Home › Vehicle Interior › SEAT BELT › OCCUPANT DETECTION SENSOR (for Front Side) › 2020.02–2020.11
RM37A0E _58 Vehicle Interior _086895 SEAT BELT _0417493 OCCUPANT DETECTION SENSOR A

SEAT BELT  OCCUPANT DETECTION SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during occupant detection sensor (separate type front seat cushion pad) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

CAUTION:
·
B401522

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·
B543257

Wear protective gloves. Sharp areas on the parts may injure your hands.



NOTICE:
·

If the front seat airbag assembly has been deployed, replace the front seat airbag assembly, separate type front seatback spring assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.

·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.



PROCEDURE

Hide 1.REMOVE FRONT SEAT ASSEMBLY

for Manual Seat:

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL

for Power Seat:

HINT:

Use the same procedure as for the driver seat.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL


Hide 73240 2.REMOVE FRONT SEAT INNER BELT ASSEMBLY LH

Hide 71073S 3.DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER

for Manual Seat:

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY

for Power Seat:

HINT:

Use the same procedure as for the driver seat.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


Hide 71868N 4.REMOVE FRONT SEAT FRONT CUSHION SHIELD (for Power Seat)

HINT:

Use the same procedure as for the driver seat.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


Hide 72551B 5.REMOVE RECLINING HINGE COVER (for Manual Seat)

Hide 72525A 6.REMOVE RECLINING ADJUSTER RELEASE HANDLE (for Manual Seat)

Hide 71811D 7.REMOVE FRONT SEAT CUSHION SHIELD

Hide 71861 8.REMOVE FRONT SEAT INNER CUSHION SHIELD

Hide 9.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY

for Manual Seat:

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY

for Power Seat:

HINT:

Use the same procedure as for the driver seat.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


Hide 10.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

for Manual Seat:

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY

for Power Seat:

HINT:

Use the same procedure as for the driver seat.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


Hide 71511S 11.REMOVE OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD)

a.

Using a screwdriver, disengage the 14 claws and remove the occupant detection sensor (separate type front seat cushion pad) from the separate type front seat cushion cover as shown in the illustration.

B471092C02
1.542,2.573 1.938,2.573 false 1.948,2.438 2.188,2.656 0.24,0.219 10 false *a
*a Screwdriver - -