Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2017.10
RM3160E _51 Engine / Hybrid System _060156 2GR-FKS ENGINE CONTROL _0299070 SFI SYSTEM C

2GR-FKS ENGINE CONTROL  SFI SYSTEM  P035113  Ignition Coil "A" Circuit Open  P035213  Ignition Coil "B" Circuit Open  P035313  Ignition Coil "C" Circuit Open  P035413  Ignition Coil "D" Circuit Open  P035513  Ignition Coil "E" Circuit Open  P035613  Ignition Coil "F" Circuit Open  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P035113 is output, check the No. 1 ignition coil assembly circuit.

·

If DTC P035213 is output, check the No. 2 ignition coil assembly circuit.

·

If DTC P035313 is output, check the No. 3 ignition coil assembly circuit.

·

If DTC P035413 is output, check the No. 4 ignition coil assembly circuit.

·

If DTC P035513 is output, check the No. 5 ignition coil assembly circuit.

·

If DTC P035613 is output, check the No. 6 ignition coil assembly circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A373699E01
4.104,1.073 3.979,0.542 3.979,0.542 3.844,0.542 false 5.167,0.958 5.479,0.573 5.479,0.573 5.625,0.573 false 0.198,1.542 1.438,2.021 1.24,0.479 10 false Crankshaft Position Sensor 0.552,3.542 1.49,3.792 0.938,0.25 10 false VVT Sensor 0.135,4.865 1.677,5.885 1.542,1.021 10 false Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter Sub-assembly, Throttle Position Sensor, etc.) 2.531,1.125 3.146,1.323 0.615,0.198 10 false IGT1 2.563,1.542 3.177,1.74 0.615,0.198 10 false IGF1 2.573,2.969 3.188,3.167 0.615,0.198 10 false IGT2 2.573,3.375 3.188,3.573 0.615,0.198 10 false IGF2 2.583,3.833 3.198,4.031 0.615,0.198 10 false IGT3 2.594,4.708 3.208,4.906 0.615,0.198 10 false IGT4 2.594,5.583 3.208,5.781 0.615,0.198 10 false IGT5 2.583,6.469 3.198,6.667 0.615,0.198 10 false IGT6 2.438,7.177 2.896,7.375 0.458,0.198 10 false ECM 3.417,0.458 4.49,0.656 1.073,0.198 10 false Igniter 4.365,0.427 5.24,0.719 0.875,0.292 10 false from Battery 5.698,0.5 6.823,0.938 1.125,0.438 10 false No. 1 Ignition Coil Assembly 4.375,1.677 5.177,1.948 0.802,0.271 10 false Ignition Coil 5.5,1.76 6.667,2.063 1.167,0.302 10 false No. 1 Spark Plug 3.948,2.906 5.063,3.344 1.115,0.438 10 false No. 2 Ignition Coil Assembly 3.927,3.771 5.073,4.156 1.146,0.385 10 false No. 3 Ignition Coil Assembly 3.906,4.635 5.052,5.063 1.146,0.427 10 false No. 4 Ignition Coil Assembly 3.927,5.531 5.063,5.979 1.135,0.448 10 false No. 5 Ignition Coil Assembly 3.906,6.396 5.052,6.813 1.146,0.417 10 false No. 6 Ignition Coil Assembly 5.5,3.354 6.677,3.656 1.177,0.302 10 false No. 2 Spark Plug 5.521,4.26 6.729,4.531 1.208,0.271 10 false No. 3 Spark Plug 5.552,5.104 6.698,5.396 1.146,0.292 10 false No. 4 Spark Plug 5.583,5.99 6.729,6.281 1.146,0.292 10 false No. 5 Spark Plug 5.583,6.875 6.771,7.115 1.188,0.24 10 false No. 6 Spark Plug

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P035113 Ignition Coil "A" Circuit Open No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT1 circuit between ignition coil assembly and ECM

·

No. 1 ignition coil assembly

·

Semiconductor pwr integration ECU

·

ECM


Comes on DTC stored SAE Code: P0351
P035213 Ignition Coil "B" Circuit Open No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF2 or IGT2 circuit between ignition coil assembly and ECM

