Home › Suspension › REAR SUSPENSION › REAR COIL SPRING › from 2018.09
RM3160E _53 Suspension _019690 REAR SUSPENSION _0109431 REAR COIL SPRING A

REAR SUSPENSION  REAR COIL SPRING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 48258C 1.INSTALL REAR LOWER COIL SPRING INSULATOR

a.

Install the rear lower coil spring insulator to the rear No. 2 suspension arm assembly.


Hide 48259A 2.INSTALL REAR UPPER COIL SPRING INSULATOR

a.

Install the rear upper coil spring insulator.


Hide 48231B 3.INSTALL REAR COIL SPRING

a.
C199855C01
0.406,1.781 1.104,1.781 true 0.5,3.281 1.198,3.281 true 0.323,3.177 0.635,3.333 0.313,0.156 10 false *a 0.25,1.688 0.563,1.844 0.313,0.156 10 false *a
*a Identification Mark


Set the rear coil spring to the rear No. 2 suspension arm assembly.

NOTICE:

Set the rear coil spring so that the identification mark is positioned as shown in the illustration.



b.
C293826C02
1.26,1.635 1.688,1.635 true 0.198,1.917 0.344,1.917 true 1.708,1.521 1.99,1.719 0.281,0.198 10 true *a 0.031,1.833 0.344,1.99 0.313,0.156 10 false *b 3.042,1.594 3.198,1.792 0.156,0.198 10 true A 0.229,1.594 0.365,1.792 0.135,0.198 10 true B
*a Wooden Block
*b Jack


Using a jack and wooden block, slowly jack up the rear No. 2 suspension arm assembly and then temporarily install the rear No. 2 suspension arm assembly to the rear axle assembly with the bolt (B) and nut.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

CAUTION:

Do not jack up the rear No. 2 suspension arm assembly too high as the vehicle may fall.


NOTICE:
·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Insert the bolt with the threaded end facing the front of the vehicle.




Hide 48802 4.INSTALL REAR STABILIZER LINK SUB-ASSEMBLY

a.
C293825N01
1.885,1.635 2.042,1.833 0.156,0.198 10 true A 2.552,1.667 2.708,1.865 0.156,0.198 10 true A 2.531,0.781 2.688,0.979 0.156,0.198 10 true B

Install the rear stabilizer link sub-assembly to the rear stabilizer bar with the nut (B).

Torque:
90 N*m (918 kgf*cm, 66 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



b.

Install the rear stabilizer link sub-assembly to the rear No. 2 suspension arm assembly with the 2 nuts (A).

Torque:
82 N*m (836 kgf*cm, 60 ft.*lbf)


Hide 5.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 48740F 6.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

Hide 7.INSPECT AND ADJUST REAR WHEEL ALIGNMENT