Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › 2020.02–2020.11
RM37A0E _59 Vehicle Exterior _086885 DOOR / HATCH _0418599 REAR DOOR A

DOOR / HATCH  REAR DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Rear door window regulator sub-assembly LH*

·

Rear door window regulator sub-assembly RH*

·

Rear door glass sub-assembly LH*

·

Rear door glass sub-assembly RH*

·

Rear door glass run LH*

·

Rear door glass run RH*


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Rear door window regulator sub-assembly LH*

·

Rear door window regulator sub-assembly RH*

·

Rear door glass sub-assembly LH*

·

Rear door glass sub-assembly RH*

·

Rear door glass run LH*

·

Rear door glass run RH*


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 58441L 2.REMOVE BATTERY SERVICE HOLE COVER (for HV Model)

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

a.
B564421C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the rear door trim board sub-assembly as shown in the illustration.


b.
B564422

Using a moulding remover, disengage the 2 clips, 2 claws and 5 guides as shown in the illustration.


c.

Disconnect the connector to remove the rear power window regulator switch assembly with rear door upper armrest base panel.


Hide 69278C 5.REMOVE REAR DOOR INSIDE HANDLE BEZEL

a.
B564424

Using a moulding remover, disengage the 3 claws to remove the rear door inside handle bezel.


Hide 67604 6.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B564426C01
0.76,0.781 1.281,0.979 true 0.552,0.688 0.75,0.875 0.198,0.188 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disengage the claw as shown in the illustration.


b.
B564428

Remove the 3 screws.


c.
B564429C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 9 clips as shown in the illustration.


d.
B564430C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 4 claws and guide as shown in the illustration.


e.

w/ Illumination:

i.
B564432

Disengage the clamp.


ii.

Disconnect the connector.



f.
B564433C01
1.969,0.958 2.573,0.594 true 2.083,1.677 1.896,1.302 true 2.573,0.49 2.792,0.667 0.219,0.177 10 true *1 2,1.688 2.219,1.875 0.219,0.188 10 true *2
*1 Rear Door Inside Lock/Unlock Knob Locking Cable
*2 Rear Door Lock Open Lever Remote Control Cable
V113147

Remove in this Direction


Disconnect the rear door lock open lever remote control cable and rear door inside lock/unlock knob locking cable as shown in the illustration to remove the rear door trim board sub-assembly.


Hide 69206C 7.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B564435

Disengage the 3 claws to remove the rear door inside handle sub-assembly.


Hide 74222C 8.REMOVE REAR DOOR ARMREST COVER

a.
B564436C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claw to remove the rear door armrest cover as shown in the illustration.


Hide 65908D 9.REMOVE REAR CURTAIN SUB-ASSEMBLY (w/ Rear Door Sunshade)

a.
B564438

Remove the 7 screws.


b.

Disengage 3 guides to remove the rear curtain sub-assembly.


Hide 65923E 10.REMOVE CURTAIN HOOK (w/ Rear Door Sunshade)

HINT:

Use the same procedure for both curtain hooks.


a.
B564480C01
1.323,0.76 1.646,0.521 true 1.698,0.427 2.01,0.583 0.313,0.156 10 false *a
*a Protective Tape
V113146

Insert Screwdriver Here


Using a screwdriver with its tip wrapped with protective tape, push out the pin as shown in the illustration.


b.
B567550C01
1.25,1.115 0.854,0.49 true 0.635,0.375 0.948,0.531 0.313,0.156 10 false *a
*a Protective Tape
V113146

Insert Screwdriver Here


Using a screwdriver with its tip wrapped with protective tape, disengage the pin.


c.
B567551C01
0,0 0,0 false
V100135

Push
V113147

Remove in this Direction


Disengage the 2 claws to remove the curtain hook as shown in the illustration.


Hide 67674A 11.REMOVE REAR DOOR FRAME GARNISH

a.
B564439C01
0,0 0,0 false
V113147

Remove in this Direction


Using a clip remover, disengage the clip.


b.

Disengage the 2 guides to remove the rear door frame garnish as shown in the illustration.


Hide 67676C 12.REMOVE NO. 2 REAR DOOR FRAME GARNISH

a.
B564441

Disengage the 3 claws to remove the No. 2 rear door frame garnish.


Hide 86160B 13.REMOVE REAR SPEAKER ASSEMBLY

Hide 68640A 14.REMOVE REAR DOOR CHECK ASSEMBLY

a.
B564443C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt, 2 nuts and rear door check assembly.


Hide 67872 15.REMOVE REAR DOOR WEATHERSTRIP

a.
B564444C01
0,0 0,0 false
V100155

Double-sided Tape


Using a clip remover, disengage the 28 clips, guide and remove the rear door weatherstrip.


Hide 68174A 16.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

a.
B564445C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door inner glass weatherstrip as shown in the illustration.


Hide 67848A 17.REMOVE NO. 1 REAR DOOR VENT SEAL

a.
B564447C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 3 guides to remove the No. 1 rear door vent seal as shown in the illustration.


Hide 67225A 18.REMOVE QUARTER WINDOW UPPER STOP

a.
B564449C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the quarter window upper stop as shown in the illustration.


Hide 67842E 19.REMOVE REAR DOOR SERVICE HOLE COVER

a.
B564451

Disconnect the connector.


b.

Disengage the 2 clamps.


c.
B564452

Disengage the 7 clips and remove the rear door service hole cover.


Hide 68152C 20.REMOVE REAR DOOR GLASS RUN

a.
B567548

Remove the rear door glass run.


Hide 67408E 21.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

a.
B564453C01
0,0 0,0 false
V100135

Screw
V100136

Bolt


Remove the screw, 2 bolts and rear door window division bar sub-assembly.


Hide 68124B 22.REMOVE REAR DOOR QUARTER WINDOW GLASS

a.
B564454C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door quarter window glass as shown in the illustration.


Hide 68189 23.REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP

a.
B564456

Remove the rear door quarter window weatherstrip from the rear door quarter window glass.


Hide 68104 24.REMOVE REAR DOOR GLASS SUB-ASSEMBLY

a.
B564457

Remove the hole plug.


b.

Connect the rear power window regulator switch assembly.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON.


e.

Move the rear door glass sub-assembly so that the door glass bolts can be seen.


f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Disconnect the rear power window regulator switch assembly.


i.
B564458

Remove the 2 bolts.

NOTICE:

Do not damage the rear door glass sub-assembly.



j.
B564459C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door glass sub-assembly as shown in the illustration.

NOTICE:

Do not damage the rear door glass sub-assembly.



Hide 25.REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY

a.
B564461

Disconnect the connector.


b.

Remove the 6 nuts and rear door window regulator assembly.


Hide 69060A 26.REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY

Hide 69240 27.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B564463

Disengage the 2 claws and move the lever as shown in the illustration.


b.
B564465C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door outside handle assembly as shown in the illustration.


Hide 69227M 28.REMOVE REAR DOOR OUTSIDE HANDLE COVER

a.
B564467

Using a T30 "TORX" socket wrench, loosen the screw.

HINT:

The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.



b.

Disengage the 2 claws to remove the rear door outside handle cover.


Hide 69241G 29.REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD

a.
B564468

Disengage the 2 claws and guide to remove the rear door front outside handle pad.


Hide 69242G 30.REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD

a.
B564469

Disengage the claw and 3 guides to remove the rear door rear outside handle pad.


Hide 69204A 31.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.
B564470

Using a T30 "TORX" socket wrench, remove the screw.


b.
B564471C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claw and guide to remove the rear door outside handle frame sub-assembly as shown in the illustration.


Hide 67836H 32.REMOVE REAR DOOR LOCK CHILD PROTECTION COVER

a.
B564472

Disengage the 6 claws to remove the rear door lock child protection cover.


Hide 75740 33.REMOVE REAR DOOR BELT MOULDING ASSEMBLY

Hide 75762B 34.REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING

Hide 75766B 35.REMOVE REAR DOOR REAR WINDOW FRAME MOULDING

Hide 75764A 36.REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING

Hide 75792 37.REMOVE DOOR WINDOW FRAME MOULDING CLIP

a.
B564473C01
3.094,1.24 2.198,0.927 true 3.115,1.156 3.427,1.313 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the door window frame moulding clip.


Hide 67896 38.REMOVE REAR DOOR NO. 3 WEATHERSTRIP

a.

Remove the rear door No. 3 weatherstrip.

B564475C01
0,0 0,0 false
V100155

Double-sided Tape - -



Hide 67003C 39.REMOVE REAR DOOR PANEL CUSHION

a.
B564476

Disengage the claw to remove the rear door panel cushion.


Hide 75078 40.REMOVE REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY

Hide 41.REMOVE REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY

Hide 75797G 42.REMOVE REAR DOOR UPPER OUTSIDE MOULDING PAD

Hide 67888A 43.REMOVE REAR DOOR NO. 2 WEATHERSTRIP

a.
B564477

Disengage the 6 clips to remove the rear door No. 2 weatherstrip.


Hide 67846A 44.REMOVE REAR DOOR FRONT OUTSIDE SEAL

a.
B564478

Disengage the 4 claws and guide to remove the rear door front outside seal.


Hide 67837C 45.REMOVE REAR DOOR DUST PROOF SEAL

a.
B564479

Disengage the 3 claws to remove the 3 rear door dust proof seals.