Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM (for HV Model)
RM37A0E _51 Engine / Hybrid System _086858 CRUISE CONTROL _0417900 CRUISE CONTROL SYSTEM(for HV Model) J

CRUISE CONTROL  CRUISE CONTROL SYSTEM(for HV Model)  Steering Pad Switch Circuit  


DESCRIPTION

·

The steering pad switch assembly outputs the on/off signal and various control signals to the hybrid vehicle control ECU.

·

The hybrid vehicle control ECU performs cruise control according to the signals received from the steering pad switch assembly.


WIRING DIAGRAM

A408160E36
5.417,3.438 7.156,3.708 1.74,0.271 10 false Hybrid Vehicle Control ECU 5.844,0.76 6.302,0.958 0.458,0.198 10 false 14 6.094,0.885 6.552,1.083 0.458,0.198 10 false CCS 4.344,0.875 4.802,1.073 0.458,0.198 10 false H24 4.344,2.073 4.802,2.271 0.458,0.198 10 false H24 4.375,0.646 4.833,0.844 0.458,0.198 10 false 13 4.427,1.854 4.885,2.052 0.458,0.198 10 false 2 3.385,2.573 4.49,3.063 1.104,0.49 10 false Spiral Cable Sub-assembly 3.75,1.99 4.208,2.188 0.458,0.198 10 false ECC 3.74,0.771 4.198,0.969 0.458,0.198 10 false CCS 3.229,0.865 3.688,1.063 0.458,0.198 10 false z1 3.229,2.063 3.688,2.26 0.458,0.198 10 false z1 3.229,1.854 3.688,2.052 0.458,0.198 10 false 12 3.271,0.656 3.729,0.854 0.458,0.198 10 false 2 0.823,2.573 2.781,2.906 1.958,0.333 10 false Steering Pad Switch Assembly 2.76,1.948 3.219,2.146 0.458,0.198 10 false ECC 2.76,0.76 3.219,0.958 0.458,0.198 10 false CCS 0.458,1.5 0.917,1.698 0.458,0.198 10 false -SET 1.24,1.5 1.698,1.698 0.458,0.198 10 false +RES 1.813,1.5 2.563,1.75 0.75,0.25 10 false CANCEL 2.521,1.5 3.271,1.75 0.75,0.25 10 false MAIN 5.417,3.26 5.875,3.458 0.458,0.198 10 false H67 1,2.219 4.979,2.417 3.979,0.198 10 false Cruise Control Switch

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Cancel Switch CANCEL switch status OFF or ON OFF: CANCEL switch not pushed
ON: CANCEL switch pushed
-
-SET Switch -SET switch status OFF or ON OFF: -SET switch not pushed
ON: -SET switch pushed
-
+RES Switch +RES switch status OFF or ON OFF: +RES switch not pushed
ON: +RES switch pushed
-
Cruise Main Switch Operation Condition Cruise control main switch status OFF or ON OFF: Cruise control main switch not pushed
ON: Cruise control main switch pushed
-
Powertrain > Cruise Control > Data List
Tester Display
Cancel Switch
-SET Switch
+RES Switch
Cruise Main Switch Operation Condition
50003 399 21,22,23,1
OK:

The value of each Data List item changes according to the operation of the steering pad switch assembly.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU AND BODY GROUND)
a.

Disconnect the H67 hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H24-13 (CCS) - H67-14 (CCS) Always Below 1 Ω
H24-2 (ECC) - Body ground Always Below 1 Ω
H24-13 (CCS) or H67-14 (CCS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR