Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Front Door) › 2020.02–2020.11
RM37A0E _59 Vehicle Exterior _086899 WINDOW / GLASS _0416692 POWER WINDOW REGULATOR MOTOR(for Front Door) A

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Front Door)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during power window regulator motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Front door window regulator sub-assembly LH*

·

Front door window regulator sub-assembly RH*

·

Front door glass sub-assembly LH*

·

Front door glass sub-assembly RH*

·

Front door glass run LH*

·

Front door glass run RH*


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Front door window regulator sub-assembly LH*

·

Front door window regulator sub-assembly RH*

·

Front door glass sub-assembly LH*

·

Front door glass sub-assembly RH*

·

Front door glass run LH*

·

Front door glass run RH*


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 58441L 1.REMOVE BATTERY SERVICE HOLE COVER (for HV Model)

Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 67492A 3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

Hide 4.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Hide 5.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Hide 69278B 6.REMOVE FRONT DOOR INSIDE HANDLE BEZEL

Hide 81230N 7.REMOVE COURTESY LIGHT ASSEMBLY

Hide 67602 8.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 67869J 9.REMOVE FRONT DOOR WEATHERSTRIP CLIP

Hide 67832 10.REMOVE FRONT DOOR SERVICE HOLE COVER

Hide 68102 11.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

Hide 12.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY

Hide 85720D 13.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY

a.
B564588

Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly.