Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM37A0E _59 Vehicle Exterior _086885 DOOR / HATCH _0418593 POWER BACK DOOR SYSTEM J

DOOR / HATCH  POWER BACK DOOR SYSTEM  Power Back Door does not Operate Using Outside Switch  


DESCRIPTION

The multiplex network door ECU detects the status of the power back door control switch.

If the power back door does not operate when the power back door control switch is operated, there may be a malfunction in the power back door control switch circuit.

WIRING DIAGRAM

B556244E10
4.271,1.969 4.729,2.167 0.458,0.198 10 false W18 1.323,1.479 1.781,1.677 0.458,0.198 10 false W17 1.24,0.969 1.396,1.167 0.156,0.198 10 false 2 3.198,0.948 3.354,1.146 0.156,0.198 10 false 5 4.333,0.958 4.563,1.177 0.229,0.219 10 false 8 4.531,0.948 5.146,1.146 0.615,0.198 10 false BDDN 1.323,1.635 3.26,2.094 1.938,0.458 10 false No. 1 Power Back Door Control Switch 5.146,1.083 5.76,1.281 0.615,0.198 10 false CPU 4.281,2.115 6.094,2.385 1.813,0.271 10 false Multiplex Network Door ECU 2.802,0.958 3.26,1.156 0.458,0.198 10 false CLS 1.448,0.969 1.604,1.167 0.156,0.198 10 false E

CAUTION / NOTICE / HINT

NOTICE:

If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION


PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
PBD Close SW No. 1 power back door control switch OFF or ON OFF: No. 1 power back door control switch not pressed
ON: No. 1 power back door control switch pressed
-
Body Electrical > Back Door > Data List
Tester Display
PBD Close SW
50003 159 8
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

2.INSPECT NO. 1 POWER BACK DOOR CONTROL SWITCH
2.INSPECT NO. 1 POWER BACK DOOR CONTROL SWITCH

OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 POWER BACK DOOR CONTROL SWITCH - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

NG

REPLACE NO. 1 POWER BACK DOOR CONTROL SWITCH

3.CHECK HARNESS AND CONNECTOR (NO. 1 POWER BACK DOOR CONTROL SWITCH - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)
a.

Disconnect the W18 multiplex network door ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W17-5 (CLS) - W18-8 (BDDN) Always Below 1 Ω
W17-2 (E) - Body ground Always Below 1 Ω
W17-5 (CLS) or W18-8 (BDDN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR