Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR
RM37A0E _59 Vehicle Exterior _086885 DOOR / HATCH _0418601 BACK DOOR N

DOOR / HATCH  BACK DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B563256C01
0.74,0.042 1.052,0.198 0.313,0.156 10 false *a 2.521,0.042 2.833,0.198 0.313,0.156 10 false *b
*a Centering Bolt
*b Standard Bolt


HINT:
·

Centering bolts are used to install the door hinges to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts (with washers) when making adjustments.

·

The specified torque for standard bolts is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 1.INSPECT BACK DOOR

a.

Check that the clearance measurements of areas a through i are within each standard range.

B563255N01
1.104,0.677 1.26,0.875 0.156,0.198 10 false a 1.844,1.083 2,1.281 0.156,0.198 10 false b 3.573,4.198 3.729,4.396 0.156,0.198 10 false c 2.771,4.104 2.927,4.302 0.156,0.198 10 false d 6.375,1.375 6.531,1.573 0.156,0.198 10 false e 5.854,1.188 6.01,1.385 0.156,0.198 10 false f 6.427,2.833 6.583,3.031 0.156,0.198 10 false g 5.813,2.813 5.969,3.01 0.156,0.198 10 false h 5.51,4.115 5.667,4.313 0.156,0.198 10 false i

Standard Clearance
Area Measurement Area Measurement
a 6.15 to 10.15 mm (0.242 to 0.400 in.) b -0.35 to 3.65 mm (-0.0138 to 0.144 in.)
c 4.05 to 9.05 mm (0.159 to 0.356 in.) d 0.95 to 5.95 mm (0.0374 to 0.234 in.)
e 2.9 to 7.9 mm (0.114 to 0.311 in.) f -1.0 to 4.0 mm (-0.0394 to 0.158 in.)
g 3.8 to 8.8 mm (0.150 to 0.346 in.) h 1.0 to 6.0 mm (0.0394 to 0.236 in.)
i 5.8 to 10.8 mm (0.228 to 0.425 in.) - -


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY

Hide 58409A 3.REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY (w/o Woofer)

Hide 64910J 4.REMOVE TONNEAU COVER ASSEMBLY

Hide 58441L 5.REMOVE BATTERY SERVICE HOLE COVER

Hide 64993 6.REMOVE REAR DECK FLOOR BOX

Hide 58387B 7.REMOVE REAR FLOOR FINISH PLATE

Hide 8.ADJUST BACK DOOR

a.
B563257

Loosen the 4 hinge bolts on the back door and adjust the back door position.


b.

Tighten the 4 hinge bolts on the back door after adjustment.

Torque:
46 N*m (469 kgf*cm, 34 ft.*lbf)


c.
B563258

Adjust the 2 back door upper stopper cushions to adjust the forward / rearward position of the back door.

NOTICE:
B530104C03
2.896,0.833 3.167,0.833 false 2.969,1.25 3.167,1.25 false 0.083,0.083 0.417,0.25 0.333,0.167 10 false *a 1.75,0.083 2.063,0.333 0.313,0.25 10 false *b 3.208,0.729 3.427,0.979 0.219,0.25 10 false *c 3.208,1.156 3.427,1.406 0.219,0.25 10 false *d
*a Correct
*b Incorrect
*c Rib of Back Door Upper Stopper Cushion
*d Clip of Back Door Upper Stopper Cushion


Make sure that the rib of the back door upper stopper cushion does not protrude from the clip of the back door upper stopper cushion.



d.
B563259

Using a T40 "TORX" socket wrench, slightly loosen the 2 striker mounting screws.


e.

Using a brass bar and a hammer, hit the striker to adjust its position.


f.

Using a T40 "TORX" socket wrench, tighten the 2 striker mounting screws after adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 58387B 9.INSTALL REAR FLOOR FINISH PLATE

Hide 64993 10.INSTALL REAR DECK FLOOR BOX

Hide 58441L 11.INSTALL BATTERY SERVICE HOLE COVER

Hide 64910J 12.INSTALL TONNEAU COVER ASSEMBLY

Hide 58409A 13.INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY (w/o Woofer)

Hide 58410B 14.INSTALL DECK BOARD ASSEMBLY