This DTC is stored when the combination meter assembly detects a short in a turn signal light circuit.
If there is a short in a turn signal light circuit, all of the turn signal lights in that circuit will not blink.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B150819 | Turn Signal/Hazard Flasher Circuit Current Above Threshold | Diagnosis Condition:
Auxiliary battery voltage is 10 V or more Malfunction Status: Short in turn signal light circuit |
·
Headlight assembly -
Front turn signal light socket -
Front turn signal light bulb ·
Outer mirror control ECU assembly*1 ·
Outer rear view mirror assembly -
Side turn signal light assembly ·
Device connected to option connector (trailer towing)*2 ·
Rear combination light assembly -
Rear combination light cord -
Rear turn signal light socket -
Rear turn signal light bulb ·
Harness or connector ·
Combination meter assembly |
*1: w/ Seat Position Memory
*2: w/ Option Connector (Trailer Towing)
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Inspect the turn signal light bulbs before performing the following procedure.
Check the problem symptoms.
| Result | Proceed to |
|---|---|
| All LH side turn signal lights do not blink | A |
| All RH side turn signal lights do not blink | B |
A
B
Disconnect the A64 and A66 headlight assembly LH connector.
Operate the turn signal switch and check that the LH side turn signal lights other than the front turn signal light blink.
If the LH side turn signal lights other than the front turn signal light blink, a component of the headlight assembly LH is malfunctioning.
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the front turn signal light blink | A |
| Problem symptoms do not change
(All LH side turn signal lights do not blink) |
B |
A
B
Connect the A66 headlight assembly LH connector.
Operate the turn signal switch and check that the LH side turn signal lights other than the front turn signal light blink.
If all LH side turn signal lights do not blink, the front turn signal light socket LH is malfunctioning.
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the front turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
B
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Seat Position Memory | A |
| w/o Seat Position Memory | B |
A
B
Connect the headlight assembly LH connectors.
Disconnect the J23 outer mirror control ECU assembly LH connector.
Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.
If the LH side turn signal lights other than the side turn signal light blink, there is a malfunction in the circuit after the J23 connector.
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the side turn signal light blink | A |
| Problem symptoms do not change
(All LH side turn signal lights do not blink) |
B |
A
B
Connect the J23 outer mirror control ECU assembly LH connector.
Disconnect the z17 outer mirror control ECU assembly LH connector.
Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.
If all LH side turn signal lights do not blink, the outer mirror control ECU assembly LH is malfunctioning.
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the side turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
B
Remove the side turn signal light assembly LH from the outer rear view mirror assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL
Connect the z17 outer mirror control ECU assembly LH connector.
Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.
If all LH side turn signal lights do not blink, the outer rear view mirror assembly LH is malfunctioning.
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the side turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
B
Connect the headlight assembly LH connectors.
Disconnect the J31 outer rear view mirror assembly LH connector.
Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.
If the LH side turn signal lights other than the side turn signal light blink, a component of the outer rear view mirror assembly LH is malfunctioning.
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the side turn signal light blink | A |
| Problem symptoms do not change
(All LH side turn signal lights do not blink) |
B |
A
B
Remove the side turn signal light assembly LH from the outer rear view mirror assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL
Connect the J31 outer rear view mirror assembly LH connector.
Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.
If all LH side turn signal lights do not blink, the outer rear view mirror assembly LH is malfunctioning.
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the side turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
B
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Option Connector (Trailer Towing) | A |
| w/o Option Connector (Trailer Towing) | B |
A
B
Connect the outer rear mirror control ECU assembly LH connector.*1
Connect the outer rear view mirror assembly LH connector.*2
Disconnect the M75 option connector (trailer towing).
Operate the turn signal switch and check that the LH side turn signal lights blink.
If all LH side turn signal lights blink, the device connected to the option connector (trailer towing) is malfunctioning.
*1: w/ Seat Position Memory
*2: w/o Seat Position Memory
| Result | Proceed to |
|---|---|
| All LH side turn signal lights blink | A |
| Problem symptoms do not change
(All LH side turn signal lights do not blink) |
B |
A
B
Connect the option connector (trailer towing).
Disconnect the M59 rear combination light assembly LH connector.
Operate the turn signal switch and check that the LH side turn signal lights other than the rear turn signal light blink.
If the LH side turn signal lights other than the rear turn signal light blink, a component of the rear combination light assembly LH is malfunctioning.
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the rear turn signal light blink | A |
| Problem symptoms do not change
(All LH side turn signal lights do not blink) |
B |
A
B
Connect the outer rear mirror control ECU assembly LH connector.*1
Connect the outer rear view mirror assembly LH connector.*2
Disconnect the M59 rear combination light assembly LH connector.
Operate the turn signal switch and check that the LH side turn signal lights other than the rear turn signal light blink.
If the LH side turn signal lights other than the rear turn signal light blink, a component of the rear combination light assembly LH is malfunctioning.
*1: w/ Seat Position Memory
*2: w/o Seat Position Memory
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the rear turn signal light blink | A |
| Problem symptoms do not change
(All LH side turn signal lights do not blink) |
B |
A
B
Remove the rear turn signal light socket LH from the rear combination light assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY
Connect the M59 rear combination light assembly LH connector.
Operate the turn signal switch and check that the LH side turn signal lights other than the rear turn signal light blink.
If all LH side turn signal lights do not blink, the rear combination light cord LH is malfunctioning.
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the rear turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
B
Disconnect the A64 and A66 headlight assembly LH connector.
Disconnect the J23 outer mirror control ECU assembly LH connector.*1
Disconnect the J31 outer rear view mirror assembly LH connector.*2
Disconnect the M75 option connector (trailer towing).*3
Disconnect the H22 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A64-1 (B), A66-5 (B), J23-11 (TRNI)*1, J31-4 (B)*2, M75-4 (TRNL)*3 or H22-11 (LL) - Body ground | Always | 10 kΩ or higher |
| M59-1 (TRN) or H22-10 (TRNL) - Body ground | Always | 10 kΩ or higher |
*1: w/ Seat Position Memory
*2: w/o Seat Position Memory
*3: w/ Option Connector (Trailer Towing)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A63 and A65 headlight assembly RH connector.
Operate the turn signal switch and check that the RH side turn signal lights other than the front turn signal light blink.
If the RH side turn signal lights other than the front turn signal light blink, a component of the headlight assembly RH is malfunctioning.
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the front turn signal light blink | A |
| Problem symptoms do not change
(All RH side turn signal lights do not blink) |
B |
A
B
Connect the A65 headlight assembly RH connector.
Operate the turn signal switch and check that the RH side turn signal lights other than the front turn signal light blink.
If all RH side turn signal lights do not blink, the front turn signal light socket RH is malfunctioning.
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the front turn signal light blink | A |
| All RH side turn signal lights do not blink | B |
A
B
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Seat Position Memory | A |
| w/o Seat Position Memory | B |
A
B
Connect the headlight assembly RH connectors.
Disconnect the J7 outer mirror control ECU assembly RH connector.
Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.
If the RH side turn signal lights other than the side turn signal light blink, there is a malfunction in the circuit after the J7 connector.
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the side turn signal light blink | A |
| Problem symptoms do not change
(All RH side turn signal lights do not blink) |
B |
A
B
Connect the J7 outer mirror control ECU assembly RH connector.
Disconnect the z16 outer mirror control ECU assembly RH connector.
Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.
If all RH side turn signal lights do not blink, the outer mirror control ECU assembly RH is malfunctioning.
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the side turn signal light blink | A |
| All RH side turn signal lights do not blink | B |
A
B
Remove the side turn signal light assembly RH from the outer rear view mirror assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL
Connect the z16 outer mirror control ECU assembly RH connector.
Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.
If all RH side turn signal lights do not blink, the outer rear view mirror assembly RH is malfunctioning.
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the side turn signal light blink | A |
| All RH side turn signal lights do not blink | B |
A
B
Connect the headlight assembly RH connectors.
Disconnect the J15 outer rear view mirror assembly RH connector.
Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.
If the RH side turn signal lights other than the side turn signal light blink, a component of the outer rear view mirror assembly RH is malfunctioning.
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the side turn signal light blink | A |
| Problem symptoms do not change
(All RH side turn signal lights do not blink) |
B |
A
B
Remove the side turn signal light assembly RH from the outer rear view mirror assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL
Connect the J15 outer rear view mirror assembly RH connector.
Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.
If all RH side turn signal lights do not blink, the outer rear view mirror assembly RH is malfunctioning.
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the side turn signal light blink | A |
| All RH side turn signal lights do not blink | B |
A
B
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Option Connector (Trailer Towing) | A |
| w/o Option Connector (Trailer Towing) | B |
A
B
Connect the outer mirror control ECU assembly RH connector.*1
Connect the outer rear view mirror assembly RH connector.*2
Disconnect the M75 option connector (trailer towing).
Operate the turn signal switch and check that the RH side turn signal lights blink.
If all RH side turn signal lights blink, the device connected to the option connector (trailer towing) is malfunctioning.
*1: w/ Seat Position Memory
*2: w/o Seat Position Memory
| Result | Proceed to |
|---|---|
| All RH side turn signal lights blink | A |
| Problem symptoms do not change
(All RH side turn signal lights do not blink) |
B |
A
B
Connect the option connector (trailer towing).
Disconnect the M8 rear combination light assembly RH connector.
Operate the turn signal switch and check that the RH side turn signal lights other than the rear turn signal light blink.
If the RH side turn signal lights other than the rear turn signal light blink, a component of the rear combination light assembly RH is malfunctioning.
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the rear turn signal light blink | A |
| Problem symptoms do not change
(All RH side turn signal lights do not blink) |
B |
A
B
Connect the outer mirror control ECU assembly RH connector.*1
Connect the outer rear view mirror assembly RH connector.*2
Disconnect the M8 rear combination light assembly RH connector.
Operate the turn signal switch and check that the RH side turn signal lights other than the rear turn signal light blink.
If the RH side turn signal lights other than the rear turn signal light blink, a component of the rear combination light assembly RH is malfunctioning.
*1: w/ Seat Position Memory
*2: w/o Seat Position Memory
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the rear turn signal light blink | A |
| Problem symptoms do not change
(All RH side turn signal lights do not blink) |
B |
A
B
Remove the rear turn signal light socket RH from the rear combination light assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY
Connect the M8 rear combination light assembly RH connector.
Operate the turn signal switch and check that the RH side turn signal lights other than the rear turn signal light blink.
If all RH side turn signal lights do not blink, the rear combination light cord RH is malfunctioning.
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the rear turn signal light blink | A |
| All RH side turn signal lights do not blink | B |
A
B
Disconnect the A63 and A65 headlight assembly RH connector.
Disconnect the J7 outer mirror control ECU assembly RH connector.*1
Disconnect the J15 outer rear view mirror assembly RH connector.*2
Disconnect the M75 option connector (trailer towing).*3
Disconnect the H22 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A63-1 (B), A65-5 (B), J7-11 (TRNI)*1, J15-4 (B)*2, M75-5 (TRNR)*3 or H22-7 (LR) - Body ground | Always | 10 kΩ or higher |
| M8-1 (TRN) or H22-13 (TRNR) - Body ground | Always | 10 kΩ or higher |
*1: w/ Seat Position Memory
*2: w/o Seat Position Memory
*3: w/ Option Connector (Trailer Towing)
| Proceed to |
|---|
| OK |
| NG |
OK
NG