CONTROL RECEIVER
9.CHECK DOOR CONTROL RECEIVER (RESPONSE)
a.

Prepare a door control transmitter module set sub-assembly from another vehicle.


b.

Press and hold a door control transmitter module set sub-assembly switch.


c.

Check that an unmatching recognition code is output.

OK:

Unmatching recognition code is output.



Result:
Proceed to
OK
NG



OK

REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY

NG

10.CHECK DOOR CONTROL RECEIVER (+B, GND)
10.CHECK DOOR CONTROL RECEIVER (+B, GND)
a.
B281165C12
1.49,0.146 1.906,0.375 0.417,0.229 2.594,1.406 2.208,1.406 false 1.219,1.406 0.833,1.406 false 0.219,0.146 0.396,0.292 0.177,0.146 10 false *a 0.469,1.333 1.073,1.573 0.604,0.24 10 false GND 2.667,1.323 3.063,1.646 0.396,0.323 10 false +B 1.573,0.177 2.406,0.51 0.833,0.333 10 false M26
*a Front view of wire harness connector
(to Door Control Receiver)


Disconnect the M26 door control receiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M26-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M26-5 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK DOOR CONTROL RECEIVER (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK DOOR CONTROL RECEIVER (OUTPUT)
a.

Reconnect the M26 door control receiver connector.


b.
B281169C07
1.49,0.375 1.927,0.604 0.438,0.229 1.875,1.281 1.875,1.875 1.875,1.875 2.365,1.875 false 0.24,0.167 0.583,0.49 0.344,0.323 10 false *a 2.417,1.792 2.74,1.938 0.323,0.146 10 false RDA 1.583,0.406 1.958,0.583 0.375,0.177 10 false M26
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M26-2 (RDA) - Body ground Ignition switch off, all doors closed and door control transmitter module set sub-assembly switch not pressed 11 to 14 V
Ignition switch off, all doors closed and door control transmitter module set sub-assembly switch pressed Pulse generation
(0 to 12 V)



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - DOOR CONTROL RECEIVER)

NG

12.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - DOOR CONTROL RECEIVER)
a.

Disconnect the F19 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the M26 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M26-2 (RDA) - F19-4 (RDA) Always Below 1 Ω
M26-3 (PRG) - F19-5 (PRG) Always Below 1 Ω
M26-2 (RDA) or F19-4 (RDA) - Body ground Always 10 kΩ or higher
M26-3 (PRG) or F19-5 (PRG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE DOOR CONTROL RECEIVER
a.

Temporarily replace the door control receiver with a new or known good one.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER(w/o Tire Pressure Warning System)>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.REGISTER RECOGNITION CODE
14.REGISTER RECOGNITION CODE

Result:
Proceed to
NEXT



NEXT

15.CHECK DOOR CONTROL RECEIVER (OPERATION)
15.CHECK DOOR CONTROL RECEIVER (OPERATION)
a.

Check that the doors can be locked and unlocked by the door control transmitter module set sub-assembly lock and unlock switches.

OK:

Doors can be locked and unlocked by the door control transmitter module set sub-assembly.



Result:
Proceed to
OK
NG



OK

END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)