Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › AIR FUEL RATIO SENSOR
RM37A0E _51 Engine / Hybrid System _086849 2GR-FKS ENGINE CONTROL _0418448 AIR FUEL RATIO SENSOR A

2GR-FKS ENGINE CONTROL  AIR FUEL RATIO SENSOR  INSTALLATION  


PROCEDURE

Hide 89467C 1.INSTALL AIR FUEL RATIO SENSOR (for Bank 1)

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A454810C01
1.26,0.281 1.417,0.281 1.417,0.281 1.615,0.646 false 2.448,0.302 2.698,0.521 0.25,0.219 10 false *a 0.958,0.198 1.281,0.417 0.323,0.219 10 false SST
*a Torque Wrench Fulcrum Length


Using SST, install the air fuel ratio sensor to the exhaust manifold assembly RH (TWC: Front Catalyst).

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.7 N*m (384 kgf*cm, 28 ft.*lbf)




Hide 17140 2.INSTALL EXHAUST MANIFOLD ASSEMBLY RH (TWC: Front Catalyst)

Hide 89467B 3.INSTALL AIR FUEL RATIO SENSOR (for Bank 2)

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A454807C01
1.698,1.177 1.698,0.74 true 0.51,1.406 0.729,1.583 0.219,0.177 10 true *a 1.563,1.188 1.917,1.385 0.354,0.198 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, install the air fuel ratio sensor to the exhaust manifold assembly LH (TWC: Front Catalyst).

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.7 N*m (384 kgf*cm, 28 ft.*lbf)




b.

Connect the air fuel ratio sensor connector.


c.

Engage the wire harness clamp.


Hide 5.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing an air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION