Home › Vehicle Exterior › WINDOW / GLASS › QUARTER WINDOW GLASS
RM37A0E _59 Vehicle Exterior _086899 WINDOW / GLASS _0416699 QUARTER WINDOW GLASS A

WINDOW / GLASS  QUARTER WINDOW GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 62720A 1.INSTALL QUARTER WINDOW ASSEMBLY

a.

Using a brush or sponge, coat the adhesive application area of a new quarter window assembly with glass primer.

B565193C01
1.792,0.635 1.948,0.833 0.156,0.198 10 false A 1.885,1 2.042,1.198 0.156,0.198 10 true A 3.198,0.313 3.385,0.531 0.188,0.219 10 true B 3.198,0.656 3.385,0.875 0.188,0.219 10 true B 3.917,0.99 4.104,1.208 0.188,0.219 10 true C 4.365,1.094 4.552,1.313 0.188,0.219 10 true C 3.104,1.75 3.292,1.969 0.188,0.219 10 true D 3.083,2.125 3.271,2.344 0.188,0.219 10 true D 5.292,0.198 5.646,0.469 0.354,0.271 10 false A-A 0.375,2.427 0.729,2.698 0.354,0.271 10 false B-B 2.719,2.438 3.073,2.708 0.354,0.271 10 false C-C 5.167,2.281 5.521,2.552 0.354,0.271 10 false D-D 6.229,1.406 6.385,1.604 0.156,0.198 10 false a 1.208,3.427 1.365,3.625 0.156,0.198 10 false b 3.594,3.417 3.75,3.615 0.156,0.198 10 false c 6.052,3.365 6.208,3.563 0.156,0.198 10 false d 0.354,0.25 0.729,0.49 0.375,0.24 12 false *A
*A Back Side - -
V100155

Glass Primer - -


Standard Dimension:
Area Dimension Area Dimension
a 17.3 mm (0.681 in.) or more b 17.7 mm (0.697 in.) or more
c 20.0 mm (0.787 in.) or more d 13.7 mm (0.539 in.) or more


NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.

Apply adhesive to the quarter window assembly.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.
B214800C28
1.198,0.438 1.385,0.5 false 0.5,0.625 0.656,0.823 0.156,0.198 10 false a 1.344,1.365 1.5,1.563 0.156,0.198 10 false a 1.115,0.885 1.271,1.083 0.156,0.198 10 false b 0.76,1 0.917,1.198 0.156,0.198 10 false b 1.406,0.438 1.646,0.615 0.24,0.177 10 false *a
*a Nozzle


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 8.0 to 11.0 mm (0.315 to 0.433 in.)
b 6.0 to 9.0 mm (0.236 to 0.354 in.)



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the quarter window assembly as shown in the illustration.

B565194C01
4.135,0.323 4.292,0.521 0.156,0.198 10 false A 4.094,0.656 4.25,0.854 0.156,0.198 10 true A 4.865,1 5.063,1.198 0.198,0.198 10 true B 5.24,1.115 5.438,1.313 0.198,0.198 10 true B 3.969,1.781 4.167,1.979 0.198,0.198 10 true C 3.969,2.094 4.167,2.292 0.198,0.198 10 true C 0.469,2.219 0.875,2.5 0.406,0.281 10 false A-A 2.771,2.229 3.177,2.51 0.406,0.281 10 false B-B 5.188,2.188 5.594,2.469 0.406,0.281 10 false C-C 1.802,0.26 2.177,0.5 0.375,0.24 12 false *A 1.031,3.583 1.188,3.781 0.156,0.198 10 false a 1.333,3.594 1.49,3.792 0.156,0.198 10 false b 3.49,3.573 3.646,3.771 0.156,0.198 10 false c 3.802,3.51 3.958,3.708 0.156,0.198 10 false d 3.646,2.313 3.802,2.51 0.156,0.198 10 false e 5.979,3.51 6.135,3.708 0.156,0.198 10 false f 6.167,3.573 6.323,3.771 0.156,0.198 10 false g
*A Back Side - -
V100155

Adhesive - -


Standard Dimension:
Area Dimension Area Dimension
a 6.3 mm (0.248 in.) b 11.4 mm (0.449 in.)
c 14.4 mm (0.567 in.) d 5.6 mm (0.220 in.)
e 6.0 mm (0.236 in.) f 6.3 mm (0.248 in.)
g 7.4 mm (0.291 in.) - -




c.

Install the quarter window assembly to the vehicle body.

i.

Using suction cups, engage the 3 clips to install the quarter window assembly.

NOTICE:
·

Check that the clips are engaged to the vehicle body correctly.

·

Check the clearance between the vehicle body and quarter window assembly.




ii.

Lightly press the outer surface of the quarter window assembly to ensure that the quarter window assembly is securely fit to the vehicle body.

HINT:

Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.



iii.

Using a scraper, remove any excess or protruding adhesive.


iv.

Hold the quarter window assembly using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.




Hide 2.INSPECT FOR LEAK

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 62480A 3.INSTALL INNER ROOF SIDE GARNISH ASSEMBLY

Hide 62639A 4.INSTALL QUARTER PILLAR GARNISH

Hide 64730B 5.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)

Hide 88625T 6.INSTALL COOLER (NO. 2 ROOM TEMP. SENSOR) THERMISTOR (for RH Side)

Hide 64740C 7.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)

Hide 64725F 9.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

Hide 64974 10.INSTALL DECK TRIM POCKET COVER

Hide 73570 11.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY

Hide 64715E 12.INSTALL NO. 2 DECK SIDE TRIM COVER

Hide 73370E 13.CONNECT REAR SEAT OUTER BELT ASSEMBLY

Hide 64712F 14.INSTALL FRONT DECK SIDE TRIM COVER RH (for RH Side)

Hide 64713F 15.INSTALL FRONT DECK SIDE TRIM COVER LH (for LH Side)

Hide 62332C 16.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

Hide 67918A 17.INSTALL REAR DOOR SCUFF PLATE

Hide 72138M 18.INSTALL REAR OUTER SEAT TRACK BRACKET COVER

Hide 58387B 19.INSTALL REAR FLOOR FINISH PLATE

Hide 20.INSTALL REAR NO. 2 SEAT ASSEMBLY