Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM (for Gasoline Model)
RM37A0E _51 Engine / Hybrid System _086858 CRUISE CONTROL _0417901 CRUISE CONTROL SYSTEM(for Gasoline Model) C

CRUISE CONTROL  CRUISE CONTROL SYSTEM(for Gasoline Model)  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. When the ECM receives this signal, it cancels control of vehicle speed by the cruise control system. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light switch signal circuit. The cancellation condition occurs when voltage is applied to the terminal STP. When the brake pedal is depressed, voltage is applied to the terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM cancels control of vehicle speed by the cruise control system.

DTC No. Detection Item DTC Detection Condition Trouble Area
P057162 Brake Switch "A" Signal Compare Failure When the ignition switch is ON and the cruise control system is operating, the voltage of the STP and ST1- terminals of the ECM are less than 1 V for 0.5 seconds or more.
·

Stop light switch assembly

·

Harness or connector

·

ECM



WIRING DIAGRAM

A451008E12
5.625,2.427 6.833,2.875 1.208,0.448 10 false ECM 3.125,2.458 5.417,2.656 2.292,0.198 10 false Stop Light Switch Assembly 3.583,1.417 3.74,1.615 0.156,0.198 10 false B 3.573,0.917 3.729,1.115 0.156,0.198 10 false B 4.177,0.792 4.333,0.99 0.156,0.198 10 false L 4.177,1.594 4.333,1.792 0.156,0.198 10 false L 3.563,1.927 3.99,2.125 0.427,0.198 10 false GND 2.146,1.552 3.146,1.823 1,0.271 10 false ECU-IG2 NO. 3 2.396,1.073 3.396,1.344 1,0.271 10 false STOP 0.323,0.917 2.01,1.115 1.688,0.198 10 false from J/B-B Fuse 0.031,1.417 1.719,1.615 1.688,0.198 10 false from IG2-NO. 2 Relay 3.385,0.813 3.542,1.01 0.156,0.198 10 false 7 3.385,1.313 3.542,1.51 0.156,0.198 10 false 6 3.385,1.813 3.542,2.01 0.156,0.198 10 false 2 4.333,1.49 4.49,1.688 0.156,0.198 10 false 5 4.333,0.688 4.49,0.885 0.156,0.198 10 false 3 3.135,2.302 3.594,2.521 0.458,0.219 10 false A42 5.625,2.281 6.083,2.5 0.458,0.219 10 false A28 5.396,0.667 5.698,0.896 0.302,0.229 10 false 27 5.396,1.458 5.729,1.677 0.333,0.219 10 false 42 5.667,0.688 6.125,0.885 0.458,0.198 10 false STP 5.677,1.469 6.135,1.667 0.458,0.198 10 false ST1- 2.542,2.979 3.865,3.177 1.323,0.198 10 false to Each ECU

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the ECM, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE AND BODY GROUND)
a.
C401044C84
1.5,0.25 1.833,0.5 0.333,0.25 1.24,1.833 1.406,1.25 true 2.177,1.833 2.01,1.25 true 2.427,1.833 2.177,1.25 true 1.552,0.302 2.01,0.5 0.458,0.198 10 false A42 1.083,1.844 1.479,2.073 0.396,0.229 10 false GND 2.167,1.844 2.385,2.063 0.219,0.219 10 false B 2.417,1.844 2.635,2.063 0.219,0.219 10 false B 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the A42 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-7 (B) - Body ground Always 11 to 14 V
A42-6 (B) - Body ground Ignition switch ON 11 to 14 V
A42-6 (B) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A42 stop light switch assembly connector.


b.

Disconnect the A28 ECM connector.


c.

Disconnect each ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-3 (L) - A28-27 (STP) Always Below 1 Ω
A42-5 (L) - A28-42 (ST1-) Always Below 1 Ω
A42-3 (L) or A28-27 (STP) - Body ground Always 10 kΩ or higher
A42-5 (L) or A28-42 (ST1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR