Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM37A0E _58 Vehicle Interior _086887 LIGHTING (INT) _0418630 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the following lights:

·

Map Light Assembly

·

Spot Light Assembly LH

·

Spot Light Assembly RH

·

No. 1 Room Light Assembly


WIRING DIAGRAM

E432341E01
1.26,0.875 3.073,1.125 1.813,0.25 10 false from Auxiliary Battery 1.719,1.521 2.635,1.719 0.917,0.198 10 false J/B 2.719,1.375 3.031,1.573 0.313,0.198 10 false 4F 2.76,1.167 2.917,1.365 0.156,0.198 10 false 1 2.708,2.323 3.021,2.521 0.313,0.198 10 false 4B 2.719,2.125 3.031,2.323 0.313,0.198 10 false 10 2.708,2.719 3.021,2.917 0.313,0.198 10 false 4B 2.719,2.531 3.031,2.729 0.313,0.198 10 false 29 3.219,1.521 3.833,1.719 0.615,0.198 10 false DOME 4.219,2 5.448,2.198 1.229,0.198 10 false DOME CUT 5.76,1.26 6.073,1.458 0.313,0.198 10 false 23 5.823,2.604 5.979,2.802 0.156,0.198 10 false 1 6.021,2.604 6.479,2.802 0.458,0.198 10 false ILE 6.01,1.26 6.625,1.458 0.615,0.198 10 false DOMR 3.042,3.135 6.063,3.396 3.021,0.26 10 false Instrument Panel Junction Block Assembly 4.281,4.927 4.896,5.125 0.615,0.198 10 false DOOR 4.385,5.719 4.844,5.917 0.458,0.198 10 false GND 4.76,5.729 5.073,5.927 0.313,0.198 10 false 11 4.76,4.927 4.917,5.125 0.156,0.198 10 false 3 3.458,6.406 4.073,6.604 0.615,0.198 10 false RLMP 3.448,6.635 3.792,6.865 0.344,0.229 10 false 15 2.802,6.115 3.26,6.313 0.458,0.198 10 false OFF 2.802,4.281 3.26,4.479 0.458,0.198 10 false OFF 2.823,4.885 3.135,5.083 0.313,0.198 10 false ON 2.781,5.719 3.094,5.917 0.313,0.198 10 false ON 1.667,4.865 2.896,5.063 1.229,0.198 10 false Map Light LH 1.625,6.208 2.854,6.406 1.229,0.198 10 false Map Light RH 0.875,4.573 1.333,4.771 0.458,0.198 10 false +B1 0.615,4.573 0.927,4.771 0.313,0.198 10 false 10 0.833,6.625 1.198,6.813 0.365,0.188 10 false R11 0.833,6.792 2.521,7.094 1.688,0.302 10 false Map Light Assembly 5.406,6.625 5.719,6.823 0.313,0.198 10 false MB 5.406,6.802 7.063,7.25 1.656,0.448 10 false Main Body ECU (Multiplex Network Body ECU) 0.219,7.177 0.375,7.375 0.156,0.198 10 false A 3.375,7.177 3.531,7.375 0.156,0.198 10 false B 3.938,4.594 4.396,4.792 0.458,0.198 10 false OFF 3.875,5.458 4.188,5.656 0.313,0.198 10 false ON 3.896,5.156 4.51,5.354 0.615,0.198 10 false DOOR

E432342E01
0.281,0.115 0.438,0.313 0.156,0.198 10 false A 3.438,0.115 3.594,0.313 0.156,0.198 10 false B 0.719,3.188 1.177,3.385 0.458,0.198 10 false R14 0.719,1.5 1.177,1.698 0.458,0.198 10 false R15 0.719,4.865 1.177,5.063 0.458,0.198 10 false R13 0.708,1.667 4.073,1.865 3.365,0.198 10 false Spot Light Assembly LH 0.708,3.354 4.073,3.552 3.365,0.198 10 false Spot Light Assembly RH 0.719,5.031 4.083,5.229 3.365,0.198 10 false No. 1 Room Light Assembly 0.771,0.844 0.927,1.042 0.156,0.198 10 false B 0.781,2.531 0.938,2.729 0.156,0.198 10 false B 0.771,4.198 0.927,4.396 0.156,0.198 10 false B 2.938,1.01 3.094,1.208 0.156,0.198 10 false E 2.927,2.677 3.083,2.875 0.156,0.198 10 false E 2.917,4.354 3.073,4.552 0.156,0.198 10 false E 2.781,0.677 3.24,0.875 0.458,0.198 10 false CTY 2.76,2.365 3.219,2.563 0.458,0.198 10 false CTY 2.771,4.042 3.229,4.24 0.458,0.198 10 false CTY 0.583,4.198 0.74,4.396 0.156,0.198 10 false 1 0.594,2.531 0.75,2.729 0.156,0.198 10 false 2 0.604,0.844 0.76,1.042 0.156,0.198 10 false 2 3.125,4.354 3.281,4.552 0.156,0.198 10 false 2 3.135,4.042 3.292,4.24 0.156,0.198 10 false 3 3.125,2.354 3.281,2.552 0.156,0.198 10 false 3 3.135,0.667 3.292,0.865 0.156,0.198 10 false 3 3.135,1 3.292,1.198 0.156,0.198 10 false 4 3.135,2.677 3.292,2.875 0.156,0.198 10 false 4 2.219,4.052 2.677,4.25 0.458,0.198 10 false DOOR 2.198,4.354 2.656,4.552 0.458,0.198 10 false ON 2.208,2.677 2.667,2.875 0.458,0.198 10 false ON 2.219,1.01 2.677,1.208 0.458,0.198 10 false ON 2.219,0.688 2.677,0.885 0.458,0.198 10 false OFF 2.219,2.365 2.677,2.563 0.458,0.198 10 false OFF

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




HINT:

The DOME CUT relay supplies power to the interior lights. If all the lights that use power from the DOME CUT relay do not turn on, check the interior light auto cut circuit first.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>Interior Light Auto Cut Circuit


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Illuminated Entry System Turns on the lights that are controlled by the illuminated entry system* OFF or ON Perform the Active Test with the door linked switch of the map light assembly on, switches of the spot light assembly LH and RH off and switch of the No. 1 room light assembly in the DOOR position.

*: Refer to System Description for the lights that are controlled by the illuminated entry system.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>SYSTEM DESCRIPTION


Body Electrical > Main Body > Active Test
Tester Display
Illuminated Entry System
50004 123 4
OK:

All lights that are controlled by the illuminated entry system come on.


Result:
Result Proceed to
OK A
NG (Map light assembly does not come on) B
NG (Spot light assembly LH does not come on) C
NG (Spot light assembly RH does not come on) D
NG (No. 1 room light assembly does not come on) E
NG (All lights that are controlled by the illuminated entry system do not come on) F




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT MAP LIGHT ASSEMBLY

C

GO TO PROBLEM SYMPTOMS TABLE (SPOT LIGHT ASSEMBLY LH)

D

GO TO PROBLEM SYMPTOMS TABLE (SPOT LIGHT ASSEMBLY RH)

E

GO TO PROBLEM SYMPTOMS TABLE (NO. 1 ROOM LIGHT ASSEMBLY)

F

4.INSPECT MAP LIGHT ASSEMBLY
2.INSPECT MAP LIGHT ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4B instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R11-10 (+B1) - 4B-10 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAP LIGHT ASSEMBLY

OK

5.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4B instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R11-10 (+B1) - 4B-10 Always Below 1 Ω
R11-3 (DOOR) - 4B-29 Always Below 1 Ω
R11-10 (+B1) or 4B-10 - Body ground Always 10 kΩ or higher
R11-3 (DOOR) or 4B-29 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E333581C75
1.333,0.365 1.625,0.583 0.292,0.219 4.76,0.5 5.083,0.729 0.323,0.229 3.302,1.125 3.531,1.479 false 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.396,0.396 1.854,0.625 0.458,0.229 10 false 4B 4.823,0.531 5.281,0.76 0.458,0.229 10 false MB 3.573,1.417 4.031,1.646 0.458,0.229 10 false ILE
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4B-29 - MB-1 (ILE) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY