Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM37A0E _59 Vehicle Exterior _086885 DOOR / HATCH _0418593 POWER BACK DOOR SYSTEM C

DOOR / HATCH  POWER BACK DOOR SYSTEM  B2251  Back Door Closer Switch Malfunction  


DESCRIPTION

The multiplex network door ECU receives signals from the latch switch, position switch, pawl switch and back door courtesy switch, which are built into the back door lock with courtesy light switch assembly. Based on these signals, the latch position of the back door lock with courtesy light switch assembly is determined.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2251 Back Door Closer Switch Malfunction While the back door closer is operating, a malfunction in the position information from the back door courtesy switch is detected within a certain amount of time.
·

Back door lock with courtesy light switch assembly

·

Multiplex network door ECU

·

Wire harness or connector



WIRING DIAGRAM

B567146E02
4.969,1.927 5.427,2.125 0.458,0.198 10 false W18 4.99,0.76 5.448,0.958 0.458,0.198 10 false FUL 4.969,2.094 6.76,2.333 1.792,0.24 10 false Multiplex Network Door ECU 4.677,0.646 4.958,0.875 0.281,0.229 10 false 11 2.99,0.656 3.146,0.854 0.156,0.198 10 false 4 2.99,1.354 3.146,1.552 0.156,0.198 10 false 1 2.583,0.656 3.042,0.854 0.458,0.198 10 false CTY 0.854,0.938 3,1.135 2.146,0.198 10 false Back Door Courtesy Switch 2.74,1.354 2.896,1.552 0.156,0.198 10 false E 0.406,1.833 0.865,2.031 0.458,0.198 10 false W14 0.396,2 3.917,2.198 3.521,0.198 10 false Back Door Lock with Courtesy Light Switch Assembly 1.792,3.125 2.406,3.323 0.615,0.198 10 false BCTY 2.281,3.01 2.438,3.208 0.156,0.198 10 false 4 2.99,3.01 3.302,3.208 0.313,0.198 10 false 34 2.333,3.521 2.646,3.719 0.313,0.198 10 false 4D 2.323,3.677 3.938,4.281 1.615,0.604 10 false Instrument Panel Junction Block Assembly 0.469,3.719 0.781,3.917 0.313,0.198 10 false MB 0.469,3.875 2.115,4.333 1.646,0.458 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:

If the multiplex network door ECU has been removed and installed or replaced, or if any of the connectors have been disconnected, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION


PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Courtesy SW Latch courtesy switch signal OFF or ON OFF: Back door closed
ON: Back door open
-
Body Electrical > Back Door > Data List
Tester Display
Courtesy SW
50003 159 4
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

2.INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY
2.INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)
a.

Disconnect the 4D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W14-4 (CTY) - W18-11 (FUL) Always Below 1 Ω
W14-1 (E) - Body ground Always Below 1 Ω
W14-4 (CTY) or W18-11 (FUL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR