Home › Engine / Hybrid System › 2GR-FKS (INTAKE / EXHAUST) › EXHAUST MANIFOLD
RM37A0E _51 Engine / Hybrid System _086854 2GR-FKS INTAKE / EXHAUST _0416461 EXHAUST MANIFOLD A

2GR-FKS INTAKE / EXHAUST  EXHAUST MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during exhaust manifold assembly RH (TWC: Front Catalyst) and exhaust manifold assembly LH (TWC: Front Catalyst) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of air fuel ratio sensor

·

Gas leak from exhaust system is repaired


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



PROCEDURE

Hide 53852B 1.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851D 2.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 51441 3.REMOVE NO. 1 ENGINE UNDER COVER

Hide 17410 4.REMOVE FRONT EXHAUST PIPE ASSEMBLY

a.
A455883

Disengage the 2 wire harness clamps.


b.

Disconnect the heated oxygen sensor (for Bank 1) connector.


c.
A454258

Disengage the 2 wire harness clamps.


d.

Disconnect the heated oxygen sensor (for Bank 2) connector.


e.
A454259

Remove the 2 bolts, 4 nuts, 2 compression springs and front exhaust pipe assembly from the exhaust manifold assembly RH (TWC: Front Catalyst), exhaust manifold assembly LH (TWC: Front Catalyst) and center exhaust pipe assembly (TWC: Rear Catalyst).


f.

Remove the 3 gaskets from the front exhaust pipe assembly.


Hide 37100 5.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 17118 6.REMOVE MANIFOLD STAY

a.
A454260

Remove the bolt, nut and manifold stay from the exhaust manifold RH (TWC: Front Catalyst) and rear engine mounting bracket.


Hide 17140 7.REMOVE EXHAUST MANIFOLD ASSEMBLY RH (TWC: Front Catalyst)

a.
A454261

Disconnect the air fuel ratio sensor (for Bank 1) connector.


b.

Disengage the wire harness clamp.


c.
A454262

Remove the 4 nuts and exhaust manifold assembly RH (TWC: Front Catalyst) from the cylinder head sub-assembly RH.


Hide 17173 8.REMOVE EXHAUST MANIFOLD TO HEAD GASKET (for Bank 1)

a.
A454263

Remove the exhaust manifold to head gasket (for Bank 1) from the cylinder head sub-assembly RH.


Hide 89467C 9.REMOVE AIR FUEL RATIO SENSOR (for Bank 1)

Hide 11209 10.REMOVE V-BANK COVER SUB-ASSEMBLY

Hide 89467B 11.REMOVE AIR FUEL RATIO SENSOR (for Bank 2)

Hide 89439D 12.REMOVE NO. 1 SENSOR BRACKET

a.
A454264

Remove the bolt and No. 1 sensor bracket from the cylinder head sub-assembly.


Hide 17168 13.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A454265

Remove the 3 bolts and No. 2 exhaust manifold heat insulator from the exhaust manifold assembly LH (TWC: Front Catalyst).


Hide 17119 14.REMOVE NO. 2 MANIFOLD STAY

a.
A454266

Remove the bolt, nut and No. 2 manifold stay from the exhaust manifold assembly LH (TWC: Front Catalyst) and cylinder block sub-assembly.


Hide 17150 15.REMOVE EXHAUST MANIFOLD ASSEMBLY LH (TWC: Front Catalyst)

a.
A454267

Remove the 4 nuts and exhaust manifold assembly LH (TWC: Front Catalyst).


Hide 17173A 16.REMOVE EXHAUST MANIFOLD TO HEAD GASKET (for Bank 2)

a.
A454268

Remove the exhaust manifold to head gasket (for Bank 2) from the cylinder head sub-assembly.


Hide 17.REMOVE STUD BOLT

HINT:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A454276

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold assembly LH (TWC: Front Catalyst).


b.
A454269

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold assembly RH (TWC: Front Catalyst).