Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM (for Gasoline Model)
RM37A0E _51 Engine / Hybrid System _086858 CRUISE CONTROL _0418320 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for Gasoline Model) C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for Gasoline Model)  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly outputs a signal to the ECM. The ECM uses this signal to control cancellation of vehicle speed by the dynamic radar cruise control. When the ECM determines that terminals STP and ST1 of the stop light switch assembly are both less than 1 V, DTC P057162 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
P057162 Brake Switch "A" Signal Compare Failure When the ignition switch is ON and the dynamic radar cruise control system is operating, the ECM detects that the voltage at terminal STP and ST1- are both less than 1 V for approximately 0.5 seconds or more.
·

Harness or connector

·

Stop light switch assembly

·

ECM


Cruise Control

WIRING DIAGRAM

A451008E05
5.625,2.427 6.833,2.875 1.208,0.448 10 false ECM 3.125,2.458 5.417,2.656 2.292,0.198 10 false Stop Light Switch Assembly 3.583,1.417 3.74,1.615 0.156,0.198 10 false B 3.573,0.917 3.729,1.115 0.156,0.198 10 false B 4.177,0.792 4.333,0.99 0.156,0.198 10 false L 4.177,1.594 4.333,1.792 0.156,0.198 10 false L 3.563,1.927 3.99,2.125 0.427,0.198 10 false GND 2.146,1.552 3.146,1.823 1,0.271 10 false ECU-IG2 NO. 3 2.396,1.073 3.396,1.344 1,0.271 10 false STOP 0.323,0.917 2.01,1.115 1.688,0.198 10 false from J/B-B Fuse 0.031,1.417 1.719,1.615 1.688,0.198 10 false from IG2-NO. 2 Relay 3.385,0.813 3.542,1.01 0.156,0.198 10 false 7 3.385,1.313 3.542,1.51 0.156,0.198 10 false 6 3.385,1.813 3.542,2.01 0.156,0.198 10 false 2 4.333,1.49 4.49,1.688 0.156,0.198 10 false 5 4.333,0.688 4.49,0.885 0.156,0.198 10 false 3 3.135,2.302 3.594,2.521 0.458,0.219 10 false A42 5.625,2.281 6.083,2.5 0.458,0.219 10 false A28 5.396,0.667 5.698,0.896 0.302,0.229 10 false 27 5.396,1.458 5.729,1.677 0.333,0.219 10 false 42 5.667,0.688 6.125,0.885 0.458,0.198 10 false STP 5.677,1.469 6.135,1.667 0.458,0.198 10 false ST1- 2.542,2.979 3.865,3.177 1.323,0.198 10 false to Each ECU

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the ECM, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE AND BODY GROUND)
C401044C79
1.5,0.25 1.833,0.5 0.333,0.25 1.24,1.833 1.406,1.25 true 2.177,1.833 2.01,1.25 true 2.427,1.833 2.177,1.25 true 1.552,0.302 2.01,0.5 0.458,0.198 10 false A42 1.083,1.844 1.479,2.073 0.396,0.229 10 false GND 2.167,1.844 2.385,2.063 0.219,0.219 10 false B 2.417,1.844 2.635,2.063 0.219,0.219 10 false B 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


a.

Disconnect the A42 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-7 (B) - Body ground Always 11 to 14 V
A42-6 (B) - Body ground Ignition switch ON 11 to 14 V
A42-6 (B) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the A42 stop light switch assembly connector.


b.

Disconnect the A28 ECM connector.


c.

Disconnect each ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-3 (L) - A28-27 (STP) Always Below 1 Ω
A42-5 (L) - A28-42 (ST1-) Always Below 1 Ω
A42-3 (L) or A28-27 (STP) - Body ground Always 10 kΩ or higher
A42-5 (L) or A28-42 (ST1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR