Home › Engine / Hybrid System › 2GR-FKS (INTAKE / EXHAUST) › INTAKE MANIFOLD › 2020.02–2020.11
RM37A0E _51 Engine / Hybrid System _086854 2GR-FKS INTAKE / EXHAUST _0416458 INTAKE MANIFOLD A

2GR-FKS INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during intake manifold removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Replacement of fuel injector assembly

·

Replacement of fuel pressure sensor (fuel delivery pipe with sensor assembly)

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 4.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 53808A 5.REMOVE FENDER SPLASH SHIELD SUB-ASSEMBLY REAR LH

Hide 53807A 6.REMOVE FENDER SPLASH SHIELD SUB-ASSEMBLY REAR RH

HINT:

Perform the same procedure as for the LH side.


Hide 53892C 7.REMOVE FRONT FENDER SPLASH SHIELD SEAL FRONT LH

Hide 53891C 8.REMOVE FRONT FENDER SPLASH SHEILD SEAL FRONT RH

HINT:

Perform the same procedure as for the LH side.


Hide 9.REMOVE FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY LH

Hide 53607B 10.REMOVE FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 55704B 11.REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 22030 12.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 11209 13.REMOVE V-BANK COVER SUB-ASSEMBLY

Hide 12261 14.DISCONNECT VENTILATION HOSE

a.
A457814

Slide the clip and disconnect the ventilation hose from the intake air surge tank assembly.


Hide 25860 15.DISCONNECT PURGE VALVE (PURGE VSV)

a.
A457794

Disconnect the No. 1 fuel vapor feed hose from the intake air surge tank assembly.


b.

Remove the bolt and disconnect the purge valve (purge VSV) from the intake air surge tank assembly.


Hide 17126 16.REMOVE NO. 2 SURGE TANK STAY

a.
A454229

Remove the 2 bolts and No. 2 surge tank stay from the intake air surge tank assembly and camshaft housing RH.


Hide 17190 17.REMOVE INTAKE AIR SURGE TANK ASSEMBLY

a.
A454230

Disconnect the No. 1 vacuum switching valve assembly (for ACIS) connector.


b.

Disengage the 2 clamps to disconnect the vacuum hose sub-assembly from the intake air surge tank assembly.


c.
A454231C01
2.677,1.583 3.031,1.75 3.031,1.75 3.031,1.948 true 1.604,1.302 1.604,1.75 true 1.094,0.875 1.51,0.531 1.51,0.531 1.75,0.531 true 2.948,1.948 3.135,2.167 0.188,0.219 10 true *1 1.813,0.438 2,0.625 0.188,0.188 10 true *2 1.552,1.792 1.75,1.969 0.198,0.177 10 true *3
*1 Vacuum Hose Sub-assembly
*2 Vacuum Hose
*3 No. 2 Air Tube


Disengage the 2 clamps to disconnect the vacuum hose sub-assembly from the intake air surge tank assembly.


d.

Disengage the clamp to disconnect the vacuum hose from the intake air surge tank assembly.


e.

Disengage the clamp to disconnect the No. 2 air tube from the intake air surge tank assembly.


f.
A454232

Remove the 5 bolts, 2 nuts and intake air surge tank assembly from the intake manifold.


Hide 17176 18.REMOVE AIR SURGE TANK TO INTAKE MANIFOLD GASKET

a.
A370410

Remove the air surge tank to intake manifold gasket from the intake air surge tank assembly.


Hide 11254 19.REMOVE NO. 1 V-BANK COVER BRACKET

HINT:

Perform this procedure only when replacement of the No. 1 V-bank cover bracket is necessary.


a.
A370409

Remove the 2 No. 1 V-bank cover brackets from the intake air surge tank assembly.


Hide 12327A 20.REMOVE NO. 2 ENGINE MOUNTING STAY RH

a.
A454233

Remove the bolt, 2 nuts and No. 2 engine mounting stay RH from the engine mounting insulator sub-assembly RH and rear engine mounting stay RH.


Hide 12327 21.REMOVE REAR ENGINE MOUNTING STAY RH

a.
A454234

Remove the bolt and disconnect the engine wire from the rear engine mounting stay RH.


b.
A454235

Remove the bolt and rear engine mounting stay RH from the intake manifold.


Hide 23800 23.REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY

Hide 23807V 24.REMOVE NO. 1 DELIVERY PIPE SPACER

Hide 23291 25.REMOVE INJECTOR VIBRATION INSULATOR

Hide 17111 26.REMOVE INTAKE MANIFOLD

a.
A454246

Remove the 4 bolts, 4 nuts and intake manifold from the cylinder head sub-assembly.


Hide 17177 27.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

a.
A454247

Remove the 2 No. 1 intake manifold to head gaskets from each cylinder head sub-assembly.


Hide 28.REMOVE STUD BOLT

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.


a.
A370417

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the intake manifold.