Home › Suspension › REAR SUSPENSION › REAR LOWER ARM
RM37A0E _53 Suspension _086866 REAR SUSPENSION _0417441 REAR LOWER ARM A

REAR SUSPENSION  REAR LOWER ARM  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear suspension arm assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: for RH Side

Rear wheel alignment adjustment
for HV Model

Perform "Calibration".


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for Gasoline Model
1.

Perform "Reset Memory".

2.

Perform "Calibration".


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Gas leak from exhaust system is repaired*1 Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


for A25A-FXS, A25B-FXS:(Click here)
for 2GR-FKS:(Click here)

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 17430 2.REMOVE TAIL EXHAUST PIPE ASSEMBLY (for RH Side)

Hide 48738 3.REMOVE REAR SUSPENSION ARM COVER

a.
C426704

Remove the 2 bolts.


b.

Disengage the 2 guides to remove the rear suspension arm cover from the rear No. 2 suspension arm assembly.


Hide 4.SEPARATE REAR STABILIZER LINK ASSEMBLY

Hide 48231B 5.REMOVE REAR COIL SPRING

Hide 48258C 6.REMOVE REAR LOWER COIL SPRING INSULATOR

Hide 48740F 7.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.
C426705

Remove the nut, rear No. 2 suspension camber adjust cam, rear suspension toe adjust cam sub-assembly and rear No. 2 suspension arm assembly.

NOTICE:

Hold the rear suspension toe adjust cam sub-assembly while rotating the nut.



Hide 48720A 8.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY

a.

for Gasoline Model:

i.
C426707C01
1.781,1.615 2.208,1.615 false 1.927,1.813 2.354,1.813 false 2.26,1.542 2.573,1.698 0.313,0.156 10 false *a 2.396,1.729 2.708,1.885 0.313,0.156 10 false *b
*a Wooden Block
*b Transmission Jack


Using a transmission jack and a wooden block, support the rear differential carrier assembly.



b.

for HV Model:

i.
C426708C01
1.99,1.26 2.573,1.26 true 2.542,1.656 2.813,1.656 true 2.604,1.188 2.833,1.344 0.229,0.156 10 true *a 2.854,1.573 3.073,1.75 0.219,0.177 10 true *b
*a Wooden Block
*b Transmission Jack


Using a transmission jack and wooden block, support the rear suspension member sub-assembly.



c.
C426749

Remove the nut and separate the No. 2 parking brake wire assembly from the rear lower suspension member stopper.


d.
C426709

Remove the bolt, nut and rear lower suspension member stopper.


e.
C426710C01
1.719,1.688 1.958,1.688 false 1.021,1.979 1.26,1.979 false 1.552,1.583 1.865,1.74 0.313,0.156 10 false *a 0.844,1.906 1.156,2.063 0.313,0.156 10 false *b 2.333,0.125 2.521,0.323 0.188,0.198 10 true A 0.708,0.031 0.875,0.208 0.167,0.177 10 true B
*a Wooden Block
*b Transmission Jack


Using a transmission jack and a wooden block, support the rear axle carrier sub-assembly.


f.

Remove the nut (A) and spacer.


g.

Remove the bolt (B), nut and rear No. 1 suspension arm assembly from the rear axle carrier sub-assembly and rear suspension member sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



h.
C426709

Temporarily install the rear lower suspension member stopper with the bolt and nut.