Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › from 2017.10
RM3160E _58 Vehicle Interior _019716 INTERIOR PANELS / TRIM _0107108 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REASSEMBLY  


PROCEDURE

Hide 82171 1.INSTALL NO. 1 ROOF WIRE (for Normal Roof)

a.

Apply butyl tape as shown in the illustration.

B360493C01
3.5,0.885 3.833,0.885 3.833,0.885 3.833,0.302 true 3.5,1.146 3.5,0.729 false 3.448,1.146 3.76,1.344 0.313,0.198 10 false *a
*a Marking - -
V100155

Butyl Tape - -


NOTICE:

Securely attach butyl tape.



b.

Engage each clamp.

B490064C01
3.5,1.094 3.917,0.677 true 5.792,1.792 6.073,1.792 true 4.625,2.167 4.958,1.833 true 4.438,2.26 4.615,2.906 4.615,2.906 4.792,2.25 true 3.688,1.458 4.292,1.229 4.292,1.229 4,1.438 true 4.177,1.688 4.521,1.552 true 0.781,0.74 0.969,0.563 true 0.76,2.042 0.948,1.865 true 0.708,2.719 0.875,2.635 true 0.729,3.427 0.906,3.271 true 0.198,0.229 0.563,0.49 0.365,0.26 12 false *A 0.208,1.521 0.583,1.823 0.375,0.302 12 false *B 0.573,0.667 0.99,0.927 0.417,0.26 12 false *C 3.24,3.5 3.552,3.656 0.313,0.156 10 false *a 4.531,1.448 4.75,1.615 0.219,0.167 10 true *b 4.552,2.906 4.865,3.063 0.313,0.156 10 false *c 3.938,0.583 4.25,0.74 0.313,0.156 10 false *d 2.188,0.646 2.365,0.823 0.177,0.177 10 true *e 2.188,2.406 2.365,2.583 0.177,0.177 10 true *e 6.104,1.698 6.333,1.854 0.229,0.156 10 true *d 4.979,1.75 5.208,1.906 0.229,0.156 10 true *b 4.333,1.135 4.531,1.313 0.198,0.177 10 true *c 0.552,1.948 0.969,2.208 0.417,0.26 12 false *C 0.5,2.625 0.917,2.885 0.417,0.26 12 false *D 0.521,3.333 0.938,3.594 0.417,0.26 12 false *E
*A w/o Pre-collision System *B w/ Pre-collision System
*C for LHD with Rain Sensor *D w/ EC Mirror
*E for RHD with Rain Sensor - -
*a Marking Tape (A) *b Marking Tape (B)
*c Marking *d Adjustment Area
*e 45° - -



c.

Turn the 2 visor connectors clockwise approximately 45° to install them to the roof headlining assembly.


d.

Align the marking tape (A) on the No. 1 roof wire with the vehicle front side tab of the roof headlining assembly.


e.

Align the edge of the 2 marking tapes (B) on the No. 1 roof wire with the markings on the roof headlining assembly.


f.

Attach the No. 1 roof wire with the butyl tape.

NOTICE:
·

Securely attach the No. 1 roof wire.

·

If any of the No. 1 roof wire is left loose, it will cause an abnormal noise.

·

Make sure to attach the No. 1 roof wire without leaving any of it loose.



HINT:

Secure the extra length of the No. 1 roof wire in the adjustment area.



g.

Install the No. 1 roof wire to the roof headlining assembly with adhesive tape.

B490065C01
0.167,4.333 3.167,5.5 3,1.167 3.167,4.333 5.083,5.5 1.917,1.167 5.083,4.333 7,5.5 1.917,1.167 1.052,0.813 0.917,0.615 0.917,0.615 1.302,0.615 true 6.063,4.948 6.396,4.813 true 1.042,2.021 0.906,1.823 0.906,1.823 1.292,1.823 true 0.99,2.813 0.906,2.521 0.906,2.521 1.302,2.729 true 1.083,3.448 0.885,3.656 0.885,3.656 1.292,3.583 true 4.146,4.938 4.479,4.802 true 0.198,0.479 0.573,0.823 0.375,0.344 12 false *A 0.208,1.646 0.583,1.938 0.375,0.292 12 false *B 0.698,0.521 1.104,0.885 0.406,0.365 12 false *C 4.479,4.708 4.792,4.865 0.313,0.156 10 false *1 0.25,4.417 0.563,4.573 0.313,0.156 10 false *a 3.25,4.417 3.563,4.573 0.313,0.156 10 false *b 5.188,4.427 5.5,4.583 0.313,0.156 10 false *c 3.698,5.26 4.01,5.417 0.313,0.156 10 false *d 4.469,5.26 4.781,5.417 0.313,0.156 10 false *d 6.417,4.719 6.729,4.875 0.313,0.156 10 false *1 0.563,5.146 0.875,5.302 0.313,0.156 10 false A 1.229,4.74 1.542,4.896 0.313,0.156 10 false B 1.99,5.135 2.302,5.292 0.313,0.156 10 false C 2.688,4.74 3,4.896 0.313,0.156 10 false D 0.688,1.74 1.094,2.104 0.406,0.365 12 false *C 0.688,2.417 1.094,2.781 0.406,0.365 12 false *D 0.667,3.563 1.073,3.927 0.406,0.365 12 false *E
*A w/o Pre-collision System *B w/ Pre-collision System
*C for LHD with Rain Sensor *D w/ EC Mirror
*E for RHD with Rain Sensor - -
*1 No. 1 Roof Wire - -
*a Adhesive Tape Size *b Correct
*c Incorrect *d 15 mm (0.591 in.) or more
V100155

Adhesive Tape - -


Adhesive Tape Size
Area Dimension
A 20 mm (0.787 in.)
B 80 mm (3.15 in.) or more
C 80 mm (3.15 in.)
D 80 mm (3.15 in.)

NOTICE:
·

Apply the tape securely in place.

·

Do not touch the adhesive surface when applying the tape to prevent adhesion failure.




Hide 82171 2.INSTALL NO. 1 ROOF WIRE (for Sliding Roof)

a.

Apply butyl tape as shown in the illustration.

B360494C01
4.656,0.885 4.906,0.885 4.906,0.885 4.906,0.302 true 4.656,0.74 4.656,1.156 false 1.594,0.313 1.969,0.552 0.375,0.24 12 true *A 4.594,1.156 4.906,1.354 0.313,0.198 10 false *a
*A w/ Rear Seat Entertainment System - -
*a Marking - -
V100155

Butyl Tape - -


NOTICE:

Securely attach butyl tape.



b.

Engage each clamp.

B456078C01
0.719,3.458 0.906,3.281 true 1.01,1.719 0.74,1.917 true 5.646,1.875 5.844,1.875 true 2.833,1.344 3.042,1.344 true 4.979,1.844 5.469,1.438 true 4.802,1.854 5.49,2.177 5.49,2.177 5.125,1.854 true 3.74,1.448 4.146,1.594 true 3.51,1.333 4.198,1.385 4.198,1.385 3.875,1.229 true 4.146,2.156 4.417,1.927 true 3.698,2.333 3.906,2.198 true 3.292,3.583 3.292,3.417 true 0.25,0.25 0.667,0.583 0.417,0.333 12 false *A 0.25,1.417 0.667,1.75 0.417,0.333 12 false *B 0.521,1.823 1,2.229 0.479,0.406 12 false *C 0.5,3.365 0.979,3.698 0.479,0.333 12 false *D 3.208,3.563 3.521,3.719 0.313,0.156 10 false *a 4.177,1.521 4.375,1.708 0.198,0.188 10 true *b 5.479,1.323 5.677,1.479 0.198,0.156 10 true *c 5.521,2.083 5.698,2.271 0.177,0.188 10 true *d 5.875,1.771 6.083,1.948 0.208,0.177 10 true *e 4.24,1.302 4.427,1.479 0.188,0.177 10 true *d 3.542,2.25 3.854,2.406 0.313,0.156 10 false *d 2.229,2.198 2.385,2.365 0.156,0.167 10 true *f 2.229,0.698 2.385,0.865 0.156,0.167 10 true *f 2.667,1.25 2.875,1.427 0.208,0.177 10 false *e 4.438,1.802 4.635,1.99 0.198,0.188 10 true *b 4.802,1.458 5.281,1.865 0.479,0.406 12 false *E
*A w/o Pre-collision System *B w/ Pre-collision System
*C for LHD with Rain Sensor *D for RHD with Rain Sensor
*E w/ Rear Seat Entertainment System - -
*a Marking Tape (A) *b Marking Tape (B)
*c Marking Tape (C) *d Marking
*e Adjustment Area *f 45°



c.

Turn the 2 visor connectors clockwise approximately 45° to install them to the roof headlining assembly.


d.

Align the marking tape (A) on the No. 1 roof wire with the vehicle front side tab of the roof headlining assembly.


e.

Align the edge of the 2 marking tapes (B) on the No. 1 roof wire with the markings on the roof headlining assembly.


f.

w/ Rear Seat Entertainment System:

i.

Align the edge of the marking tape (C) on the No. 1 roof wire with the markings on the roof headlining assembly.



g.

Attach the No. 1 roof wire with the butyl tape.

NOTICE:
·

Securely attach the No. 1 roof wire.

·

If any of the No. 1 roof wire is left loose, it will cause an abnormal noise.

·

Make sure to attach the No. 1 roof wire without leaving any of it loose.



HINT:

Secure the extra length of the No. 1 roof wire in the adjustment area.



h.

Install the No. 1 roof wire to the roof headlining assembly with adhesive tape.

B456079C01
3.25,4.25 5.083,5.583 1.833,1.333 5.083,4.25 6.917,5.583 1.833,1.333 0.167,4.25 3.25,5.583 3.083,1.333 4.146,4.938 4.438,4.854 true 6.063,4.927 6.354,4.844 true 1.052,1.875 0.781,1.677 0.781,1.677 1.281,1.719 true 1.292,3.51 0.802,3.594 0.802,3.594 1.104,3.365 true 0.25,0.167 0.667,0.5 0.417,0.333 12 false *A 0.25,1.417 0.667,1.75 0.417,0.333 12 false *B 0.563,1.563 0.875,1.802 0.313,0.24 12 false *C 0.583,3.5 0.917,3.75 0.333,0.25 12 false *D 3.688,1.656 4.083,1.917 0.396,0.26 12 false *E 4.438,4.74 4.75,4.896 0.313,0.156 10 false *1 0.25,4.333 0.563,4.49 0.313,0.156 10 false *a 3.354,4.333 3.667,4.49 0.313,0.156 10 false *b 5.167,4.333 5.479,4.49 0.313,0.156 10 false *c 6.365,4.74 6.677,4.896 0.313,0.156 10 false *1 0.531,5.104 0.688,5.302 0.156,0.198 10 false A 1.25,4.74 1.406,4.938 0.156,0.198 10 false B 1.99,5.104 2.146,5.302 0.156,0.198 10 false C 2.688,4.75 2.844,4.948 0.156,0.198 10 false D 3.688,5.292 4,5.448 0.313,0.156 10 false *d 4.458,5.292 4.771,5.448 0.313,0.156 10 false *d
*A w/o Pre-collision System *B w/ Pre-collision System
*C for LHD with Rain Sensor *D for RHD with Rain Sensor
*E w/ Rear Seat Entertainment System - -
*1 No. 1 Roof Wire - -
*a Adhesive Tape Size *b Correct
*c Incorrect *d 15 mm (0.591 in.) or more
V100155

Adhesive Tape - -


Adhesive Tape Size
Area Dimension
A 20 mm (0.787 in.)
B 80 mm (3.15 in.) or more
C 80 mm (3.15 in.)
D 80 mm (3.15 in.)

NOTICE:
·

Apply the tape securely in place.

·

Do not touch the adhesive surface when applying the tape to prevent adhesion failure.




Hide 63398 3.INSTALL ROOF HEADLINING SUPPORT PLATE (for Normal Roof)

a.

Remove the release paper from 2 new roof headlining support plates.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



b.

Install the 2 roof headlining support plates as shown in the illustration.

B360489N01
4.344,1.427 4.5,1.625 0.156,0.198 10 false A 4.354,2.24 4.51,2.438 0.156,0.198 10 false B

Standard Measurement
Area Dimension
A 14 mm (0.551 in.)
B 11 mm (0.433 in.)


Hide 63398 4.INSTALL ROOF HEADLINING SUPPORT PLATE (for Sliding Roof)

a.

Remove the release paper from 2 new roof headlining support plates.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



b.

Install the 2 roof headlining support plates as shown in the illustration.

B360491N01
5.594,1.438 5.75,1.635 0.156,0.198 10 false A 5.604,2.219 5.76,2.417 0.156,0.198 10 false B

Standard Measurement
Area Dimension
A 14 mm (0.551 in.)
B 11 mm (0.433 in.)


Hide 81390C 5.INSTALL SPOT LIGHT ASSEMBLY LH

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT>INSTALLATION

HINT:

Use the same procedure for the front side and rear side.


Hide 81360K 6.INSTALL SPOT LIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 7.INSTALL AIR DUCT SEAL

HINT:

Use the same procedure for all air duct seals.


a.

Remove the release paper from a new air duct seal.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



b.
B360488

Install the air duct seal as shown in the illustration.


Hide 8.INSTALL REAR WASHER HOSE ASSEMBLY (for Normal Roof)

a.

Apply butyl tape as shown in the illustration.

B365594C01
3.5,0.833 3.833,0.833 3.833,0.833 3.833,0.26 true 3.5,0.677 3.5,1.01 false 3.427,1.01 3.74,1.208 0.313,0.198 10 false *a
*a Marking - -
V100155

Butyl Tape - -


NOTICE:

Securely attach butyl tape.



b.

Align the edge of the marking tape on the rear washer hose assembly from the vehicle front side tab of the roof headlining assembly as shown in the illustration.

B367804C01
0.865,1.854 1.021,2.052 0.156,0.198 10 false A 5.99,1.219 6.146,1.417 0.156,0.198 10 false B 2.552,1.417 2.781,1.615 0.229,0.198 10 true *a
*a Adjustment Area - -
V100144

Marking Tape
V100145

Joint
V100155

Adhesive Tape - -


Standard Measurement
Area Dimension
A 246 +/- 6 mm (9.69 +/- 0.236 in.)
B 41 +/- 6 mm (1.61 +/- 0.236 in.)


c.

Align the edge of the joint to the rear washer hose assembly from the vehicle rear side of the roof headlining assembly as shown in the illustration.


d.

Attach the rear washer hose assembly with the butyl tape to install the rear washer hose assembly.

NOTICE:
·

Securely attach the rear washer hose assembly.

·

If any of the rear washer hose assembly is left loose, it will cause an abnormal noise.

·

Make sure to attach the rear washer hose assembly without leaving any of it loose.



HINT:

Secure the extra length of the rear washer hose assembly in the adjustment area using the adhesive tape as shown in the illustration.



Hide 9.INSTALL REAR WASHER HOSE ASSEMBLY (for Sliding Roof)

a.

Apply butyl tape as shown in the illustration.

B365594C02
3.5,0.844 3.833,0.844 3.833,0.844 3.833,0.26 true 3.5,0.688 3.5,1.021 false 3.427,1.021 3.74,1.219 0.313,0.198 10 false *a
*a Marking - -
V100155

Butyl Tape - -


NOTICE:

Securely attach butyl tape.



b.

Align the edge of the marking tape on the rear washer hose assembly from the vehicle front side tab of the roof headlining assembly as shown in the illustration.

B367801C01
0.875,1.865 1.031,2.063 0.156,0.198 10 false A 6.021,1.302 6.177,1.5 0.156,0.198 10 false B 2.521,1.438 2.74,1.646 0.219,0.208 10 true *a
*a Adjustment Area - -
V100144

Marking Tape
V100145

Joint
V100155

Adhesive Tape - -


Standard Measurement
Area Dimension
A 246 +/- 6 mm (9.69 +/- 0.236 in.)
B 41 +/- 6 mm (1.61 +/- 0.236 in.)


c.

Align the edge of the joint to the rear washer hose assembly from the vehicle rear side of the roof headlining assembly as shown in the illustration.


d.

Attach the rear washer hose assembly with the butyl tape.

NOTICE:
·

Securely attach the rear washer hose assembly.

·

If any of the rear washer hose assembly is left loose, it will cause an abnormal noise.

·

Make sure to attach the rear washer hose assembly without leaving any of it loose.



HINT:

Secure the extra length of the rear washer hose assembly in the adjustment area using the adhesive tape as shown in the illustration.



e.

Engage each clamp to install the rear washer hose assembly.


Hide 863C0 10.INSTALL DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY (w/ DAB Function)

Hide 86300B 11.INSTALL NO. 1 AMPLIFIER ANTENNA ASSEMBLY

Hide 86101J 12.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (for Normal Roof)

Hide 86101J 13.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (for Sliding Roof)