·

No. 2 ignition coil assembly

·

Semiconductor pwr integration ECU

·

ECM


Comes on DTC stored SAE Code: P0352
P035313 Ignition Coil "C" Circuit Open No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT3 circuit between ignition coil assembly and ECM

·

No. 3 ignition coil assembly

·

Semiconductor pwr integration ECU

·

ECM


Comes on DTC stored SAE Code: P0353
P035413 Ignition Coil "D" Circuit Open No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF2 or IGT4 circuit between ignition coil assembly and ECM

·

No. 4 ignition coil assembly

·

Semiconductor pwr integration ECU

·

ECM


Comes on DTC stored SAE Code: P0354
P035513 Ignition Coil "E" Circuit Open No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT5 circuit between ignition coil assembly and ECM

·

No. 5 ignition coil assembly

·

Semiconductor pwr integration ECU

·

ECM


Comes on DTC stored SAE Code: P0355
P035613 Ignition Coil "F" Circuit Open No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF2 or IGT6 circuit between ignition coil assembly and ECM

·

No. 6 ignition coil assembly

·

Semiconductor pwr integration ECU

·

ECM


Comes on DTC stored SAE Code: P0356

A369419E01
0.031,0.052 0.583,0.271 0.552,0.219 10 false 2 V/DIV. 0.135,0.781 0.469,1 0.333,0.219 10 false CH1 0.146,1.25 0.469,1.458 0.323,0.208 10 false CH2 1.25,1.948 2.073,2.167 0.823,0.219 10 false 20 ms./DIV. 2.99,0.99 3.365,1.219 0.375,0.229 10 false GND 2.99,1.635 3.354,1.844 0.365,0.208 10 false GND

Reference: Inspection using an oscilloscope.

HINT:
·

The correct waveform is as shown.


·

While idling the engine, check the waveform between terminals IGT (1 to 6) and E1, and IGF (1 or 2) and E1 of the ECM connector.



ECM Terminal Name CH1: Between IGT (1 to 6) and E1
CH2: Between IGF (1 or 2) and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


MONITOR DESCRIPTION

A212405E24
1.782,1.645 2.181,1.818 0.399,0.173 10 ECM 2.956,1.3 3.225,1.485 0.269,0.185 10 IGT 2.949,1.726 3.226,1.886 0.278,0.160 10 IGF 4.153,1.509 4.594,1.655 0.441,0.145 10 Igniter 5.4,1.348 6.167,1.521 0.767,0.173 10 Ignition Coil 4.465,2.35 6.163,2.540 1.698,0.191 10 Ignition Coil Assembly 0.213,3.113 1.146,3.443 0.934,0.330 10 Ignition Signal (IGT) 1.642,3.541 2.131,3.731 0.489,0.191 10 Normal 1.383,3.947 2.150,4.138 0.767,0.191 10 Malfunction 0.262,3.907 1.146,4.768 0.884,0.862 10 Ignition Confirmation Signal (IGF) 3.449,4.507 4.628,4.684 1.179,0.177 10 Circuit Malfunction 5.95,4.97 6.314,5.167 0.364,0.198 10 Time

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Igniter
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more [A].

8.

Enter the following menus: Powertrain / Engine / Trouble Codes [B].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P035113, P035213, P035313, P035413, P035513 or P035613.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.




