Home › Vehicle Exterior › WINDOW / GLASS › QUARTER WINDOW GLASS
RM37A0E _59 Vehicle Exterior _086899 WINDOW / GLASS _0416699 QUARTER WINDOW GLASS A

WINDOW / GLASS  QUARTER WINDOW GLASS  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR NO. 2 SEAT ASSEMBLY

Hide 58387B 2.REMOVE REAR FLOOR FINISH PLATE

Hide 72138M 3.REMOVE REAR OUTER SEAT TRACK BRACKET COVER

Hide 67918A 4.REMOVE REAR DOOR SCUFF PLATE

Hide 62332C 5.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

Hide 64713F 6.REMOVE FRONT DECK SIDE TRIM COVER LH (for LH Side)

Hide 64712F 7.REMOVE FRONT DECK SIDE TRIM COVER RH (for RH Side)

Hide 73370E 8.DISCONNECT REAR SEAT OUTER BELT ASSEMBLY

Hide 64715E 9.REMOVE NO. 2 DECK SIDE TRIM COVER

Hide 73570 10.DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY

Hide 64974 11.REMOVE DECK TRIM POCKET COVER

Hide 64725F 12.REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

Hide 64740C 14.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)

Hide 88625T 15.REMOVE COOLER (NO. 2 ROOM TEMP. SENSOR) THERMISTOR (for RH Side)

Hide 64730B 16.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)

Hide 62639A 17.REMOVE QUARTER PILLAR GARNISH

Hide 62480A 18.REMOVE INNER ROOF SIDE GARNISH ASSEMBLY

Hide 62720A 19.REMOVE QUARTER WINDOW ASSEMBLY

a.
B565190C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the area around the installation position of the quarter window assembly on the vehicle body to prevent it from being scratched.


b.
B565191C01
1.552,0.375 2.188,0.375 2.188,0.375 1.969,0.656 true 1.021,0.688 0.448,0.885 0.448,0.885 1.073,1.344 true 2.542,1.781 2.542,1.531 true 0.396,1.771 0.667,1.604 true 2.24,0.271 2.552,0.427 0.313,0.156 10 true *a 0.229,0.813 0.542,0.969 0.313,0.156 10 false *b 2.458,1.823 2.771,1.979 0.313,0.156 10 false *b 0.208,1.719 0.521,1.875 0.313,0.156 10 true *a
*a Piano Wire
*b Clip


Pass a piano wire between the vehicle body and quarter window assembly from the interior.


c.

Tie both wire ends to wooden blocks or similar objects that can serve as handles.


d.

Cut the adhesive by pulling the piano wire around the quarter window assembly.

NOTICE:

When separating the quarter window assembly, be careful not to damage the paint or interior and exterior ornaments.



e.
B565192

Using suction cups, disengage the 3 clips and remove the quarter window assembly.

NOTICE:

Be careful not to drop the quarter window assembly.



Hide 20.CLEAN VEHICLE BODY

a.

Clean and shape the contact surfaces of the vehicle body.

i.
B423490C01
0.76,0.479 1.271,0.458 false 0.573,0.396 0.885,0.552 0.313,0.156 10 false *a 1.646,1.854 1.802,2.052 0.156,0.198 10 false a
*a Vehicle Body
V100155

Adhesive


Using a knife, cut off any excess adhesive on the contact surfaces of the vehicle body as shown in the illustration.

Standard Dimension:
Area Dimension
a 1.0 mm (0.0394 in.) or more


NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave approximately 1.0 mm (0.0394 in.) of adhesive on the vehicle body.




b.

Clean the contact surfaces of the vehicle body with a piece of cloth saturated with non-residue solvent.

HINT:

Even if all of the adhesive has been removed, clean the vehicle body.