Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK › 2020.02–2020.11
RM37A0E _58 Vehicle Interior _086884 DOOR LOCK _0417743 FRONT DOOR LOCK A

DOOR LOCK  FRONT DOOR LOCK  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door lock with motor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 58441L 2.REMOVE BATTERY SERVICE HOLE COVER (for HV Model)

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 67492A 4.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

Hide 5.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Hide 6.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Hide 69278B 7.REMOVE FRONT DOOR INSIDE HANDLE BEZEL

Hide 81230N 8.REMOVE COURTESY LIGHT ASSEMBLY

Hide 67602 9.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 67869J 10.REMOVE FRONT DOOR WEATHERSTRIP CLIP

Hide 67832 11.REMOVE FRONT DOOR SERVICE HOLE COVER

Hide 69040A 12.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY

a.
B563675C01
2.802,2.573 3.031,2.844 true 3.052,2.781 3.24,2.969 0.188,0.188 10 true *1
*1 Front Door Lock Open Rod
V113147

Remove in this Direction


Using a T30 "TORX" socket wrench, remove the 3 screws.


b.

Slide the front door lock with motor assembly downward as shown in the illustration to disconnect the front door lock open rod and remove the front door lock with motor assembly and cables as a unit.


c.

When reusing the front door lock with motor assembly:

i.
B563676

Remove the door lock wiring harness seal from the front door lock with motor assembly.



Hide 69036A 13.REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY

a.
B563677

Using a screwdriver, disengage the 2 claws as shown in the illustration.


b.
B563678C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws to remove the front door lock cover sub-assembly as shown in the illustration.


Hide 69720B 14.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B563679C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door lock remote control cable assembly as shown in the illustration.


Hide 69760C 15.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B563680C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door inside locking cable assembly as shown in the illustration.