WIRING DIAGRAM

A373702E03
0.542,8.083 1.615,8.281 1.073,0.198 10 false Battery 0.406,7.094 1.479,7.292 1.073,0.198 10 false FL MAIN 1.052,5.302 2.573,5.885 1.521,0.583 10 false Certification ECU (Smart Key ECU Assembly) 1.063,5.083 1.521,5.281 0.458,0.198 10 false F10 1.521,4.521 2.135,4.719 0.615,0.198 10 false IG1D 1.885,4.417 2.198,4.615 0.313,0.198 10 false 3 0.74,2.542 1.969,3 1.229,0.458 10 false Semiconductor Pwr Integration ECU 0.24,2.333 0.396,2.531 0.156,0.198 10 false B 0.448,1.083 1.125,1.354 0.677,0.271 10 false IG2-MAIN 1.375,1.781 1.833,1.979 0.458,0.198 10 false IG2 1.896,1.104 2.313,1.313 0.417,0.208 10 false INJ 2.188,2.323 2.5,2.521 0.313,0.198 10 false 1E 2.313,2.125 2.469,2.323 0.156,0.198 10 false 1 2.427,0.938 2.74,1.135 0.313,0.198 10 false 1G 2.469,0.75 2.625,0.948 0.156,0.198 10 false 3 3.573,0.813 3.729,1.01 0.156,0.198 10 false 1 3.583,1.219 3.74,1.417 0.156,0.198 10 false 4 4.719,0.823 4.875,1.021 0.156,0.198 10 false 3 4.719,1.208 4.844,1.406 0.125,0.198 10 false 2 3.563,2.073 3.719,2.271 0.156,0.198 10 false 1 4.729,2.063 4.885,2.26 0.156,0.198 10 false 3 3.573,2.479 3.729,2.677 0.156,0.198 10 false 4 4.719,2.448 4.875,2.646 0.156,0.198 10 false 2 3.563,3.354 3.719,3.552 0.156,0.198 10 false 1 4.719,3.354 4.875,3.552 0.156,0.198 10 false 3 3.573,3.729 3.729,3.927 0.156,0.198 10 false 4 4.729,3.719 4.885,3.917 0.156,0.198 10 false 2 3.573,4.583 3.729,4.781 0.156,0.198 10 false 1 4.719,4.594 4.875,4.792 0.156,0.198 10 false 3 3.573,4.99 3.729,5.188 0.156,0.198 10 false 4 4.719,4.99 4.875,5.188 0.156,0.198 10 false 2 3.563,5.844 3.719,6.042 0.156,0.198 10 false 1 4.719,5.844 4.875,6.042 0.156,0.198 10 false 3 3.573,6.25 3.729,6.448 0.156,0.198 10 false 4 4.74,6.24 4.896,6.438 0.156,0.198 10 false 2 3.583,7.073 3.74,7.271 0.156,0.198 10 false 1 4.719,7.094 4.875,7.292 0.156,0.198 10 false 3 3.594,7.469 3.75,7.667 0.156,0.198 10 false 4 4.719,7.479 4.875,7.677 0.156,0.198 10 false 2 3.75,0.938 4.063,1.135 0.313,0.198 10 false +B 3.76,2.177 4.073,2.375 0.313,0.198 10 false +B 3.76,3.458 4.073,3.656 0.313,0.198 10 false +B 3.74,4.698 4.052,4.896 0.313,0.198 10 false +B 3.75,5.969 4.063,6.167 0.313,0.198 10 false +B 3.74,7.208 4.052,7.406 0.313,0.198 10 false +B 3.74,1.333 4.198,1.531 0.458,0.198 10 false GND 3.75,2.573 4.208,2.771 0.458,0.198 10 false GND 3.74,3.823 4.198,4.021 0.458,0.198 10 false GND 3.729,5.083 4.188,5.281 0.458,0.198 10 false GND 3.719,6.344 4.177,6.542 0.458,0.198 10 false GND 3.729,7.594 4.188,7.792 0.458,0.198 10 false GND 4.354,0.927 4.781,1.125 0.427,0.198 10 false IGT1 4.333,2.198 4.948,2.396 0.615,0.198 10 false IGT3 4.333,3.438 4.948,3.635 0.615,0.198 10 false IGT5 4.344,4.708 4.958,4.906 0.615,0.198 10 false IGT2 4.344,5.927 4.958,6.125 0.615,0.198 10 false IGT4 4.344,7.219 4.958,7.417 0.615,0.198 10 false IGT6 4.323,1.302 4.938,1.5 0.615,0.198 10 false IGF1 4.323,2.552 4.938,2.75 0.615,0.198 10 false IGF1 4.333,3.813 4.948,4.01 0.615,0.198 10 false IGF1 4.344,5.073 4.958,5.271 0.615,0.198 10 false IGF2 4.323,6.333 4.938,6.531 0.615,0.198 10 false IGF2 4.323,7.583 4.938,7.781 0.615,0.198 10 false IGF2 3.104,1.625 3.427,1.833 0.323,0.208 10 false C42 3.104,2.854 3.438,3.063 0.333,0.208 10 false C45 3.125,4.146 3.458,4.354 0.333,0.208 10 false C48 3.125,5.417 3.448,5.625 0.323,0.208 10 false C43 3.146,6.656 3.469,6.865 0.323,0.208 10 false C46 3.156,7.896 3.479,8.104 0.323,0.208 10 false C49 3.542,7.896 5.427,8.135 1.885,0.24 10 false No. 6 Ignition Coil Assembly 3.49,6.656 5.333,6.958 1.844,0.302 10 false No. 4 Ignition Coil Assembly 3.49,5.417 5.365,5.677 1.875,0.26 10 false No. 2 Ignition Coil Assembly 3.5,4.146 5.375,4.427 1.875,0.281 10 false No. 5 Ignition Coil Assembly 3.469,2.875 5.323,3.219 1.854,0.344 10 false No. 3 Ignition Coil Assembly 3.448,1.625 5.323,1.906 1.875,0.281 10 false No. 1 Ignition Coil Assembly 6.063,7.958 6.521,8.156 0.458,0.198 10 false C1 6.302,7.958 6.76,8.156 0.458,0.198 10 false ECM 5.698,0.781 6.01,0.979 0.313,0.198 10 false 71 5.625,1.198 6.083,1.396 0.458,0.198 10 false 112 5.698,2.052 6.01,2.25 0.313,0.198 10 false 70 5.708,3.281 6.021,3.479 0.313,0.198 10 false 69 5.698,4.542 6.01,4.74 0.313,0.198 10 false 36 5.708,4.979 6.021,5.177 0.313,0.198 10 false 80 5.698,5.813 6.01,6.01 0.313,0.198 10 false 35 5.708,7.083 6.021,7.281 0.313,0.198 10 false 34 5.927,7.083 6.302,7.302 0.375,0.219 10 false IGT6 5.927,5.813 6.542,6.01 0.615,0.198 10 false IGT4 5.917,4.969 6.531,5.167 0.615,0.198 10 false IGF2 5.927,4.552 6.542,4.75 0.615,0.198 10 false IGT2 5.927,3.281 6.542,3.479 0.615,0.198 10 false IGT5 5.917,2.052 6.531,2.25 0.615,0.198 10 false IGT3 5.906,1.188 6.521,1.385 0.615,0.198 10 false IGF1 5.927,0.781 6.542,0.979 0.615,0.198 10 false IGT1 0.333,2.115 0.49,2.313 0.156,0.198 10 false 1 0.104,0.063 3.771,0.479 3.667,0.417 12 false w/ Smart Entry and Start System:

A399935E01
0.083,0.031 2.885,0.417 2.802,0.385 12 false w/o Smart Entry and Start System: 0.563,8.083 1.344,8.417 0.781,0.333 10 false Battery 0.427,7.125 1.146,7.531 0.719,0.406 10 false FL MAIN 0.719,5.344 1.146,5.698 0.427,0.354 10 false ST 0.844,4.396 1.052,4.625 0.208,0.229 10 false 4 1.021,4.396 1.479,4.594 0.458,0.198 10 false AM2 1.677,4.396 2.094,4.677 0.417,0.281 10 false IG2 1.99,4.396 2.156,4.615 0.167,0.219 10 false 3 0.75,4.844 1.156,5.135 0.406,0.292 10 false F50 1.042,4.823 1.979,5.229 0.938,0.406 10 false Ignition Switch Assembly 0.25,2.323 0.406,2.521 0.156,0.198 10 false B 0.354,2.125 0.51,2.323 0.156,0.198 10 false 1 2.198,2.333 2.51,2.531 0.313,0.198 10 false 1E 2.344,2.135 2.5,2.333 0.156,0.198 10 false 1 0.75,2.542 1.969,2.958 1.219,0.417 10 false Semiconductor Pwr Integration ECU 0.469,1.094 1.177,1.385 0.708,0.292 10 false IG2-MAIN 1.365,1.75 1.823,1.948 0.458,0.198 10 false IG2 1.969,1.104 2.427,1.302 0.458,0.198 10 false INJ 2.438,0.927 2.75,1.125 0.313,0.198 10 false 1G 2.49,0.729 2.646,0.927 0.156,0.198 10 false 3 3.552,0.833 3.708,1.031 0.156,0.198 10 false 1 3.552,2.031 3.708,2.229 0.156,0.198 10 false 1 3.573,3.313 3.729,3.51 0.156,0.198 10 false 1 3.573,4.583 3.729,4.781 0.156,0.198 10 false 1 3.552,5.813 3.708,6.01 0.156,0.198 10 false 1 3.563,7.083 3.719,7.281 0.156,0.198 10 false 1 3.75,0.917 4.063,1.115 0.313,0.198 10 false +B 3.75,2.167 4.063,2.365 0.313,0.198 10 false +B 3.75,3.438 4.063,3.635 0.313,0.198 10 false +B 3.74,4.698 4.052,4.896 0.313,0.198 10 false +B 3.76,5.938 4.073,6.135 0.313,0.198 10 false +B 3.76,7.177 4.073,7.375 0.313,0.198 10 false +B 3.573,1.229 3.729,1.427 0.156,0.198 10 false 4 3.563,2.458 3.719,2.656 0.156,0.198 10 false 4 3.594,3.708 3.75,3.906 0.156,0.198 10 false 4 3.583,4.979 3.74,5.177 0.156,0.198 10 false 4 3.573,6.229 3.729,6.427 0.156,0.198 10 false 4 3.573,7.479 3.729,7.677 0.156,0.198 10 false 4 3.729,1.313 4.188,1.51 0.458,0.198 10 false GND 3.74,2.573 4.198,2.771 0.458,0.198 10 false GND 3.719,3.844 4.177,4.042 0.458,0.198 10 false GND 3.74,5.104 4.198,5.302 0.458,0.198 10 false GND 3.76,6.344 4.219,6.542 0.458,0.198 10 false GND 3.75,7.604 4.208,7.802 0.458,0.198 10 false GND 4.729,0.823 4.885,1.021 0.156,0.198 10 false 3 4.729,2.083 4.885,2.281 0.156,0.198 10 false 3 4.75,3.323 4.906,3.521 0.156,0.198 10 false 3 4.75,4.594 4.906,4.792 0.156,0.198 10 false 3 4.76,5.844 4.917,6.042 0.156,0.198 10 false 3 4.75,7.094 4.906,7.292 0.156,0.198 10 false 3 4.354,0.938 4.969,1.135 0.615,0.198 10 false IGT1 4.344,2.188 4.958,2.385 0.615,0.198 10 false IGT3 4.354,3.448 4.969,3.646 0.615,0.198 10 false IGT5 4.344,4.708 4.958,4.906 0.615,0.198 10 false IGT2 4.323,5.948 4.938,6.146 0.615,0.198 10 false IGT4 4.333,7.198 4.948,7.396 0.615,0.198 10 false IGT6 4.74,1.177 4.896,1.375 0.156,0.198 10 false 2 4.729,2.458 4.885,2.656 0.156,0.198 10 false 2 4.76,3.708 4.917,3.906 0.156,0.198 10 false 2 4.771,4.969 4.927,5.167 0.156,0.198 10 false 2 4.76,6.208 4.917,6.406 0.156,0.198 10 false 2 4.75,7.458 4.906,7.656 0.156,0.198 10 false 2 4.333,1.323 4.948,1.521 0.615,0.198 10 false IGF1 4.333,2.583 4.948,2.781 0.615,0.198 10 false IGF1 4.302,3.802 4.917,4 0.615,0.198 10 false IGF1 4.323,5.052 4.938,5.25 0.615,0.198 10 false IGF2 4.302,6.323 4.917,6.521 0.615,0.198 10 false IGF2 4.313,7.594 4.927,7.792 0.615,0.198 10 false IGF2 3.26,1.625 3.719,1.823 0.458,0.198 10 false C42 3.615,1.635 5.573,2.021 1.958,0.385 10 false No. 1 Ignition Coil Assembly 3.292,2.875 3.75,3.073 0.458,0.198 10 false C45 3.625,2.885 5.521,3.208 1.896,0.323 10 false No. 3 Ignition Coil Assembly 3.344,4.135 3.802,4.333 0.458,0.198 10 false C48 3.688,4.146 5.604,4.406 1.917,0.26 10 false No. 5 Ignition Coil Assembly 3.385,5.375 3.844,5.573 0.458,0.198 10 false C43 3.719,5.375 5.656,5.656 1.938,0.281 10 false No. 2 Ignition Coil Assembly 3.438,6.635 3.896,6.833 0.458,0.198 10 false C46 3.75,6.625 5.646,6.906 1.896,0.281 10 false No. 4 Ignition Coil Assembly 3.448,7.896 3.906,8.094 0.458,0.198 10 false C49 3.771,7.885 5.76,8.156 1.99,0.271 10 false No. 6 Ignition Coil Assembly 6.01,7.969 6.323,8.167 0.313,0.198 10 false C1 6.271,7.979 6.729,8.177 0.458,0.198 10 false ECM 5.688,7.083 6,7.281 0.313,0.198 10 false 34 5.938,7.073 6.552,7.271 0.615,0.198 10 false IGT6 5.688,5.813 6,6.01 0.313,0.198 10 false 35 5.948,5.802 6.563,6 0.615,0.198 10 false IGT4 5.656,4.979 5.969,5.177 0.313,0.198 10 false 80 5.927,4.958 6.542,5.156 0.615,0.198 10 false IGF2 5.667,4.563 5.979,4.76 0.313,0.198 10 false 36 5.938,4.542 6.552,4.74 0.615,0.198 10 false IGT2 5.677,3.313 5.99,3.51 0.313,0.198 10 false 69 5.938,3.302 6.552,3.5 0.615,0.198 10 false IGT5 5.667,2.01 5.979,2.208 0.313,0.198 10 false 70 5.938,2.021 6.552,2.219 0.615,0.198 10 false IGT3 5.604,1.219 6.063,1.417 0.458,0.198 10 false 112 5.938,1.219 6.552,1.417 0.615,0.198 10 false IGF1 5.646,0.792 5.958,0.99 0.313,0.198 10 false 71 5.948,0.792 6.563,0.99 0.615,0.198 10 false IGT1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK WHETHER DTC OUTPUT RECURS (DTC P035113, P035213, P035313, P035413, P035513 OR P035613)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 6 cylinders).

