Home › Engine / Hybrid System › 2GR-FKS (FUEL) › FUEL PUMP (for High Pressure) › 2020.02–2020.11
RM37A0E _51 Engine / Hybrid System _086852 2GR-FKS FUEL _0417513 FUEL PUMP(for High Pressure) A

2GR-FKS FUEL  FUEL PUMP(for High Pressure)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Replacement of fuel pump assembly

·

Replacement of port fuel injector assembly

·

Replacement of fuel pressure sensor (fuel delivery pipe with sensor assembly)

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Replacement of air fuel ratio sensor

·

Replacement of heated oxygen sensor

·

Gas leak from exhaust system is repaired


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A357489

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.



NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 17140 5.REMOVE EXHAUST MANIFOLD ASSEMBLY RH (TWC: Front Catalyst)

Hide 23214A 6.REMOVE FUEL PUMP PROTECTOR

a.
A454403

Disengage the clamp to disconnect the fuel tube sub-assembly from the fuel pump protector.


b.
A454404

Remove the 2 bolts and fuel pump protector from the cylinder head sub-assembly.


Hide 7.DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

a.
A393305

Disengage the clamp and disconnect the No. 2 fuel tube sub-assembly from the fuel pump assembly.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23881B 8.REMOVE FUEL HOSE BRACKET

a.
A393306

Remove the bolt and fuel hose bracket from the cylinder head cover sub-assembly.


Hide 23801P 9.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

CAUTION:

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.


a.
A454405

Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.


b.
A454406

Loosen the 2 bolts of the fuel pump assembly.


c.

Remove the No. 1 fuel pipe sub-assembly from the fuel delivery pipe RH and fuel pump assembly.


Hide 23100X 10.REMOVE FUEL(ENGINE ROOM SIDE) PUMP ASSEMBLY

a.
A454407

Disconnect the fuel pump assembly connector.


b.
A454408

Remove the 2 bolts, fuel pump assembly and fuel pump lifter guide from the cylinder head cover sub-assembly.


c.
A400606

Remove the O-ring from the fuel pump assembly.


d.
A368941

Remove the fuel pump lifter assembly from the fuel pump lifter housing.


e.
A368942

Remove the fuel pump spacer gasket from the cylinder head cover sub-assembly.