Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › from 2018.09
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0095460 SMART ENTRY AND START SYSTEM(for Entry Function) U

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  TERMINALS OF ECU  


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B340022N26
4.99,0.292 5.417,0.521 0.427,0.229 1.552,0.26 1.979,0.49 0.427,0.229 3.25,0.292 3.677,0.521 0.427,0.229 1.667,0.292 2.125,0.49 0.458,0.198 10 false F10 5.115,0.323 5.573,0.521 0.458,0.198 10 false F13 3.365,0.323 3.823,0.521 0.458,0.198 10 false F12

a.

Disconnect the F13 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
F13-11 (E) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F13-10 (+B) - F13-11 (E) Input GR - W-B Power supply Always 11 to 14 V -


c.

Reconnect the F13 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
F10-3 (IG1D) - F13-11 (E) Output G - W-B IG power supply Engine switch off → on (IG) Below 1 V → 11 to 14 V -
F13-4 (CLG1) - F13-11 (E) Output SB*1 - W-B
P*2 - W-B
Output to driver door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*3)


Pulse generation
(See waveform 1)
Overhead + Driver Side (key diagnostic mode)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*3)


Pulse generation
(See waveform 2)
F13-4 (CLG1) - F13-11 (E) Input SB*1 - W-B
P*2 - W-B
Input to driver door lock sensor
(front door outside handle assembly (for driver door) lock sensor on signal is sent to the certification ECU (smart key ECU assembly))
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*3)

5.

Driver door lock sensor not touched → touched


Pulse generation
(See waveform 8)
D-Door Trigger Switch
F13-4 (CLG1) - F13-11 (E) Input SB*1 - W-B
P*2 - W-B
Input to driver door unlock sensor
(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Driver door unlock sensor not touched → touched


Pulse generation
(See waveform 9)
D-Door Touch Sensor
F13-3 (CG1B) - F13-11 (E) Output R*1 - W-B
L*2 - W-B
Output to driver door electrical key antenna (terminal on opposite side of component from CLG1 output terminal) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*3)


Pulse generation
(See waveform 1)
Overhead + Driver Side (key diagnostic mode)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*3)


Pulse generation
(See waveform 2)
F13-2 (CLG2) - F13-11 (E) Output P*1 - W-B
SB*2 - W-B
Output to front passenger door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*3)


Pulse generation
(See waveform 1)
Overhead + Passenger Side (key diagnostic mode)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*3)


Pulse generation
(See waveform 2)
F13-2 (CLG2) - F13-11 (E) Input P*1 - W-B
SB*2 - W-B
Input to front passenger door lock sensor
(front door outside handle assembly (for front passenger door) lock sensor on signal is sent to the certification ECU (smart key ECU assembly))
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*3)

5.

Front passenger door lock sensor not touched → touched


Pulse generation
(See waveform 8)
P-Door Trigger Switch
F13-2 (CLG2) - F13-11 (E) Input P*1 - W-B
SB*2 - W-B
Input to front passenger door unlock sensor
(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Front passenger door unlock sensor not touched → touched


Pulse generation
(See waveform 9)
P-Door Touch Sensor
F13-1 (CG2B) - F13-11 (E) Output L*1 - W-B
R*2 - W-B
Output to front passenger door electrical key antenna (terminal on opposite side of component from CLG2 output terminal) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*3)


Pulse generation
(See waveform 1)
Overhead + Passenger Side (key diagnostic mode)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*3)


Pulse generation
(See waveform 2)
F13-21 (CLG5) - F13-11 (E) Output SB - W-B Output to No. 1 indoor electrical key antenna assembly (front floor) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


Pulse generation
(See waveform 3)
Overhead + Front Room (key diagnostic mode)
F13-20 (CG5B) - F13-11 (E) Output GR - W-B Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG5 output terminal) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


Pulse generation
(See waveform 3)
Overhead + Front Room (key diagnostic mode)
F12-5 (TSW5) - F13-11 (E) Input P - W-B Back door opener switch assembly (open switch) signal input Back door opener switch assembly (open switch) off → on Pulse generation
(See waveform 5)
Tr/B-Door Unlock SW
F12-13 (TSW6) - F13-11 (E) Input L - W-B Back door opener switch assembly (lock switch) signal input Back door opener switch assembly (lock switch) off → on Pulse generation
(See waveform 5)
Tr/B-Door Lock SW
F12-15 (CLG6) - F13-11 (E) Output W - W-B Output to No. 2 indoor electrical key antenna assembly (rear floor) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


Pulse generation
(See waveform 3)
Overhead + Rear Room (key diagnostic mode)
F12-14 (CG6B) - F13-11 (E) Output B - W-B Output to No. 2 indoor electrical key antenna assembly (rear floor) (terminal on opposite side of component from CLG6 output terminal) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


Pulse generation
(See waveform 3)
Overhead + Rear Room (key diagnostic mode)
F12-4 (CLG7) - F13-11 (E) Output R - W-B Output to No. 3 indoor electrical key antenna assembly (inside luggage compartment) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


Pulse generation
(See waveform 3)
Luggage + Back Door (inside) (key diagnostic mode)
F12-3 (CG7B) - F13-11 (E) Output Y - W-B Output to No. 3 indoor electrical key antenna assembly (inside luggage compartment) (terminal on opposite side of component from CLG7 output terminal) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


Pulse generation
(See waveform 3)
Luggage + Back Door (inside) (key diagnostic mode)
F12-18 (RCO) - F13-11 (E) Output G - W-B Output to smart door control receiver assembly
(Power supply for smart door control receiver assembly. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation
(See waveform 6)
-
F12-19 (CSEL) - F13-11 (E) Output GR - W-B Communication channel switching circuit Procedure:
1.

Engine switch off

2.

All doors closed


Below 1 V → pulse generation -
F12-20 (RDAM) - F13-11 (E) Input P - W-B Smart door control receiver assembly verifies data received from electrical key transmitter sub-assembly.
Smart door control receiver assembly sends data from electrical key transmitter sub-assembly to certification ECU (smart key ECU assembly) (Smart door control receiver assembly intermittently grounds 12 V signal from certification ECU (smart key ECU assembly)).
Proceed:
1.

Engine switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation
(See waveform 7)
-
F12-2 (CLG8) - F13-11 (E) Output BE - W-B Output to electrical key antenna (outside luggage compartment) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on


Pulse generation
(See waveform 4)
Overhead + Back Door (key diagnostic mode)
F12-1 (CG8B) - F13-11 (E) Output G - W-B Output to electrical key antenna (outside luggage compartment) (terminal on opposite side of component from CLG8 output terminal) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on


Pulse generation
(See waveform 4)
Overhead + Back Door (key diagnostic mode)

*1: for LHD

*2: for RHD

*3: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK



e.
B340872N01
0.188,1.042 0.646,1.24 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 1.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Tester Connection F13-4 (CLG1) - F13-11 (E)
F13-3 (CG1B) - F13-11 (E)
F13-2 (CLG2) - F13-11 (E)
F13-1 (CG2B) - F13-11 (E)
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)



*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK



f.
B340873N01
0.177,1.021 0.635,1.219 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 2.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Tester Connection F13-4 (CLG1) - F13-11 (E)
F13-3 (CG1B) - F13-11 (E)
F13-2 (CLG2) - F13-11 (E)
F13-1 (CG2B) - F13-11 (E)
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)



*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK



g.
B340874C02
0.188,1.042 0.646,1.24 0.458,0.198 10 false GND 1.01,1.917 1.469,2.115 0.458,0.198 10 false *a 2.135,1.938 2.594,2.135 0.458,0.198 10 false *b
*a For 30 seconds after closing any door using the door outside handle
*b 30 seconds or more have elapsed after closing any door using the door outside handle


Using an oscilloscope, check waveform 3.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 3 (Reference)
Item Content
Tester Connection F13-21 (CLG5) - F13-11 (E)
F13-20 (CG5B) - F13-11 (E)
F12-15 (CLG6) - F13-11 (E)
F12-14 (CG6B) - F13-11 (E)
F12-4 (CLG7) - F13-11 (E)
F12-3 (CG7B) - F13-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle




h.
B340876N01
0.177,1.042 0.635,1.24 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 4.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 4 (Reference)
Item Content
Tester Connection F12-2 (CLG8) - F13-11 (E)
F12-1 (CG8B) - F13-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on




i.
B251023C09
1.333,0.49 1.99,0.125 1.99,0.125 2.208,0.125 false 1.99,0.135 1.74,0.51 false 0.198,1.198 0.531,1.396 0.333,0.198 10 false GND 2.25,0.031 2.427,0.208 0.177,0.177 10 false *a
*a Checking for switch on signal at short intervals


Using an oscilloscope, check waveform 5.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 5 (Reference)
Item Content
Tester Connection F12-5 (TSW5) - F13-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Back door opener switch assembly (open switch) off → on

Waveform 5 (Reference)
Item Content
Tester Connection F12-13 (TSW6) - F13-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Back door opener switch assembly (lock switch) off → on


j.
B251178C12
0.198,1 0.531,1.198 0.333,0.198 10 GND 1.01,1.885 1.198,2.042 0.188,0.156 10 *a 2.021,1.885 2.208,2.042 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 6.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 6 (Reference)
Item Content
Tester Connection F12-18 (RCO) - F13-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed




k.
B251177C12
0.208,1 0.542,1.198 0.333,0.198 10 GND 1.021,1.896 1.208,2.052 0.188,0.156 10 *a 2.188,1.906 2.375,2.063 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 7.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 7 (Reference)
Item Content
Tester Connection F12-20 (RDAM) - F13-11 (E)
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed




l.
B340877C02
0.188,1.042 0.646,1.24 0.458,0.198 10 false GND 0.677,1.917 1.135,2.115 0.458,0.198 10 false *a 1.646,2 1.969,2.156 0.323,0.156 10 false *b 2.615,1.917 3.073,2.115 0.458,0.198 10 false *a
*a Lock sensor not touched
*b Lock sensor touched


Using an oscilloscope, check waveform 8.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 8 (Reference)
Item Content
Tester Connection F13-4 (CLG1) - F13-11 (E)
Tool Setting 5 V/DIV., 40 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)

5.

Driver door lock sensor not touched → touched



Waveform 8 (Reference)
Item Content
Tester Connection F13-2 (CLG2) - F13-11 (E)
Tool Setting 5 V/DIV., 40 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)

5.

Front passenger door lock sensor not touched → touched



*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK



m.
B340879C02
0.177,1.052 0.635,1.25 0.458,0.198 10 false GND 0.344,1.906 0.802,2.104 0.458,0.198 10 false *a 2.115,1.906 2.573,2.104 0.458,0.198 10 false *a 1.229,1.969 1.667,2.167 0.438,0.198 10 false *b
*a Unlock sensor not touched
*b Unlock sensor touched


Using an oscilloscope, check waveform 9.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 9 (Reference)
Item Content
Tester Connection F13-4 (CLG1) - F13-11 (E)
Tool Setting 5 V/DIV., 40 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Driver door unlock sensor not touched → touched



Waveform 9 (Reference)
Item Content
Tester Connection F13-2 (CLG2) - F13-11 (E)
Tool Setting 5 V/DIV., 40 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Front passenger door unlock sensor not touched → touched





CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


B357833C01
4.99,3.521 5.396,3.792 0.406,0.271 1.427,4.823 1.833,5.094 0.406,0.271 4.083,4.802 4.49,5.073 0.406,0.271 5.573,4.927 5.979,5.198 0.406,0.271 1.354,6.396 1.76,6.667 0.406,0.271 4.865,6.396 5.271,6.667 0.406,0.271 6.469,4.927 6.875,5.198 0.406,0.271 3.458,7.969 3.865,8.24 0.406,0.271 1.792,3.521 2.198,3.792 0.406,0.271 2.25,0.25 2.083,0.25 2.083,0.25 2.083,0.604 false 2.5,2.083 2.25,2.083 2.25,2.083 2.167,2.083 false 2.5,1.583 2.25,1.583 2.25,1.583 2.167,1.583 false 2.021,1.583 1.667,1.583 1.667,1.583 1.667,2.417 false 2.021,2.083 1.75,2.083 1.75,2.083 1.667,2.083 false 4.833,0.198 4.667,0.198 4.667,0.198 4.667,0.552 false 0.125,0.094 0.5,0.333 0.375,0.24 12 false *A 0.552,1.052 0.75,1.25 0.198,0.198 10 false 4H 0.552,1.802 0.75,2 0.198,0.198 10 false 4F 0.563,2.24 0.76,2.438 0.198,0.198 10 false 4K 0.833,2.51 1.031,2.708 0.198,0.198 10 false 4L 2.365,0.156 2.563,0.354 0.198,0.198 10 false *1 2.563,1.479 2.99,1.719 0.427,0.24 10 false F19 2.583,1.969 2.958,2.25 0.375,0.281 10 false F18 1.604,2.448 1.802,2.646 0.198,0.198 10 false *a 4.917,0.083 5.167,0.25 0.25,0.167 10 false MB 6.458,0.906 6.656,1.104 0.198,0.198 10 false 4D 6.458,1.74 6.656,1.938 0.198,0.198 10 false 4A 1.875,3.573 2.396,3.802 0.521,0.229 10 false F18 5.083,3.573 5.771,3.938 0.688,0.365 10 false F19 1.552,4.885 1.833,5.083 0.281,0.198 10 false 4H 4.208,4.854 4.406,5.052 0.198,0.198 10 false 4F 5.698,4.99 6.021,5.208 0.323,0.219 10 false 4K 1.479,6.448 1.677,6.646 0.198,0.198 10 false 4D 4.99,6.448 5.188,6.646 0.198,0.198 10 false 4A 6.604,4.99 6.802,5.188 0.198,0.198 10 false 4L 3.563,8.021 3.844,8.271 0.281,0.25 10 false MB
*A Main Body ECU (Multiplex Network Body ECU) with 2 Connectors - -
*1 Main Body ECU (Multiplex Network Body ECU) - -
*a 2 Connectors - -


B357834C01
1.083,3.479 1.5,3.75 0.417,0.271 3.594,3.5 4.01,3.771 0.417,0.271 5.917,3.479 6.333,3.75 0.417,0.271 1.417,4.833 1.833,5.104 0.417,0.271 4.042,4.833 4.458,5.104 0.417,0.271 5.563,4.906 5.979,5.177 0.417,0.271 1.385,6.396 1.802,6.667 0.417,0.271 4.844,6.396 5.26,6.667 0.417,0.271 6.438,4.906 6.854,5.177 0.417,0.271 3.417,7.958 3.833,8.229 0.417,0.271 2.083,0.604 2.083,0.25 2.083,0.25 2.25,0.25 false 2.167,1.083 2.583,1.083 false 2.167,1.583 2.583,1.583 false 2.167,2.083 2.583,2.083 false 1.667,1.583 2.021,1.583 false 1.667,2.083 2.021,2.083 false 1.667,2.5 1.667,1.083 1.667,1.083 2.021,1.083 false 4.583,0.552 4.583,0.198 4.583,0.198 4.75,0.198 false 0.156,0.135 0.531,0.375 0.375,0.24 12 false *A 0.552,1.052 0.833,1.219 0.281,0.167 10 false 4H 0.552,1.823 0.833,1.99 0.281,0.167 10 false 4F 0.563,2.25 0.844,2.417 0.281,0.167 10 false 4K 0.833,2.521 1.115,2.688 0.281,0.167 10 false 4L 2.302,0.188 2.615,0.385 0.313,0.198 10 false *1 1.594,2.531 1.906,2.729 0.313,0.198 10 false *a 2.646,1.01 3.104,1.26 0.458,0.25 10 false F20 2.656,1.51 3.104,1.771 0.448,0.26 10 false F19 2.656,2.01 3.094,2.24 0.438,0.229 10 false F18 4.813,0.125 5.156,0.344 0.344,0.219 10 false MB 6.458,0.927 6.823,1.094 0.365,0.167 10 false 4D 6.458,1.75 6.823,1.917 0.365,0.167 10 false 4A 1.177,3.531 1.458,3.698 0.281,0.167 10 false F18 3.688,3.563 4.219,3.823 0.531,0.26 10 false F19 6.021,3.542 6.479,3.781 0.458,0.24 10 false F20 1.531,4.896 1.813,5.063 0.281,0.167 10 false 4H 4.177,4.896 4.458,5.063 0.281,0.167 10 false 4F 5.688,4.979 5.969,5.146 0.281,0.167 10 false 4K 3.521,8.021 3.885,8.25 0.365,0.229 10 false MB 1.521,6.458 1.802,6.625 0.281,0.167 10 false 4D 4.969,6.458 5.25,6.625 0.281,0.167 10 false 4A 6.573,4.969 6.854,5.135 0.281,0.167 10 false 4L
*A Main Body ECU (Multiplex Network Body ECU) with 3 Connectors - -
*1 Main Body ECU (Multiplex Network Body ECU) - -
*a 3 Connectors - -


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
MB-11 (GND1) - Body ground - - Ground Always Below 1 Ω -
MB-31 (BECU) - Body ground Input - Battery power supply (for CPU) Always 11 to 14 V -
F19-6 (FLCY) - Body ground Input SB - Body ground Front door LH courtesy light switch input Front door LH closed → open 10 kΩ or higher → Below 1 Ω FL Door Courtesy SW
F19-27 (FRCY) - Body ground Input L - Body ground Front door RH courtesy light switch input Front door RH closed → open 10 kΩ or higher → Below 1 Ω FR Door Courtesy SW
MB-13 (LCTY) - Body ground Input - Rear door LH courtesy light switch input Rear door LH closed → open 10 kΩ or higher → Below 1 Ω RL Door Courtesy SW
MB-2 (RCTY) - Body ground Input - Rear door RH courtesy light switch input Rear door RH closed → open 10 kΩ or higher → Below 1 Ω RR Door Courtesy SW
4H-33 (BCTY) - Body ground Input LA-Y - Body ground Back door courtesy light switch input Back door closed → open 10 kΩ or higher → Below 1 Ω Back Door Courtesy SW
F18-27 (GCTY) - Body ground Input R - Body ground Glass hatch courtesy light switch input Back door glass closed → open 10 kΩ or higher → Below 1 Ω Glass Hatch Courtesy Switch


d.

Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


e.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
4D-10 (LSFL) - Body ground Input GR - Body ground Front door LH unlock detection switch input Front door LH locked → unlocked Pulse generation
(See waveform 1)
FL Door Lock Pos
4D-26 (LSFR) - Body ground Input Y - Body ground Front door RH unlock detection switch input Front door RH locked → unlocked Pulse generation
(See waveform 1)
FR Door Lock Pos
4H-34 (LSWL) - Body ground Input V - Body ground Rear door LH unlock detection switch input Rear door LH locked → unlocked Pulse generation
(See waveform 1)
RL-Door Lock Pos SW
F18-2 (LSWR) - Body ground Input LG - Body ground Rear door RH unlock detection switch input Rear door RH locked → unlocked Pulse generation
(See waveform 1)
RR-Door Lock Pos SW
F19-6 (FLCY) - Body ground Input GR - Body ground Front door LH courtesy light switch input Front door LH closed → open Pulse generation
(See waveform 2)
FL Door Courtesy SW
F19-27 (FRCY) - Body ground Input L - Body ground Front door RH courtesy light switch input Front door RH closed → open Pulse generation
(See waveform 2)
FR Door Courtesy SW
4H-36 (LCTY) - Body ground Input SB - Body ground Rear door LH courtesy light switch input Rear door LH closed → open Pulse generation
(See waveform 2)
RL Door Courtesy SW
4D-30 (RCTY) - Body ground Input LG - Body ground Rear door RH courtesy light switch input Rear door RH closed → open Pulse generation
(See waveform 2)
RR Door Courtesy SW
4H-33 (BCTY) - Body ground Input LA-Y - Body ground Back door courtesy light switch input Back door closed → opened Pulse generation
(See waveform 2)
Back Door Courtesy SW
F18-27 (GCTY) - Body ground Input R - Body ground Glass hatch courtesy light switch input Back door glass closed → open Pulse generation
(See waveform 2)
Glass Hatch Courtesy Switch
4F-30 (BZR) - Body ground* Output B - Body ground Wireless buzzer signal output Procedure:
1.

Engine switch off

2.

All doors closed

3.

Lock switch of electrical key transmitter sub-assembly not pressed → pressed


Below 1 V → pulse generation -

*: w/ Wireless Door Lock Buzzer Answer-back Function



f.
B340769C02
0.219,1.583 0.552,1.75 0.333,0.167 10 false GND 1.25,1.917 1.5,2.083 0.25,0.167 10 false *a 2.219,1.917 2.469,2.083 0.25,0.167 10 false *b
*a Door locked
*b Door unlocked


Using an oscilloscope, check waveform 1.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Tester Connection 4D-10 (LSFL) - Body ground
4D-26 (LSFR) - Body ground
4H-34 (LSWL) - Body ground
F18-2 (LSWR) - Body ground
Tool Setting 2 V/DIV., 200 ms/DIV.
Condition Door locked → unlocked


g.
B340769C03
0.219,1.583 0.552,1.75 0.333,0.167 10 false GND 1.25,1.917 1.5,2.083 0.25,0.167 10 false *a 2.219,1.917 2.469,2.083 0.25,0.167 10 false *b
*a Door closed
*b Door open


Using an oscilloscope, check waveform 2.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Tester Connection F19-6 (FLCY) - Body ground
F19-27 (FRCY) - Body ground
4H-36 (LCTY) - Body ground
4D-30 (RCTY) - Body ground
4H-33 (BCTY) - Body ground
F18-27 (GCTY) - Body ground
Tool Setting 2 V/DIV., 200 ms/DIV.
Condition Door closed → opened