NOTICE:

Do not change the location of the connectors.



f.

Perform a simulation test.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
Same DTC output A
Different ignition coil DTC output B


HINT:

Perform "Inspection After Repair" after replacing the ignition coil assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)

B

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
A399936C01
0.302,0.802 0.646,1.031 0.344,0.229 0.688,0.802 1.042,1.031 0.354,0.229 0.313,1.073 0.656,1.281 0.344,0.208 0.698,1.063 1.031,1.292 0.333,0.229 0.313,1.323 0.667,1.552 0.354,0.229 0.698,1.323 1.031,1.552 0.333,0.229 1.208,1.688 1.51,1.188 true 0.344,0.823 0.802,1.021 0.458,0.198 10 false C42 0.719,0.823 1.177,1.021 0.458,0.198 10 false C43 0.344,1.083 0.802,1.281 0.458,0.198 10 false C45 0.719,1.073 1.177,1.271 0.458,0.198 10 false C46 0.354,1.344 0.813,1.542 0.458,0.198 10 false C48 0.729,1.344 1.188,1.542 0.458,0.198 10 false C49 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 1.073,1.74 1.385,1.938 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Ignition Coil Assembly)


a.

Disconnect the ignition coil assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C42-1 (+B) - Body ground Ignition switch ON 11 to 14 V
C43-1 (+B) - Body ground Ignition switch ON 11 to 14 V
C45-1 (+B) - Body ground Ignition switch ON 11 to 14 V
C46-1 (+B) - Body ground Ignition switch ON 11 to 14 V
C48-1 (+B) - Body ground Ignition switch ON 11 to 14 V
C49-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - IGNITION COIL ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the ignition coil assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C42-4 (GND) - Body ground Always Below 1 Ω
C43-4 (GND) - Body ground Always Below 1 Ω
C45-4 (GND) - Body ground Always Below 1 Ω
C46-4 (GND) - Body ground Always Below 1 Ω
C48-4 (GND) - Body ground Always Below 1 Ω
C49-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C42-2 (IGF1) - C1-112 (IGF1) Always Below 1 Ω
C43-2 (IGF2) - C1-80 (IGF2) Always Below 1 Ω
C45-2 (IGF1) - C1-112 (IGF1) Always Below 1 Ω
C46-2 (IGF2) - C1-80 (IGF2) Always Below 1 Ω
C48-2 (IGF1) - C1-112 (IGF1) Always Below 1 Ω
C49-2 (IGF2) - C1-80 (IGF2) Always Below 1 Ω
C42-3 (IGT1) - C1-71 (IGT1) Always Below 1 Ω
C43-3 (IGT2) - C1-36 (IGT2) Always Below 1 Ω
C45-3 (IGT3) - C1-70 (IGT3) Always Below 1 Ω
C46-3 (IGT4) - C1-35 (IGT4) Always Below 1 Ω
C48-3 (IGT5) - C1-69 (IGT5) Always Below 1 Ω
C49-3 (IGT6) - C1-34 (IGT6) Always Below 1 Ω
C42-2 (IGF1) or C1-112 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C43-2 (IGF2) or C1-80 (IGF2) - Body ground and other terminals Always 10 kΩ or higher
C45-2 (IGF1) or C1-112 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C46-2 (IGF2) or C1-80 (IGF2) - Body ground and other terminals Always 10 kΩ or higher
C48-2 (IGF1) or C1-112 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C49-2 (IGF2) or C1-80 (IGF2) - Body ground and other terminals Always 10 kΩ or higher
C42-3 (IGT1) or C1-71 (IGT1) - Body ground and other terminals Always 10 kΩ or higher
C43-3 (IGT2) or C1-36 (IGT2) - Body ground and other terminals Always 10 kΩ or higher
C45-3 (IGT3) or C1-70 (IGT3) - Body ground and other terminals Always 10 kΩ or higher
C46-3 (IGT4) or C1-35 (IGT4) - Body ground and other terminals Always 10 kΩ or higher
C48-3 (IGT5) or C1-69 (IGT5) - Body ground and other terminals Always 10 kΩ or higher
C49-3 (IGT6) or C1-34 (IGT6) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - IGNITION COIL ASSEMBLY)
a.

Disconnect the semiconductor pwr integration ECU connector.


b.

Disconnect the ignition coil assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1G-3 - C42-1 (+B) Always Below 1 Ω
1G-3 - C43-1 (+B) Always Below 1 Ω
1G-3 - C45-1 (+B) Always Below 1 Ω
1G-3 - C46-1 (+B) Always Below 1 Ω
1G-3 - C48-1 (+B) Always Below 1 Ω
1G-3 - C49-1 (+B) Always Below 1 Ω
1G-3 or C42-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
1G-3 or C43-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
1G-3 or C45-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
1G-3 or C46-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
1G-3 or C48-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
1G-3 or C49-1 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SEMICONDUCTOR POWER INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR