Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM
RM37A0E _51 Engine / Hybrid System _086849 2GR-FKS ENGINE CONTROL _0418696 SFI SYSTEM C

2GR-FKS ENGINE CONTROL  SFI SYSTEM  P003012  HO2S Heater Control Bank 1 Sensor 1 Circuit Short to Battery  P003013  HO2S Heater Control Bank 1 Sensor 1 Circuit Open  P005012  HO2S Heater Control Bank 2 Sensor 1 Circuit Short to Battery  P005013  HO2S Heater Control Bank 2 Sensor 1 Circuit Open  P101A9E  A/F Sensor Heater Performance Bank 1 Sensor 1 Stuck On  P103A9E  A/F Sensor Heater Performance Bank 2 Sensor 1 Stuck On  


DESCRIPTION

The air fuel ratio sensor generates voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection duration. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.

The air fuel ratio sensor is a planar type and integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are a narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore sensor activation is accelerated.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: Value changes inside the ECM. Since the air fuel ratio sensor is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A306366E01
1.49,2.167 1,1.75 1,1.75 0.833,1.75 false 1.656,2.094 1.823,1.844 1.823,1.844 1.906,1.844 false 2.938,1.177 3.104,0.396 3.104,0.396 3.188,0.396 false 3.083,1.198 3.25,0.917 3.25,0.917 3.333,0.917 false 3.156,1.198 3.333,1.167 3.333,1.167 3.417,1.167 false 2.875,1.667 3.406,1.5 3.406,1.5 2.99,1.667 false 3.042,1.75 3.417,2.083 3.417,2.083 3.5,2.083 false 0.281,1.656 1.354,1.854 1.073,0.198 10 false Element 0.135,2.385 1.208,2.583 1.073,0.198 10 false Exhaust Gas 1.083,2.49 1.417,2.667 0.333,0.177 10 false A 1.802,2.49 2.135,2.667 0.333,0.177 10 false A 1.948,1.76 2.333,1.917 0.385,0.156 10 false Cover 3.26,0.219 4.417,0.583 1.156,0.365 10 false Solid Electrolyte (Zirconia Element) 3.385,0.833 4.052,0.99 0.667,0.156 10 false Alumina 3.458,1.083 4.125,1.24 0.667,0.156 10 false Heater 3.448,1.417 4.698,1.667 1.25,0.25 10 false Platinum Electrode 3.542,2 4.792,2.25 1.25,0.25 10 false Atmospheric Air 2.531,2.333 3.865,2.5 1.333,0.167 10 false A-A Cross Section 5.323,0.167 6.823,0.5 1.5,0.333 10 false ECM Monitored Air Fuel Ratio Sensor Voltage 5.563,2.25 6.896,2.417 1.333,0.167 10 false Air Fuel Ratio

HINT:
·

When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

·

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.

·

The ECM has a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.



A285791E36
0.104,0.052 3.313,0.292 3.208,0.24 10 false Reference (System Diagram of Bank 1 Sensor 1): 0.146,1.167 1.042,1.5 0.896,0.333 10 false from Battery 1.823,2.344 2.594,2.667 0.771,0.323 10 false A/F HTR 3.375,2.01 4.771,2.188 1.396,0.177 10 false Air Fuel Ratio Sensor 3.385,1.021 3.656,1.271 0.271,0.25 10 false +B 3.281,1.531 3.604,1.708 0.323,0.177 10 false A1A- 4.448,1.01 4.823,1.188 0.375,0.177 10 false HA1A 4.99,1 5.365,1.177 0.375,0.177 10 false HA1A 4.448,1.542 4.813,1.719 0.365,0.177 10 false A1A+ 5.01,1.521 5.375,1.698 0.365,0.177 10 false A1A+ 5.021,2.094 5.344,2.271 0.323,0.177 10 false A1A- 5.656,3.26 5.979,3.438 0.323,0.177 10 false ECM 6.177,1.615 6.76,1.958 0.583,0.344 10 false Duty Control 1.115,1.292 1.74,1.521 0.625,0.229 10 false A/F HTR 3.802,0.906 4.24,1.083 0.438,0.177 10 false Heater 3.771,1.385 4.229,1.563 0.458,0.177 10 false Sensor 0.042,2.063 0.99,2.427 0.948,0.365 10 false from EFI NO. 4 Fuse

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P003012 HO2S Heater Control Bank 1 Sensor 1 Circuit Short to Battery Air fuel ratio sensor heater current reaches the high limit (1 trip detection logic).
·

Short in air fuel ratio sensor (bank 1 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on DTC stored SAE Code: P0032
P003013 HO2S Heater Control Bank 1 Sensor 1 Circuit Open Air fuel ratio sensor heater current is less than 0.8 A, even when the air fuel ratio sensor heater duty cycle is 30% or higher (1 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on DTC stored SAE Code: P0031
P005012 HO2S Heater Control Bank 2 Sensor 1 Circuit Short to Battery Air fuel ratio sensor heater current reaches the high limit (1 trip detection logic).
·

Short in air fuel ratio sensor (bank 2 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on DTC stored SAE Code: P0052
P005013 HO2S Heater Control Bank 2 Sensor 1 Circuit Open Air fuel ratio sensor heater current is less than 0.8 A, even when the air fuel ratio sensor heater duty cycle is 30% or higher (1 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on DTC stored SAE Code: P0051
P101A9E A/F Sensor Heater Performance Bank 1 Sensor 1 Stuck On Air fuel ratio sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic).
·

Short in air fuel ratio sensor (bank 1 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on DTC stored SAE Code: P101D
P103A9E A/F Sensor Heater Performance Bank 2 Sensor 1 Stuck On Air fuel ratio sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic).
·

Short in air fuel ratio sensor (bank 2 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on DTC stored SAE Code: P103D

MONITOR DESCRIPTION

The ECM uses information from the air fuel ratio sensor to regulate the air fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the three-way catalytic converter to purify the exhaust gases.

The air fuel ratio sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum-coated zirconia and includes an integrated heating element.

The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.

The air fuel ratio sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor becomes inaccurate. As a result, the ECM is unable to regulate the air fuel ratio properly.

When the current in the air fuel ratio sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components Air fuel ratio sensor heater
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

P003012 and P005012
Heater output duty cycle Higher than 0%

P003013 and P005013
Heater output duty cycle 30% or higher

P101A9E and P103A9E
Heater output duty cycle Less than 60%

CONFIRMATION DRIVING PATTERN

A262623E87
0.792,0.969 1.583,1.26 0.792,0.292 10 false 3000 rpm 1.031,1.74 1.552,1.99 0.521,0.25 10 false Idling 0.25,2.042 1.458,2.479 1.208,0.438 10 false Ignition Switch ON 1.927,2.135 2.24,2.375 0.313,0.24 10 false [A] 2.76,1.625 3.146,1.938 0.385,0.313 10 false [B] 4.021,0.865 4.323,1.146 0.302,0.281 10 false [C] 5.385,1.604 5.594,2.135 0.208,0.531 10 false [D] 2.271,2.594 3.469,2.75 1.198,0.156 10 false 5 minutes or more 4.875,2.604 6.073,2.76 1.198,0.156 10 false 5 minutes or more 3.854,2.615 4.458,2.854 0.604,0.24 10 false 1 minute 5.979,3.031 6.177,3.229 0.198,0.198 10 false [E] 6.313,2.427 6.927,2.625 0.615,0.198 10 false Time 0.969,0.375 2.802,0.573 1.833,0.198 10 false Engine Speed

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON [A].

7.

Turn the GTS on.

8.

Start the engine and idle it for 5 minutes or more [B].

9.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

10.

Idle the engine for 5 minutes or more [D].

11.

Enter the following menus: Powertrain / Engine / Trouble Codes [E].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P003012, P003013, P005012, P005013, P101A9E or P103A9E.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [B] through [E] again.




WIRING DIAGRAM

A457142E01
0.896,5.594 1.969,5.792 1.073,0.198 10 false Battery 0.99,2.885 2.219,3.083 1.229,0.198 10 false EFI-MAIN 0.688,3.208 1.917,3.406 1.229,0.198 10 false EFI-MAIN 0.885,1.583 2.26,1.781 1.375,0.198 10 false EFI NO. 4 1.219,1.26 1.896,1.531 0.677,0.271 10 false A/F HTR 0.458,0.75 1.229,0.979 0.771,0.229 10 false A/F HTR 0.854,2.458 1.01,2.656 0.156,0.198 10 false 1 0.698,4.854 1.771,5.052 1.073,0.198 10 false FL MAIN 3.448,1.896 4.813,2.5 1.365,0.604 10 false Air Fuel Ratio Sensor (Bank 1 Sensor 1) 3.448,1.729 3.906,1.927 0.458,0.198 10 false C46 3.656,1.25 4.104,1.51 0.448,0.26 10 false A1A- 4.094,1.24 4.708,1.438 0.615,0.198 10 false A1A+ 3.667,0.51 3.979,0.708 0.313,0.198 10 false +B 4.063,0.51 4.677,0.708 0.615,0.198 10 false HA1A 3.5,0.51 3.656,0.708 0.156,0.198 10 false 2 3.5,1.26 3.656,1.458 0.156,0.198 10 false 4 4.51,1.25 4.667,1.448 0.156,0.198 10 false 3 4.5,0.51 4.656,0.708 0.156,0.198 10 false 1 3.646,2.969 3.958,3.167 0.313,0.198 10 false +B 4.052,2.969 4.667,3.167 0.615,0.198 10 false HA2A 4.073,3.719 4.688,3.917 0.615,0.198 10 false A2A+ 3.635,3.719 4.083,3.979 0.448,0.26 10 false A2A- 4.479,2.969 4.635,3.167 0.156,0.198 10 false 1 4.479,3.719 4.635,3.917 0.156,0.198 10 false 3 3.479,2.969 3.635,3.167 0.156,0.198 10 false 2 3.49,3.719 3.646,3.917 0.156,0.198 10 false 4 3.417,4.198 3.875,4.396 0.458,0.198 10 false C47 3.417,4.365 4.781,4.969 1.365,0.604 10 false Air Fuel Ratio Sensor (Bank 2 Sensor 1) 5.188,2.833 5.344,3.031 0.156,0.198 10 false * 5.167,5.438 5.323,5.635 0.156,0.198 10 false * 5.51,0.604 5.969,0.802 0.458,0.198 10 false C54 5.49,5.875 5.948,6.073 0.458,0.198 10 false A28 5.542,0.438 6,0.635 0.458,0.198 10 false 52 5.49,1.219 5.948,1.417 0.458,0.198 10 false 125 5.479,2.26 5.938,2.458 0.458,0.198 10 false 126 5.531,2.906 5.99,3.104 0.458,0.198 10 false 17 5.479,3.688 5.938,3.885 0.458,0.198 10 false 123 5.531,5.708 5.99,5.906 0.458,0.198 10 false 46 5.49,4.854 5.948,5.052 0.458,0.198 10 false 124 6.208,6.396 6.667,6.594 0.458,0.198 10 false ECM 5.844,5.771 6.458,5.969 0.615,0.198 10 false MREL 5.844,0.51 6.458,0.708 0.615,0.198 10 false HA1A 5.854,1.292 6.469,1.49 0.615,0.198 10 false A1A+ 5.854,2.354 6.469,2.552 0.615,0.198 10 false A1A- 5.844,2.99 6.458,3.188 0.615,0.198 10 false HA2A 5.854,3.771 6.469,3.969 0.615,0.198 10 false A2A+ 5.854,4.927 6.469,5.125 0.615,0.198 10 false A2A- 1.75,6.115 3.438,6.313 1.688,0.198 10 false *: Shielded 1.646,2.458 1.802,2.656 0.156,0.198 10 false 2 0.865,2.167 1.021,2.365 0.156,0.198 10 false 3 1.646,2.167 1.802,2.365 0.156,0.198 10 false 5 1.813,0.844 1.969,1.042 0.156,0.198 10 false 1 1.052,0.844 1.208,1.042 0.156,0.198 10 false 2 1.042,0.5 1.198,0.698 0.156,0.198 10 false 3 1.823,0.5 1.979,0.698 0.156,0.198 10 false 5 5.51,1.385 5.969,1.583 0.458,0.198 10 false C54 5.51,2.49 5.969,2.688 0.458,0.198 10 false C54 5.5,3.083 5.958,3.281 0.458,0.198 10 false C54 5.49,3.865 5.948,4.063 0.458,0.198 10 false C54 5.5,5.031 5.958,5.229 0.458,0.198 10 false C54

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Refer to "Data List / Active Test" [A/F (O2) Sensor Heater Duty Ratio B1S1 and A/F (O2) Sensor Heater Duty Ratio B2S1].

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the air fuel ratio sensor output voltage (Click here Engine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>P013613). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)
A456861C01
3.729,1.208 4.177,1.479 0.448,0.271 1.083,1.198 1.531,1.469 0.448,0.271 2.323,1.292 2.771,1 false 5.073,1.323 5.521,1.031 false 1.188,1.25 1.646,1.448 0.458,0.198 10 false C46 3.823,1.26 4.281,1.458 0.458,0.198 10 false C47 0.24,0.208 0.615,0.563 0.375,0.354 10 false *a 4.177,0.656 4.51,0.885 0.333,0.229 10 false *c 1.479,0.625 1.792,0.781 0.313,0.156 10 false *b 2.813,0.917 3.271,1.115 0.458,0.198 10 false +B 5.573,0.906 6.031,1.104 0.458,0.198 10 false +B
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor)
*b Bank 1
*c Bank 2 - -


a.

Disconnect the air fuel ratio sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C46-2 (+B) - Body ground Ignition switch ON 11 to 14 V
C47-2 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

6.INSPECT A/F HTR RELAY
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C46-1 (HA1A) - C54-52 (HA1A) Always Below 1 Ω
C47-1 (HA2A) - C54-17 (HA2A) Always Below 1 Ω
C46-1 (HA1A) or C54-52 (HA1A) - Body ground and other terminals Always 10 kΩ or higher
C47-1 (HA2A) or C54-17 (HA2A) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P003012, P003013, P005012, P005013, P101A9E OR P103A9E)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P003012, P003013, P005012, P005013, P101A9E OR P103A9E)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P003012, P003013, P005012, P005013, P101A9E or P103A9E is output B




A

B

6.INSPECT A/F HTR RELAY

OK

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF A/F HTR RELAY)

NG

REPLACE A/F HTR RELAY

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF A/F HTR RELAY)
A457143C01
0.094,0.125 0.406,0.323 0.313,0.198 10 false *1 0.354,1.104 0.667,1.302 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 A/F HTR Relay


a.

Remove the A/F HTR relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (A/F HTR relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (A/F HTR RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - A/F HTR RELAY)

8.CHECK HARNESS AND CONNECTOR (A/F HTR RELAY - BODY GROUND)
a.

Remove the A/F HTR relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (A/F HTR relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (A/F HTR RELAY - AIR FUEL RATIO SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (A/F HTR RELAY - AIR FUEL RATIO SENSOR)
a.

Remove the A/F HTR relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Disconnect the air fuel ratio sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (A/F HTR relay) - C46-2 (+B) Always Below 1 Ω
5 (A/F HTR relay) - C47-2 (+B) Always Below 1 Ω
5 (A/F HTR relay) or C46-2 (+B) - Body ground and other terminals Always 10 kΩ or higher
5 (A/F HTR relay) or C47-2 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN RELAY - A/F HTR RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR