Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WINDSHIELD OUTSIDE MOULDING
RM37A0E _59 Vehicle Exterior _086903 EXTERIOR PANELS / TRIM _0417667 WINDSHIELD OUTSIDE MOULDING A

EXTERIOR PANELS / TRIM  WINDSHIELD OUTSIDE MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75547C 1.INSTALL NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP

HINT:

Perform the following procedure only when replacement of a No. 3 windshield outside moulding clip is necessary.


a.
B565968

Using a riveter with a nose piece, install 5 new No. 3 windshield outside moulding clips.

HINT:

If the mandrel of the No. 3 windshield outside moulding clip does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.


NOTICE:
B398365C01
1.75,0.75 1.5,0.25 1.5,0.25 1.333,0.25 false 1.833,1.833 2.021,1.333 false 1.156,0.156 1.469,0.313 0.313,0.156 10 false *a 1.76,1.844 2.073,2 0.313,0.156 10 false *b 2.167,0.167 2.479,0.323 0.313,0.156 10 false *c
*a Riveter
*b Mandrel
*c Incorrect


·

Do not pry the No. 3 windshield outside moulding clip with the riveter, as this will cause damage to the riveter and mandrel.


·
B398364C02
1.031,0.333 1.281,0.333 false 1.083,1.396 1.333,1.396 false 1.313,0.26 1.625,0.417 0.313,0.156 10 false *a 0.083,0.104 0.427,0.469 0.344,0.365 10 false *b 1.375,1.313 1.688,1.469 0.313,0.156 10 false *a 0.125,1.125 0.51,1.438 0.385,0.313 10 false *c
*a Riveter
*b Incorrect
*c Correct


Confirm that the No. 3 windshield outside moulding clips are seated properly against the vehicle body.


·

Do not tilt the riveter when installing the No. 3 windshield outside moulding clip to the vehicle body.




b.

Install the windshield glass sub-assembly.

Click hereVehicle Exterior>WINDOW / GLASS>WINDSHIELD GLASS>INSTALLATION


Hide 75545B 2.INSTALL NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP

HINT:

Perform the following procedure only when replacement of a No. 1 windshield outside moulding clip is necessary.


a.

Engage the 5 claws to install the 5 No. 1 windshield outside moulding clips as shown in the illustration.

B565969C01
0,0 0,0 false
V113147

Install in this Direction - -



Hide 75534 3.INSTALL WINDSHIELD OUTSIDE MOULDING

a.

Engage the 10 claws to install the windshield outside moulding.


Hide 53896A 4.INSTALL FRONT FENDER FRONT SPLASH SHIELD

HINT:

When installing the front fender front splash shield, heat the vehicle body using a heat light.


Heating Temperature:
Item Temperature
Vehicle Body 20 to 30 °C (68 to 86 °F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove any double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new front fender front splash shield.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the release paper from the front fender front splash shield.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.

Engage the 2 claws and attach the double-sided tape to install the front fender front splash shield.

HINT:

Press the front fender front splash shield firmly to install it.




Hide 53867H 5.INSTALL FRONT FENDER TO COWL SIDE SEAL