Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2020.02–2020.11
RM37A0E _59 Vehicle Exterior _086885 DOOR / HATCH _0418597 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Outer rear view mirror assembly LH*

·

Outer rear view mirror assembly RH*


Side television camera view adjustment Panoramic View Monitor System (Click here)
Replacement or removal and installation of 2 or more parts:
·

Front television camera assembly, radiator grille sub-assembly or front bumper assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment Panoramic View Monitor System (Click here)
·

Front door window regulator sub-assembly LH*

·

Front door window regulator sub-assembly RH*

·

Front door glass sub-assembly LH*

·

Front door glass sub-assembly RH*

·

Front door glass run LH*

·

Front door glass run RH*


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Outer rear view mirror assembly LH*

·

Outer rear view mirror assembly RH*


Side television camera view adjustment Panoramic View Monitor System (Click here)
Replacement or removal and installation of 2 or more parts:
·

Front television camera assembly, radiator grille sub-assembly or front bumper assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment Panoramic View Monitor System (Click here)
·

Front door window regulator sub-assembly LH*

·

Front door window regulator sub-assembly RH*

·

Front door glass sub-assembly LH*

·

Front door glass sub-assembly RH*

·

Front door glass run LH*

·

Front door glass run RH*


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B401522

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 58441L 2.REMOVE BATTERY SERVICE HOLE COVER (for HV Model)

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for 2GR-FKS:

Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>REMOVAL

for A25A-FXS, A25B-FXS:

Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>REMOVAL

CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If an airbag deploys for any reason, it may cause a serious injury.



Hide 67492A 4.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

a.
B563755

Disengage the clip and guide to remove the front door lower frame bracket garnish.


Hide 5.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

a.
B566536C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the front door trim board sub-assembly as shown in the illustration.


b.
B566537

Using a moulding remover, disengage the 2 clips, 4 claws and 5 guides as shown in the illustration.


c.

Disconnect each connector to remove the multiplex network master switch assembly with front door upper armrest base panel.


Hide 6.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

a.
B566539C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the front door trim board sub-assembly as shown in the illustration.


b.
B566540

Using a moulding remover, disengage the 2 clips, 6 claws and 5 guides as shown in the illustration.


c.

Disconnect the connector to remove the power window regulator switch assembly with front door upper armrest base panel.


Hide 69278B 7.REMOVE FRONT DOOR INSIDE HANDLE BEZEL

a.
B563762

Using a moulding remover, disengage the 3 claws to remove the front door inside handle bezel as shown in the illustration.


Hide 81230N 8.REMOVE COURTESY LIGHT ASSEMBLY

Hide 67602 9.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B563764C01
0.76,0.781 1.177,1.135 true 0.552,0.688 0.75,0.875 0.198,0.188 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disengage the claw as shown in the illustration.


b.
B563766

Remove the 3 screws.


c.
B563767C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 10 clips as shown in the illustration.


d.
B563768C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 4 claws and guide as shown in the illustration.


e.

w/ Illumination:

i.
B563770

Disengage the clamp.


ii.

Disconnect the connector.



f.

w/ Seat Memory Switch:

i.
B563771

Disconnect the connector.



g.
B563772C01
2.146,1.021 2.563,0.604 true 2.083,1.677 2.083,1.385 true 2.573,0.49 2.792,0.667 0.219,0.177 10 true *1 2,1.688 2.219,1.875 0.219,0.188 10 true *2
*1 Front Door Inside Lock/Unlock Knob Locking Cable
*2 Front Door Lock Open Lever Remote Control Cable
V113147

Remove in this Direction


Disconnect the front door lock open lever remote control cable and front door inside lock/unlock knob locking cable as shown in the illustration to remove the front door trim board sub-assembly.


Hide 69206B 10.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B563774

Disengage the 3 claws to remove the front door inside handle sub-assembly.


Hide 74038C 11.REMOVE DOOR ARMREST COVER SUB-ASSEMBLY

a.
B563775C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claw to remove the door armrest cover sub-assembly as shown in the illustration.


Hide 84927 12.REMOVE SEAT MEMORY SWITCH (w/ Seat Memory Switch)

Hide 67664C 13.REMOVE DOOR FRAME GARNISH

a.
B563777C01
0,0 0,0 false
V113147

Remove in this Direction


Using a clip remover, disengage the clip.


b.

Disengage the 2 guides to remove the door frame garnish as shown in the illustration.


Hide 89430 14.REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Memory)

Hide 87964 15.REMOVE OUTER MIRROR INSTALL HOLE COVER

Hide 16.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER

Hide 68172A 17.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP

a.
B563779C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door inner glass weatherstrip as shown in the illustration.


Hide 67838A 18.REMOVE FRONT DOOR VENT SEAL

a.
B563781C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 3 guides to remove the front door vent seal from the front door inner glass weatherstrip as shown in the illustration.


Hide 67856D 19.REMOVE FRONT DOOR PANEL PROTECTOR

a.
B563783C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door panel protector as shown in the illustration.


Hide 86160 20.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

Hide 67869J 21.REMOVE FRONT DOOR WEATHERSTRIP CLIP

a.
B563785

Turn each front door weatherstrip clip 45 degrees as shown in the illustration and remove the 3 front door weatherstrip clips.


Hide 67832 22.REMOVE FRONT DOOR SERVICE HOLE COVER

a.
B563787

Disconnect the connector.


b.

Disengage the 6 clamps.


c.
B563788

Disengage the 5 clips and remove the front door service hole cover.


Hide 89860A 23.REMOVE SIDE AIRBAG SENSOR ASSEMBLY

Hide 68102 24.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

a.
B563789

Remove the hole plug.


b.

for Driver Side:

i.

Connect the power window regulator master switch assembly.



c.

for Front Passenger Side:

i.

Connect the power window regulator switch assembly.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


f.

Move the front door glass sub-assembly so that the door glass bolts can be seen.


g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

for Driver Side:

i.

Disconnect the power window regulator master switch assembly.



j.

for Front Passenger Side:

i.

Disconnect the power window regulator switch assembly.



k.
B563790

Remove the 2 bolts.

NOTICE:

After the bolts are removed, do not allow the front door glass sub-assembly to fall.



l.
B563791C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the front door glass sub-assembly as shown in the illustration.

NOTICE:

Do not damage the front door glass sub-assembly.



Hide 25.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.
B563793

Disconnect the connector.


b.

Remove the 7 nuts and front door window regulator assembly.


Hide 68151D 26.REMOVE FRONT DOOR GLASS RUN

a.
B563795

Remove the front door glass run.


Hide 67404F 27.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B563796C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the bolt.


b.

Disengage the guide and remove the front door rear lower frame sub-assembly as shown in the illustration.


Hide 69220 28.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B563798

Using a screwdriver, disengage the 2 claws as shown in the illustration.


b.
B563800

Using a screwdriver, disconnect the connector.


c.
B563802

Disengage the 2 claws and move the lever as shown in the illustration.


d.
B563804C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door outside handle assembly as shown in the illustration.


Hide 29.REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B563806

Remove the hole plug.


b.
B563807

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door lock cylinder assembly.

HINT:

The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



Hide 69217D 30.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B563808

Remove the hole plug.


b.
B563809

Using a T30 "TORX" socket wrench, loosen the screw.

HINT:

The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



c.

Disengage the 2 claws to remove the front door outside handle cover.


Hide 69241H 31.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B563810

Disengage the 2 claws and guide to remove the front door front outside handle pad.


Hide 69242E 32.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B563811

Disengage the claw and 3 guides to remove the front door rear outside handle pad.


Hide 69040A 33.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY

Hide 69202A 34.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.
B563812

Disengage the clamp.


b.
B563813

Using a T30 "TORX" socket wrench, remove the screw.


c.
B563814C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claw and guide to remove the front door outside handle frame sub-assembly as shown in the illustration.


Hide 69312 35.REMOVE FRONT DOOR LOCK OPEN ROD

a.
B563816C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the front door lock open rod as shown in the illustration.


Hide 75720 36.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

Hide 75756D 37.REMOVE FRONT DOOR WINDOW FRAME MOULDING

Hide 75754A 38.REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING

Hide 67496C 39.REMOVE FRONT DOOR FRONT LOWER FRAME UPPER COVER

Hide 75792 40.REMOVE DOOR WINDOW FRAME MOULDING CLIP

a.
B563818C01
0.396,1.344 1.177,0.792 true 0.188,1.271 0.5,1.427 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the door window frame moulding clip.


Hide 67001A 41.REMOVE FRONT DOOR PANEL CUSHION

a.
B563820

Disengage the claw to remove the front door panel cushion.


Hide 42.REMOVE FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY

Hide 75793 43.REMOVE FRONT DOOR UPPER OUTSIDE MOULDING PAD

Hide 67837B 44.REMOVE FRONT DOOR DUST PROOF SEAL

a.
B563821

Disengage the 3 claws to remove the 3 front door dust proof seals.


Hide 68620 45.REMOVE FRONT DOOR CHECK ASSEMBLY

a.
B563823C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt, 2 nuts and front door check assembly.


Hide 67862 46.REMOVE FRONT DOOR WEATHERSTRIP

a.
B563824

Using a clip remover, disengage the 24 clips and remove the front door weatherstrip.