Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER › 2020.02–2020.11
RM37A0E _59 Vehicle Exterior _086903 EXTERIOR PANELS / TRIM _0417656 FRONT BUMPER A

EXTERIOR PANELS / TRIM  FRONT BUMPER  REASSEMBLY  


PROCEDURE

Hide 52146C 1.INSTALL FRONT BUMPER SIDE STAY LH

HINT:

Perform this procedure only when replacement of the front bumper side stay LH is necessary.


a.
B564119

Engage the claw.


b.

Engage the 2 clips as shown in the illustration.


c.
B564117

Install the front bumper side stay LH with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 52145H 2.INSTALL FRONT BUMPER SIDE STAY RH

HINT:

Use the same procedure as for the LH side.


Hide 52132A 3.INSTALL NO. 2 FRONT BUMPER REINFORCEMENT

HINT:

Perform this procedure only when replacement of the No. 2 front bumper reinforcement is necessary.


a.
B564116

Install the No. 2 front bumper reinforcement with the 4 nuts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 52021 4.INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY

HINT:

Perform this procedure only when replacement of the front bumper reinforcement sub-assembly is necessary.


a.
B570453

Install the front bumper reinforcement sub-assembly with the 8 bolts.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


b.
B564114

Engage the 2 clamps.


Hide 52618 5.INSTALL FRONT BUMPER LOWER ABSORBER

HINT:

Perform this procedure only when replacement of the front bumper lower absorber is necessary.


a.
B564113

Engage the 2 guides to install the front bumper lower absorber.


Hide 52611 6.INSTALL FRONT BUMPER ENERGY ABSORBER

HINT:

Perform this procedure only when replacement of the front bumper energy absorber is necessary.


a.
B564112

Engage the 2 guides to install the front bumper energy absorber.


Hide 52129B 7.INSTALL FRONT BUMPER LOWER COVER

a.

Engage the 14 claws.

B564111


b.

Install the front bumper lower cover to front bumper cover with the 4 clips.

B564110


Hide 52128B 8.INSTALL FRONT BUMPER HOLE COVER LH

a.
B564107C01
0.906,1.469 1.208,1.25 true 0.708,1.375 0.927,1.552 0.219,0.177 10 true *a
*a Hook


Engage the hook.


b.

Engage the 2 claws to install the front bumper hole cover LH.


Hide 52127D 9.INSTALL FRONT BUMPER HOLE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 81482C 10.INSTALL FOG LIGHT COVER LH

a.
B564106

Engage the 2 claws.


b.
B564105

Install the fog light cover LH with the 2 screws.


Hide 81481E 11.INSTALL FOG LIGHT COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 53101 12.INSTALL RADIATOR GRILLE SUB-ASSEMBLY

a.

Engage the 3 guides and 10 clips.

B564104


b.

Install the radiator grille sub-assembly with the 2 screws.

B564103


Hide 52526E 13.INSTALL NO. 1 FRONT BUMPER LOWER RETAINER

a.
B564102

Install the No. 1 front bumper lower retainer with the screw.


Hide 75311 14.INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM

a.
B564101

Engage the 2 claws.


b.
B564100

Install the radiator grille (or front panel) emblem with the 2 screws.


Hide 52711 15.INSTALL FRONT BUMPER MOULDING

a.

Engage the 3 guides and 8 clips.

B564099


b.

Install the front bumper moulding with the 2 screws.

B564098


Hide 53115B 16.INSTALL RADIATOR GRILLE BRACKET

a.

Engage the 6 guides.

B564097


b.

Engage the 3 guides and 4 claws.

B564096


c.

Install the 10 screws and 2 clips.

B564095C01
0,0 0,0 false
V100135

Screw
V100136

Clip



d.

Install the radiator grille bracket with the 2 clips.

B564093


Hide 53395H 17.INSTALL HOOD TO RADIATOR GRILLE SEAL

a.

Connect the hood to radiator grille seal as shown in the illustration.

B564092

HINT:

Use the same procedure for the LH side and RH side.



b.

Engage the 16 clips to install the hood to radiator grille seal.


Hide 52114A 18.INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET

a.
B570452

Install the front bumper extension mounting bracket with the 2 screws.


Hide 19.INSTALL ULTRASONIC SENSOR CLIP

HINT:

When installing the ultrasonic sensor clip, heat the front bumper cover using a heat light.


Heating Temperature:
Item Temperature
Front Bumper Cover 20 to 30 °C (68 to 86 °F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front bumper cover excessively.


a.

Clean the front bumper cover surface.

i.

Using a heat light, heat the front bumper cover surface.


ii.

Remove the double-sided tape from the front bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B471319C03
0,0 0,0 false
V100144

Primer


Using a brush or felt, apply primer or equivalent to the ultrasonic sensor clip installation area.


c.

Install a new ultrasonic sensor clip.

i.

Using a heat light, heat the front bumper cover surface.


ii.

Remove the release paper from the ultrasonic sensor clip.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.

Install each ultrasonic sensor clip as shown in the illustration.

B564089C01
1.24,1.688 1.625,1.823 true 5.802,2.625 5.802,3.052 true 1.375,2.635 1.375,3.063 true 6.167,0.948 6.167,0.76 true 1.26,3.083 1.531,3.292 0.271,0.208 12 true *A 5.708,3.052 5.979,3.26 0.271,0.208 12 true *A 0.948,1.552 1.219,1.76 0.271,0.208 12 true *A 6.083,0.948 6.281,1.135 0.198,0.188 10 true *a
*A w/ TOYOTA Parking Assist-sensor System - -
*a Line - -


HINT:
·

Install the ultrasonic sensor clip within the line on the front bumper cover.

·

Press the ultrasonic sensor clip firmly to install it.





Hide 82114 20.INSTALL NO. 4 ENGINE ROOM WIRE (w/o TOYOTA Parking Assist-sensor System)

a.

w/ Pre-collision System:

i.

Engage the 9 clamps to install the No. 4 engine room wire.

B564086



Hide 82114 21.INSTALL NO. 4 ENGINE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)

a.

Engage each clamp to install the No. 4 engine room wire.

B564087C01
3.802,0.667 3.604,1.292 3.604,1.292 3.594,0.781 true 3.49,1.313 3.75,1.51 0.26,0.198 12 true *A
*A w/ Panoramic View Monitor System - -



Hide 85370A 22.INSTALL NO. 1 HEADLIGHT CLEANER WASHER HOSE ASSEMBLY (w/ Headlight Cleaner System)

a.

Engage the 10 clamps to install the No. 1 headlight cleaner washer hose assembly.

B570451


Hide 85208A 23.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

Hide 85207A 24.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:

Use the same procedure as for the LH side.


Hide 85354 25.INSTALL HEADLIGHT WASHER COVER LH (w/ Headlight Cleaner System)

Hide 85353 26.INSTALL HEADLIGHT WASHER COVER RH (w/ Headlight Cleaner System)

HINT:

Use the same procedure as for the LH side.


Hide 89347B 27.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89347C 28.INSTALL FRONT CENTER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89341K 29.INSTALL FRONT CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89341L 30.INSTALL FRONT CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 86790B 31.INSTALL FRONT TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)

Hide 88211B 32.INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-collision System)

Hide 81220 33.INSTALL FOG LIGHT ASSEMBLY LH

Hide 81210A 34.INSTALL FOG LIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.