Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM (for HV Model)
RM37A0E _51 Engine / Hybrid System _086858 CRUISE CONTROL _0418319 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for HV Model) C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for HV Model)  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly outputs a signal to the hybrid vehicle control ECU. The hybrid vehicle control ECU uses this signal to control cancellation of vehicle speed by the dynamic radar cruise control. When the hybrid vehicle control ECU determines that terminals STP and ST1 of the stop light switch assembly are both less than 1 V, DTC P057162 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
P057162 Brake Switch "A" Signal Compare Failure When the ignition switch is ON and the dynamic radar cruise control system is operating, the hybrid vehicle control ECU detects that the voltage at terminal STP and ST1- are both less than 1 V for approximately 0.5 seconds or more.
·

Harness or connector

·

Stop light switch assembly

·

Hybrid vehicle control ECU


Cruise Control

WIRING DIAGRAM

A455567E03
0.49,0.875 2.781,1.073 2.292,0.198 10 false from J/B-B Fuse 2.26,1.542 4.552,1.74 2.292,0.198 10 false ECU-IG2 NO. 3 0.188,1.365 2.479,1.563 2.292,0.198 10 false from IG2-NO. 2 Relay 3.073,2.469 5.365,2.667 2.292,0.198 10 false Stop Light Switch Assembly 3.083,2.313 5.375,2.51 2.292,0.198 10 false A42 5.865,2.292 6.781,2.958 0.917,0.667 10 false Hybrid Vehicle Control ECU 2.49,1.063 2.958,1.26 0.469,0.198 10 false STOP 4.25,0.771 4.76,1.115 0.51,0.344 10 false L 5.781,0.635 6.354,0.896 0.573,0.26 10 false STP 3.656,1.896 4.49,2.167 0.833,0.271 10 false GND 4.448,0.646 6.74,0.844 2.292,0.198 10 false 3 5.375,1.552 7.125,1.854 1.75,0.302 10 false A32 4.438,1.427 6.729,1.625 2.292,0.198 10 false 5 2.667,2.958 4.958,3.156 2.292,0.198 10 false to Each ECU 3.656,1.396 4.427,1.792 0.771,0.396 10 false B 5.375,0.771 7.146,1.042 1.771,0.271 10 false A31 3.49,1.781 5.781,1.979 2.292,0.198 10 false 2 5.76,1.427 7.146,1.677 1.385,0.25 10 false ST1- 3.469,0.76 5.76,0.958 2.292,0.198 10 false 7 3.469,1.281 5.76,1.479 2.292,0.198 10 false 6 3.656,0.896 4.427,1.292 0.771,0.396 10 false B 4.25,1.563 4.76,1.906 0.51,0.344 10 false L 5.448,0.542 5.729,0.74 0.281,0.198 10 false 7 5.417,1.333 5.698,1.531 0.281,0.198 10 false 28

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE AND BODY GROUND)
C401044C79
1.5,0.25 1.833,0.5 0.333,0.25 1.24,1.833 1.406,1.25 true 2.177,1.833 2.01,1.25 true 2.427,1.833 2.177,1.25 true 1.552,0.302 2.01,0.5 0.458,0.198 10 false A42 1.083,1.844 1.479,2.073 0.396,0.229 10 false GND 2.167,1.844 2.385,2.063 0.219,0.219 10 false B 2.417,1.844 2.635,2.063 0.219,0.219 10 false B 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


a.

Disconnect the A42 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-7 (B) - Body ground Ignition switch off 11 to 14 V
A42-6 (B) - Body ground Ignition switch ON 11 to 14 V
A42-6 (B) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - HYBRID VEHICLE CONTROL ECU)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the A42 stop light switch assembly connector.


b.

Disconnect the A31 and A32 hybrid vehicle control ECU connectors.


c.

Disconnect each ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-3 (L) - A31-7 (STP) Always Below 1 Ω
A42-5 (L) - A32-28 (ST1-) Always Below 1 Ω
A42-3 (L) or A31-7 (STP) - Body ground Always 10 kΩ or higher
A42-5 (L) or A32-28 (ST1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR