The forward recognition camera receives vehicle information from the hybrid vehicle control ECU via CAN communication.
If the forward recognition camera cannot store the vehicle information, it will store this DTC.
The forward recognition camera receives vehicle information from the ECM via CAN communication.
If the forward recognition camera cannot store the vehicle information, it will store this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| U030051 | Internal Control Module Software Incompatibility Not Programmed | for HV Model
When the ignition switch is ON for 3 seconds or more, the vehicle information sent from the hybrid vehicle control ECU cannot be verified by the forward recognition camera for 3 seconds or more. for Gasoline Model
When the ignition switch is ON for 3 seconds or more, the vehicle information sent from the ECM cannot be verified by the forward recognition camera for 3 seconds or more. |
for HV Model
·
Hybrid control system ·
Forward recognition camera ·
Hybrid vehicle control ECU for Gasoline Model
·
SFI system ·
Forward recognition camera ·
ECM |
Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.*1
Before replacing the ECM, refer to Service Bulletin.*2
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.
If the forward recognition camera has been replaced with a new one, forward recognition camera adjustment must be performed.
Forward recognition camera adjustment can be performed by using either One Time Recognition or Sequential Recognition.
One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)
Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
*1: for HV Model
*2: for Gasoline Model
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for HV Model | A |
| for Gasoline Model | B |
A
B
Using the GTS, check for hybrid control system DTCs.
| Result | Proceed to |
|---|---|
| Hybrid control system DTCs are not output | A |
| Hybrid control system DTCs are output | B |
A
B
for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>HOW TO PROCEED WITH TROUBLESHOOTING
for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>HOW TO PROCEED WITH TROUBLESHOOTING
Check DTCs.
Turn the ignition switch off.
DTCs indicating a vehicle information mismatch with the hybrid vehicle control ECU are not output by any ECU other than the forward recognition camera.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Information (Conv/HV) | Vehicle information (Conv/HV) | Unknown / Conv / HV | Unknown: Vehicle information not confirmed
Conv: Conventional HV: Hybrid vehicle |
- |
| Tester Display |
|---|
| Vehicle Information (Conv/HV) |
If the vehicle information stored in the forward recognition camera is different than the actual vehicle specifications, the vehicle information stored in the forward recognition camera may be incorrect. Check for DTCs and replace the forward recognition camera if necessary.
If the vehicle information stored in the forward recognition camera matches the actual vehicle specifications, the installed hybrid vehicle control ECU is incompatible. Replace the hybrid vehicle control ECU with a correct one.
| Result | Proceed to |
|---|---|
| Vehicle information stored in forward recognition camera and actual vehicle specifications do not match | A |
| "Unknown" is displayed | |
| Vehicle information stored in forward recognition camera and actual vehicle specifications match | B |
A
B
Using the GTS, check for SFI system DTCs.
| Result | Proceed to |
|---|---|
| SFI system DTCs are not output | A |
| SFI system DTCs are output | B |
A
B
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check DTCs.
Turn the ignition switch off.
DTCs indicating a vehicle information mismatch with the ECM are not output by any ECU other than the forward recognition camera.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Information (Conv/HV) | Vehicle information (Conv/HV) | Unknown / Conv / HV | Unknown: Vehicle information not confirmed
Conv: Conventional HV: Hybrid vehicle |
- |
| Tester Display |
|---|
| Vehicle Information (Conv/HV) |
If the vehicle information stored in the forward recognition camera is different than the actual vehicle specifications, the vehicle information stored in the forward recognition camera may be incorrect. Check for DTCs and replace the forward recognition camera if necessary.
If the vehicle information stored in the forward recognition camera matches the actual vehicle specifications, the installed ECM is incompatible. Replace the ECM with a correct one.
| Result | Proceed to |
|---|---|
| Vehicle information stored in forward recognition camera and actual vehicle specifications do not match | A |
| "Unknown" is displayed | |
| Vehicle information stored in forward recognition camera and actual vehicle specifications match | B |
A
B