Use the following procedure to troubleshoot the pre-collision system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
for HV Model
Measure the auxiliary battery voltage with the ignition switch off.
11 to 14 V
If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.
for Gasoline Model
Measure the auxiliary battery voltage.
11 to 14 V
If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.
Check the fuses and relays.
Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
| Proceed to |
|---|
| NEXT |
NEXT
Check if a pre-collision system warning message is displayed on the multi-information display in the combination meter assembly.
If more than one message is displayed, perform each inspection in the order listed in the table.
| Result | Proceed to |
|---|---|
| "VSC Turned OFF Pre-Collision Brake System Unavailable" is displayed | A |
| "Pre-Collision System Malfunction Visit Your Dealer" is displayed | B |
| "Pre-Collision System Unavailable Clean Sensor" is displayed | C |
| Any of the following messages is displayed:
·
"Pre-Collision System Unavailable" ·
"Pre-Collision System Unavailable Clean Sensor" ·
"Front Camera Unavailable" ·
"Front Camera Unavailable See Owner's Manual" |
D |
| Warning message is not displayed | E |
A
B
C
D
E
Using the GTS, check if the CAN communication system is functioning normally.
Refer to CAN Bus Check in CAN Communication System.
for HV Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM
for Gasoline Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM
CAN communication system is functioning normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for HV Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING
for Gasoline Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING
Using the GTS, check for DTCs.
Make a note of the output DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC C142571 is output | B |
| DTCs other than C142571 are output | C |
A
B
C
Using the GTS, check for Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Record any output Vehicle Control History (RoB).
| Result | Proceed to |
|---|---|
| Vehicle Control History (RoB) codes are not output | A |
| Vehicle Control History (RoB) code X2013, X2015, X2022, X2024, X2025, X2026 or X2028 is output | B |
| Vehicle Control History (RoB) codes other than X2013, X2015, X2022, X2024, X2025, X2026 and X2028 are output | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Using the GTS, clear the Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Using the GTS, check for Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Result | Proceed to |
|---|---|
| Vehicle Control History codes (RoB) are not output | A |
| Vehicle Control History codes (RoB) are output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Using the GTS, clear the DTCs.
Reproduce the vehicle conditions that were present when the DTCs that were noted were stored.
Refer to each corresponding DTC for details on the detection conditions.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Using the GTS, check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Check that there is no foreign matter such as dirt on or around the millimeter wave radar sensor assembly.
A cover other than the dedicated radar sensor cover is not installed.
There is no dirt on the radar sensor cover or millimeter wave radar sensor assembly.
An accessory, such as bull bars, a grille guard, etc., which interferes with millimeter radio waves is not installed.
There is no sticker or coating applied to the dedicated radar sensor cover.
There is no foreign matter between the radar sensor cover and millimeter wave radar sensor assembly.
If a problem is found, correct the problem as necessary.
| Proceed to |
|---|
| NEXT |
NEXT
Before checking if the pre-collision system warning message is displayed on the multi-information, turn the ignition switch off then to ON.
Turn the ignition switch off.
Turn the ignition switch to ON.
Check if "Pre-Collision System Unavailable Clean Sensor" is displayed on the multi-information display.
| Result | Proceed to |
|---|---|
| Not displayed | A |
| Displayed | B |
A
B
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| On-Line Calibration Angle (Horizontal) | Calibrated angle value (horizontal) | Min.: -12.8 deg, Max.: 12.7 deg | Learned value | - |
| Tester Display |
|---|
| On-Line Calibration Angle (Horizontal) |
The displayed value is between -0.5 and 0.5 degrees.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Explain to the customer that "Pre-Collision System Unavailable Clean Sensor" was temporarily displayed on the multi-information display due to foreign matter such as dirt on or around the millimeter wave radar sensor assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Refer to Problem Symptoms Table for the pre-collision system.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| Problem symptoms are not listed in the Problem Symptoms Table. | A |
| Problem symptoms are listed in the Problem Symptoms Table. | B |
A
B
Check the condition of the warning lights.
| Result | Proceed to |
|---|---|
| The PCS warning light is not illuminated | A |
| Only the PCS warning light is illuminated | B |
A
B
Using the GTS, check for DTCs (Confirmed).
Make a note of the output DTCs (Confirmed).
| Result | Proceed to |
|---|---|
| DTCs (Confirmed) are not output | A |
| DTCs (Confirmed) are output | B |
A
B
Using the GTS, check for Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Record any output Vehicle Control History (RoB).
| Result | Proceed to |
|---|---|
| Vehicle Control History codes (RoB) are not output | A |
| Vehicle Control History codes (RoB) are output | B |
A
B
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>VEHICLE CONTROL HISTORY
By using information obtained from the customer problem analysis and vehicle control history such as time of detection, trip number, etc., it may be possible to determine the cause of the malfunction.
Check if the exception conditions for the pre-collision system were met.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>PRECAUTION
| Result | Proceed to |
|---|---|
| The exception conditions were not met. | A |
| The exception conditions were met. | B |
A
B
Before checking for millimeter wave radar sensor beam axis misalignment, make sure that the radiator grille and front bumper are correctly installed and have not been damaged or modified.
Adjust the reflector height.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
Place the reflector.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Front Radar Sensor / Utility / Front Beam Axis Misalignment Reading.
| Tester Display |
|---|
| Front Beam Axis Misalignment Reading |
Check the amount of misalignment.
| Vertical Direction | -5 to 5 deg. |
| Horizontal Direction | -0.6 to 0.6 deg. |
The millimeter wave radar sensor assembly automatically calibrates the beam axis while the vehicle is being driven. The specified values apply to the automatic calibration only and do not apply during manual beam axis adjustment of the millimeter wave radar sensor assembly.
| Result | Proceed to |
|---|---|
| The beam axis values are within specification. | A |
| The beam axis values are not within specification. | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Refer to each corresponding DTC (Confirmed) for details on the detection conditions.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
| Proceed to |
|---|
| NEXT |
NEXT