Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for 8 Inch Display)
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0418790 NAVIGATION SYSTEM(for 8 Inch Display) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for 8 Inch Display)  B15C2  Speed Signal Malfunction  


DESCRIPTION

The navigation ECU receives a vehicle speed signal from the combination meter assembly and information from the navigation antenna assembly, and then adjusts the vehicle position on the map.

The navigation ECU stores this DTC when the difference between the speed information that the navigation antenna assembly receives and the SPD pulse received from the combination meter assembly becomes large.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective system based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



DTC No. Detection Item DTC Detection Condition Trouble Area
B15C2 Speed Signal Malfunction A difference between the GPS speed and SPD pulse is detected
·

Meter / gauge system

·

Navigation ECU

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

E368000E43
2.427,1.104 2.885,1.302 0.458,0.198 10 false 6 2.125,1.229 2.583,1.427 0.458,0.198 10 false +S 4.635,1.104 5.094,1.302 0.458,0.198 10 false 9 4.833,1.208 5.292,1.406 0.458,0.198 10 false SPD 4.854,2.042 5.313,2.24 0.458,0.198 10 false H18 4.854,2.188 5.958,2.479 1.104,0.292 10 false Navigation ECU 1.031,2.021 1.49,2.219 0.458,0.198 10 false H21 1.021,2.188 3.042,2.531 2.021,0.344 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 8 Inch Display)>PRECAUTION


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK VEHICLE SENSOR (OPERATION CHECK)
2.CHECK VEHICLE SENSOR (OPERATION CHECK)
a.
E276610

Enter the "System Sensors Check" screen. Refer to Check GPS & Vehicle Sensors in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 8 Inch Display)>OPERATION CHECK


b.

While driving the vehicle, compare the value of "Speed" to the reading on the speedometer. Check if these readings are almost equal.

HINT:

The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following procedure inspection referring to values in the Data List of the skid control ECU because it is the source of the vehicle speed signal.


OK:

Vehicle speed displayed on the "System Sensors Check" screen is almost the same as the actual vehicle speed measured using the GTS.

for HV Model: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>DATA LIST / ACTIVE TEST

for Gasoline Model: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

5.REPLACE NAVIGATION ECU

NG

3.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
3.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E393685C47
1.49,0.344 1.917,0.615 0.427,0.271 2.438,1.938 2.177,1.333 false 0.188,0.188 0.5,0.385 0.313,0.198 10 false *a 1.573,0.406 2.031,0.604 0.458,0.198 10 false H21 2.385,1.958 2.698,2.156 0.313,0.198 10 false +S 2.771,3.594 3.229,3.792 0.458,0.198 10 false GND 1.125,3.844 1.281,4.042 0.156,0.198 10 false A
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal H21-6 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal H21-6 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - COMBINATION METER ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - COMBINATION METER ASSEMBLY)
a.

Disconnect the H18 navigation ECU connector.


b.

Disconnect the H21 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H18-9 (SPD) - H21-6 (+S) Always Below 1 Ω
H18-9 (SPD) or H21-6 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE NAVIGATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE NAVIGATION ECU
a.

Replace the navigation ECU with a new or known good one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC
6.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (NAVIGATION ECU IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY