Home › Drivetrain › UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE › 2020.02–2020.11
RM37A0E _52 Drivetrain _086859 UA80F AUTOMATIC TRANSMISSION / TRANSAXLE _0418481 TRANSMISSION CONTROL CABLE A

UA80F AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission control cable assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

*2: Not necessary when ECM replaced with new one

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC is output (Click here)
Code registration Engine start function See Service Bulletin for the registration method
If transaxle compensation code read from ECM
·

Perform reset memory*2

·

Transfer transaxle compensation code

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
If transaxle compensation code not read from ECM
·

Perform reset memory*2

·

Reset transaxle compensation code

·

Perform road test to allow ECM to learn



NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

If the ECM has been struck or dropped, replace it.

·

Perform Vehicle Identification Number (VIN) or frame number registration when replacing the ECM.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>REGISTRATION



PROCEDURE

Hide 1.REMOVE BATTERY

Hide 74404B 3.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 55446A 5.REMOVE NO. 1 SWITCH HOLE BASE

Hide 55606 6.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 58816B 7.REMOVE FRONT CONSOLE BOX INSERT

Hide 33820B 8.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

Before removing the transmission control cable assembly, check that the shift lever is in N.


a.
C426819

Disconnect the transmission control cable assembly from the transmission floor shift assembly.


b.
C426820C01
0.365,1.313 0.552,1.521 0.188,0.208 10 true *a
*a Counterclockwise


Rotate the lock nut counterclockwise approximately 180° and, while holding the lock nut in that position, disconnect the transmission control cable assembly from the transmission floor shift assembly.


c.
C426637C01
1.677,2.344 1.917,2 1.917,2 2.083,2 false 2.115,1.875 2.438,2.083 0.323,0.208 10 false *a 2.969,3.146 3.229,3.365 0.26,0.219 10 false *b 3.146,0.729 3.344,0.958 0.198,0.229 10 true *c
*a Clip (A)
*b 45° to 60°
*c Clip (B)


While disengaging the clip (A) as shown in the illustration, disconnect the transmission control cable assembly from the transmission control shaft lever together with the clip (A).


d.

Remove the clip (B) and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.


e.
C426850

Remove the nut and disconnect the transmission control cable assembly from the vehicle body.


f.
C426851

Remove the 2 nuts and then remove the transmission control cable assembly from the vehicle body.