Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Rear Door) › 2020.02–2020.11
RM37A0E _59 Vehicle Exterior _086899 WINDOW / GLASS _0416693 POWER WINDOW REGULATOR MOTOR(for Rear Door) A

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Rear Door)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during power window regulator motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Rear door window regulator sub-assembly LH*

·

Rear door window regulator sub-assembly RH*

·

Rear door glass sub-assembly LH*

·

Rear door glass sub-assembly RH*

·

Rear door glass run LH*

·

Rear door glass run RH*


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Rear door window regulator sub-assembly LH*

·

Rear door window regulator sub-assembly RH*

·

Rear door glass sub-assembly LH*

·

Rear door glass sub-assembly RH*

·

Rear door glass run LH*

·

Rear door glass run RH*


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 58441L 2.REMOVE BATTERY SERVICE HOLE COVER (for HV Model)

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Hide 69278C 5.REMOVE REAR DOOR INSIDE HANDLE BEZEL

Hide 67604 6.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 67872 7.DISCONNECT REAR DOOR WEATHERSTRIP

a.
B564593

Disconnect the rear door weatherstrip.


Hide 68174A 8.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

Hide 67225A 9.REMOVE QUARTER WINDOW UPPER STOP

Hide 67842E 10.REMOVE REAR DOOR SERVICE HOLE COVER

Hide 68152C 11.REMOVE REAR DOOR GLASS RUN

Hide 67408E 12.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

Hide 68104 13.REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Hide 14.REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY

Hide 85720E 15.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY

a.
B564594

Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly.