Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM
RM37A0E _53 Suspension _086867 TIRE PRESSURE MONITORING _0417517 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2198  Initialization Switch Error (for Test Diagnosis)  


DESCRIPTION

The switch circuit inside the combination meter assembly turns on and off according to the steering pad switch assembly operation.

During test mode, the tire pressure warning light blinks at 0.125 second intervals when "Set Pressure" is selected on the multi-information display, and illuminates when the "OK" switch (steering pad switch assembly) is pressed.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C2198 Initialization Switch Error (for Test Diagnosis) Test mode procedure is performed.
·

Steering pad switch assembly

·

Spiral cable sub-assembly

·

Wire harness or connector

·

Tire pressure warning ECU and receiver


-

WIRING DIAGRAM

C427673E01
4.479,1.448 7.104,1.677 2.625,0.229 10 false Tire Pressure Warning ECU and Receiver 4.479,1.281 4.885,1.51 0.406,0.229 10 false M51 3.458,2.958 3.865,3.188 0.406,0.229 10 false H24 3.458,3.354 3.865,3.583 0.406,0.229 10 false H24 3.458,3.75 3.865,3.979 0.406,0.229 10 false H24 4.917,2.938 5.323,3.167 0.406,0.229 10 false z1 4.917,3.344 5.323,3.573 0.406,0.229 10 false z1 4.917,3.74 5.323,3.969 0.406,0.229 10 false z1 1.51,2.448 3.385,2.698 1.875,0.25 10 false Combination Meter Assembly 3.146,4.083 5.073,4.333 1.927,0.25 10 false Spiral Cable Sub-assembly 5.052,4.083 7.156,4.354 2.104,0.271 10 false Steering Pad Switch Assembly 3.5,2.76 3.906,2.99 0.406,0.229 10 false 10 3.51,3.156 3.917,3.385 0.406,0.229 10 false 11 3.542,3.552 3.948,3.781 0.406,0.229 10 false 4 4.906,3.552 5.313,3.781 0.406,0.229 10 false 10 4.938,3.156 5.344,3.385 0.406,0.229 10 false 4 4.938,2.76 5.344,2.99 0.406,0.229 10 false 5 4.646,0.458 5.052,0.688 0.406,0.229 10 false 3 1.469,0.875 1.875,1.104 0.406,0.229 10 false 21 1.458,1.438 1.865,1.667 0.406,0.229 10 false 29 1.448,1.854 1.854,2.083 0.406,0.229 10 false 28 1.74,0.99 2.146,1.219 0.406,0.229 10 false ES 1.74,1.542 2.26,1.802 0.521,0.26 10 false MSTI 1.729,1.969 2.25,2.229 0.521,0.26 10 false MSM+ 2.802,0.604 3.323,0.865 0.521,0.26 10 false INT 4.854,0.594 5.375,0.854 0.521,0.26 10 false CLSW 1.76,0.458 2.698,0.833 0.938,0.375 10 false - Tire Pressure Warning Light 3.156,0.458 3.563,0.688 0.406,0.229 10 false 4 3.833,2.854 4.354,3.115 0.521,0.26 10 false +DP2 3.833,3.25 4.354,3.51 0.521,0.26 10 false +DP 3.844,3.646 4.365,3.906 0.521,0.26 10 false EAU 2.135,4.708 3.031,5.042 0.896,0.333 10 false to Ground 1.51,2.292 1.917,2.521 0.406,0.229 10 false H21

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs and number of the transmitters (4 or 5) stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the H24 spiral cable sub-assembly connector.


b.

Disconnect the H21 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H24-10 (+DP2) - H21-28 (MSM+) Always Below 1 Ω
H24-10 (+DP2) or H21-28 (MSM+) - Body ground Always 10 kΩ or higher
H24-11 (+DP) - H21-29 (MSTI) Always Below 1 Ω
H24-11 (+DP) or H21-29 (MSTI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the M51 tire pressure warning ECU and receiver connector.


b.

Disconnect the H21 combination meter assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M51-3 (CLSW) - H21-4 (INT) Always Below 1 Ω
M51-3 (CLSW) or H21-4 (INT) - Body ground Always 10 kΩ or higher
H21-21 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK TERMINAL VOLTAGE (INT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (INT)
a.

Connect the M51 tire pressure warning ECU and receiver connector.


b.

Disconnect the H21 combination meter assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H21-4 (INT) - Body ground Ignition switch ON 8 to 15 V


Result:
Proceed to
OK
NG




OK

NG

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER