When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, front camera system, lane control system, road sign assist system, pre-collision system, lighting system (EXT) may not operate properly due to a difference in the transmissivity or black ceramic border.
56115A
1.INSTALL NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)
Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.
Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.
56116C
2.INSTALL NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)
Using a brush or sponge, coat the installation area of 2 new No. 2 windshield glass stoppers with glass primer.
Do not apply too much glass primer.
Allow the glass primer to dry for 3 minutes or more.
Throw away any leftover glass primer.
If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.
| *A | Back Side |
| *a | Ceramic Notch |
| *b | Windshield Glass Edge Side |
Install the 2 No. 2 windshield glass stoppers to the windshield glass as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 13.7 to 14.7 mm (0.539 to 0.579 in.) |
Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.
75531F
3.INSTALL WINDSHIELD OUTSIDE UPPER MOULDING
Using a brush or sponge, coat the installation area of a new windshield outside upper moulding with glass primer.
Do not apply too much glass primer.
Allow the glass primer to dry for 3 minutes or more.
Throw away any leftover glass primer.
If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.
Install the windshield outside upper moulding to the windshield glass as shown in the illustration.
| *A | Back Side | - | - |
| *a | Alignment Position (Edge Of Curved Surface) | - | - |
| Area | Measurement | Area | Dimension |
|---|---|---|---|
| a | 2.0 mm (0.0787 in.) | b | 7.0 mm (0.276 in.) |
56117A
4.INSTALL WINDOW GLASS ADHESIVE DAM
Using a brush or sponge, coat the installation area of 3 new window glass adhesive dams with glass primer.
Do not apply too much glass primer.
Allow the glass primer to dry for 3 minutes or more.
Throw away any leftover glass primer.
If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.
Install the window glass adhesive dam to the windshield glass as shown in the illustration.
| *A | Back Side | - | - |
| *a | Indicated Line | *b | Alignment Position (End of Indicated Line) |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| a | 20.0 mm (0.787 in.) | b | 5.0 mm (0.197 in.) |
Install the 2 window glass adhesive dams to the windshield glass as shown in the illustration.
| *A | Back Side | - | - |
| *a | Indicated Line | *b | Alignment Position (End of Indicated Line) |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| a | 5.0 mm (0.197 in.) | b | 8.0 mm (0.315 in.) |
56153C
5.INSTALL FRONT WINDOW INNER CENTER MOULDING
Perform the following procedure only when replacement of the front window inner center moulding is necessary.
| *A | Back Side |
|
Glass Primer |
Using a brush or sponge, coat the installation area of a new front window inner center moulding with glass primer.
| Area | Dimension |
|---|---|
| a | 17.5 to 20.5 mm (0.689 to 0.807 in.) |
Do not apply too much glass primer.
Allow the glass primer to dry for 3 minutes or more.
Throw away any leftover glass primer.
If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.
Install the front window inner center moulding to the windshield glass as shown in the illustration.
| *A | Back Side | - | - |
| *a | Alignment Mark (Ceramic Notch) | *b | Matchmark |
| Area | Measurement | Area | Dimension |
|---|---|---|---|
| a | 2.0 mm (0.0787 in.) | b | 0 to 0.6 mm (0 to 0.0236 in.) |
Do not damage the front window inner center moulding.
6.INSTALL WINDSHIELD GLASS SUB-ASSEMBLY
| *a | Matchmark |
Position the windshield glass sub-assembly.
Using suction cups, place the windshield glass sub-assembly in the correct position.
Check that the whole contact surface of the windshield glass sub-assembly rim is perfectly even.
Align the matchmarks on the windshield glass sub-assembly and vehicle body.
Check that the windshield glass stoppers are engaged to the vehicle body correctly.
Remove the windshield glass sub-assembly.
Using a brush, coat the installation surface on the vehicle body with body primer.
Do not coat the adhesive with body primer.
Do not apply too much body primer.
Allow the body primer to dry for 3 minutes or more.
Throw away any leftover body primer.
If an area other than specified is coated by accident, wipe off the body primer with a clean piece of cloth before it dries.
Using a brush or sponge, coat the adhesive application area with glass primer.
| *A | Back Side | - | - |
| *a | Adhesive Application Area | - | - |
|
Glass Primer | - | - |
| Area | Dimension | - | - |
|---|---|---|---|
| a | 8.0 mm (0.315 in.) or more | - | - |
Do not apply too much glass primer.
Allow the glass primer to dry for 3 minutes or more.
Throw away any leftover glass primer.
Apply glass primer to the ceramic notches.
If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.
Apply adhesive to the windshield glass sub-assembly.
Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent
| *a | Nozzle |
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 12.0 to 15.0 mm (0.472 to 0.591 in.) |
| b | 8.0 to 11.0 mm (0.315 to 0.433 in.) |
Load the sealer gun with the cartridge.
Apply adhesive to the windshield glass sub-assembly as shown in the illustration.
| *A | Back Side | - | - |
| *a | Adhesive Positioning Center | - | - |
|
Adhesive | - | - |
| Area | Dimension | Area | Dimension |
|---|---|---|---|
| a | 9.5 mm (0.374 in.) | b | 5.0 mm (0.197 in.) |
| c | 6.5 mm (0.256 in.) | d | 53.8 mm (2.12 in.) |
Apply adhesive to the ceramic notches.
| *a | Matchmark |
Install the windshield glass sub-assembly.
Using suction cups, position the windshield glass sub-assembly so that the matchmarks are aligned, and press it in gently along the rim.
Check that the windshield glass stoppers are engaged to the vehicle body correctly.
Check the clearance between the vehicle body and windshield glass sub-assembly.
Lightly press the outer surface of the windshield glass sub-assembly to ensure that the windshield glass sub-assembly is securely fit to the vehicle body.
Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.
Using a scraper, remove any excess or protruding adhesive.
Hold the windshield glass sub-assembly using protective tape until the applied adhesive becomes hard.
Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.
When replacing the windshield glass sub-assembly or front window inner center moulding with a new one:
Remove the 2 protective retainers from the front window inner center moulding.
Do not damage the front window inner center moulding.
Make sure to remove the protective retainers.
w/ Windshield Deicer System:
Connect the connector.
7.INSPECT FOR LEAK
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
8.INSTALL ROOF HEADLINING ASSEMBLY
Return the front section of the roof headlining assembly to its original position.
Connect the connector.
74348
9.INSTALL VISOR HOLDER
74320
10.INSTALL VISOR ASSEMBLY LH
74325
11.INSTALL VISOR BRACKET COVER (for LH Side)
74610A
12.INSTALL ASSIST GRIP SUB-ASSEMBLY
74310
13.INSTALL VISOR ASSEMBLY RH
Use the same procedure as for the LH side.
74325
14.INSTALL VISOR BRACKET COVER (for RH Side)
Use the same procedure as for the LH side.
62212B
15.INSTALL FRONT PILLAR GARNISH ASSEMBLY LH
62211U
16.INSTALL FRONT PILLAR GARNISH ASSEMBLY RH
Use the same procedure as for the LH side.
81260A
17.INSTALL MAP LIGHT ASSEMBLY
8646C
18.INSTALL FORWARD RECOGNITION CAMERA
89941
19.INSTALL RAIN SENSOR (w/ Rain Sensor)
87810
20.INSTALL INNER REAR VIEW MIRROR ASSEMBLY
w/ EC Mirror: Click hereVehicle Interior>MIRROR (INT)>INNER REAR VIEW MIRROR (w/ EC Mirror)>INSTALLATION
w/o EC Mirror: Click hereVehicle Interior>MIRROR (INT)>INNER REAR VIEW MIRROR (w/o EC Mirror)>INSTALLATION
75534
21.INSTALL WINDSHIELD OUTSIDE MOULDING LH
75533
22.INSTALL WINDSHIELD OUTSIDE MOULDING RH
Use the same procedure as for the LH side.
55708
23.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY