Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM37A0E _57 Power Source / Network _086883 NETWORKING _0417284 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Communication stop for "ECM (Engine)" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

ECM main line or connector

·

Power source circuit of ECM

·

ECM ground circuit

·

ECM



WIRING DIAGRAM

C380553E35
0.198,1.771 0.656,1.969 0.458,0.198 10 false H97 0.531,1.771 3.208,2.073 2.677,0.302 10 false No. 11 Global CAN Junction Connector 1.677,1.365 2.135,1.563 0.458,0.198 10 false 20 1.677,0.781 2.135,0.979 0.458,0.198 10 false 9 5.26,0.667 5.719,0.865 0.458,0.198 10 false 13 5.656,0.781 6.115,0.979 0.458,0.198 10 false CANH 5.271,1.26 5.729,1.458 0.458,0.198 10 false 26 5.677,1.646 6.135,1.844 0.458,0.198 10 false CANL 5.313,2.177 5.771,2.375 0.458,0.198 10 false 4 5.219,2.406 5.677,2.604 0.458,0.198 10 false A28 5.646,2.417 6.146,2.635 0.5,0.219 10 false IGSW 5.302,2.854 5.76,3.052 0.458,0.198 10 false 2 5.646,3.104 6.104,3.302 0.458,0.198 10 false +B 5.302,3.583 5.76,3.781 0.458,0.198 10 false 3 5.677,3.813 6.135,4.01 0.458,0.198 10 false +B2 5.26,4.229 5.719,4.427 0.458,0.198 10 false 46 5.656,4.479 6.156,4.688 0.5,0.208 10 false MREL 5.667,5.229 6.125,5.427 0.458,0.198 10 false E1 5.229,5.219 5.688,5.417 0.458,0.198 10 false C54 5.271,4.99 5.729,5.188 0.458,0.198 10 false 53 5.854,5.938 6.313,6.135 0.458,0.198 10 false ECM 1.49,4.438 3.385,4.792 1.896,0.354 10 false to EFI-MAIN Relay 1.333,2.396 2.958,2.802 1.625,0.406 10 false from IG2 NO. 1 Relay 3.656,2.24 4.833,2.49 1.177,0.25 10 false ECU-IG2 NO. 1 5.219,1.51 5.677,1.708 0.458,0.198 10 false A28 5.229,0.917 5.688,1.115 0.458,0.198 10 false A28 5.219,3.083 5.677,3.281 0.458,0.198 10 false A28 5.229,3.802 5.688,4 0.458,0.198 10 false A28 5.229,4.469 5.688,4.667 0.458,0.198 10 false A28 1.365,3.063 3.26,3.417 1.896,0.354 10 false from EFI-MAIN Relay

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A28 ECM connector.


c.
C380552C29
1.563,0.135 1.948,0.385 0.385,0.25 2.865,1.552 2.865,0.635 2.865,0.635 2.698,0.635 true 2.865,1.708 2.865,2.927 2.865,2.927 2.698,2.927 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.635,0.177 1.948,0.375 0.313,0.198 10 false A28 2.229,0.563 2.729,0.854 0.5,0.292 10 false CANH 2.26,2.854 2.76,3.146 0.5,0.292 10 false CANL
*a Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-13 (CANH) - A28-26 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

2.CHECK ECM POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM)

2.CHECK ECM POWER SOURCE CIRCUIT

Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)