Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (COOLING) › COOLING FAN SYSTEM
RM37A0E _51 Engine / Hybrid System _086910 A25A-FXS, A25B-FXS COOLING _0419150 COOLING FAN SYSTEM J

A25A-FXS, A25B-FXS COOLING  COOLING FAN SYSTEM  Cooling Fan Circuit  


DESCRIPTION

The ECM calculates an appropriate cooling fan speed based on the engine coolant temperature, air conditioning switch status, refrigerant pressure, engine speed and vehicle speed, and sends a signal to the cooling fan ECU (fan with motor assembly). The cooling fan ECU (fan with motor assembly) steplessly control the speed of the cooling fan based on the duty cycle signal sent from the ECM. By sending signals to the cooling fan ECU (fan with motor assembly) in accordance with the driving conditions and by controlling the cooling fan speed optimally with the ECM, both high cooling performance and quietness are ensured.

WIRING DIAGRAM

A455910E01
0.792,5.792 1.865,5.99 1.073,0.198 10 false Battery 0.708,4.354 1.781,4.552 1.073,0.198 10 false FL MAIN 2.073,3.604 3.198,3.927 1.125,0.323 10 false EFI-MAIN NO. 1 0.708,1.969 1.781,2.167 1.073,0.198 10 false ALT 0.865,1.115 1.938,1.313 1.073,0.198 10 false FAN NO. 1 3.146,2.073 4.219,2.271 1.073,0.198 10 false FAN NO. 2 4.844,3.99 6.594,4.26 1.75,0.271 10 false Fan with Motor Assembly 4.958,0.948 5.417,1.146 0.458,0.198 10 false +B1 4.969,1.667 5.427,1.865 0.458,0.198 10 false IGS1 4.969,2.438 5.427,2.635 0.458,0.198 10 false SI 4.969,3.198 5.427,3.396 0.458,0.198 10 false E1 5.01,5.521 5.469,5.719 0.458,0.198 10 false RFC 5.01,6.302 5.469,6.5 0.458,0.198 10 false MREL 4.604,0.958 4.896,1.146 0.292,0.188 10 false A29 4.604,1.677 4.896,1.865 0.292,0.188 10 false A30 4.594,3.188 4.885,3.375 0.292,0.188 10 false A29 4.604,2.438 4.896,2.625 0.292,0.188 10 false A30 4.688,0.74 4.979,0.927 0.292,0.188 10 false 2 4.677,1.458 4.969,1.646 0.292,0.188 10 false 1 4.667,2.969 4.958,3.156 0.292,0.188 10 false 1 4.688,2.219 4.979,2.406 0.292,0.188 10 false 2 4.75,5.417 5.042,5.604 0.292,0.188 10 false 32 4.74,6.188 5.031,6.375 0.292,0.188 10 false 15 2.146,3.146 2.438,3.333 0.292,0.188 10 false 1 2.146,2.813 2.438,3 0.292,0.188 10 false 3 2.844,2.823 3.135,3.01 0.292,0.188 10 false 5 2.854,3.146 3.146,3.333 0.292,0.188 10 false 2 5.385,6.948 5.844,7.146 0.458,0.198 10 false ECM 5.042,6.948 5.5,7.271 0.458,0.323 10 false A27 0.708,3.115 1.833,3.438 1.125,0.323 10 false EFI-MAIN NO. 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Make sure to perform the necessary procedures (adjustment, calibration, initialization, or registration) after parts related to the cooling fan system have been removed/installed or replaced.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE ENGINE COOLING FAN DUTY RATIO)
a.

Check the operation of the cooling fan while operating it using the GTS.

Powertrain > Engine > Active Test
Tester Display
Control the Engine Cooling Fan Duty Ratio
50004 372 11
OK:
GTS Operation Fan Operation
30 - 100% Cooling fan operates
0% Cooling fan stops



Result:
Result Proceed to
OK A
Cooling fan does not operate B
Cooling fan does not stop C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.CHECK HARNESS AND CONNECTOR (FAN WITH MOTOR ASSEMBLY - ECM)

C

8.INSPECT ECM (RFC TERMINAL)
2.CHECK HARNESS AND CONNECTOR (FAN WITH MOTOR ASSEMBLY - ECM)
a.

Disconnect the A30 fan with motor assembly connector.


b.

Disconnect the A27 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A30-2 (SI) or A27-32 (RFC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (RFC TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN WITH MOTOR ASSEMBLY - ECM)

3.INSPECT ECM (RFC TERMINAL)
a.

Disconnect the A30 fan with motor assembly connector.


b.

Operate the cooling fan motor (fan with motor assembly) using the Active Test function and measure the resistance according to the value(s) in the table below.

Powertrain > Engine > Active Test
Tester Display
Control the Engine Cooling Fan Duty Ratio
50004 372 11
Standard Resistance:
Tester Connection GTS Operation Specified Condition
A30-2 (SI) - Body ground Before Active Test (0%) → During Active Test (100%) Before Active Test (0%): Resistance is stable → During Active Test (100%): Resistance fluctuates*


HINT:

*: Using the Active Test, duty control of the transistors in the ECM will be performed. Due to the duty control, resistance of the RFC terminal will be unstable during the Active Test. If the resistance is stable before the Active Test and fluctuates while performing the Active Test, it can be determined that the transistor is operating. If the transistor does not operate during the Active Test, the ECM may be malfunctioning.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FAN WITH MOTOR ASSEMBLY POWER SOURCE)

NG

4.CHECK HARNESS AND CONNECTOR (FAN WITH MOTOR ASSEMBLY POWER SOURCE)
a.

Disconnect the A29 fan with motor assembly connector.


A400098C20
0.094,0.917 0.479,1.146 0.385,0.229 0.906,1.917 1.125,1.917 1.125,1.917 1.385,1.229 true 2.583,1.938 2.375,1.938 2.375,1.938 2.063,1.24 true 0.052,0.042 0.281,0.271 0.229,0.229 10 false *a 2.635,1.854 2.938,2.031 0.302,0.177 10 false +B1 0.698,1.854 0.906,2.031 0.208,0.177 10 false E1 0.156,0.958 0.469,1.135 0.313,0.177 10 false A29
*a Front view of wire harness connector
(to Fan with Motor Assembly)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A29-2 (+B1) - A29-1 (E1) Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (FAN WITH MOTOR ASSEMBLY POWER SOURCE)

NG

7.CHECK HARNESS AND CONNECTOR (FAN WITH MOTOR ASSEMBLY - BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (FAN WITH MOTOR ASSEMBLY POWER SOURCE)
a.

Disconnect the A30 fan with motor assembly connector.


b.

Turn the ignition switch to ON.


c.
A404935C25
0.708,1.073 1.073,1.313 0.365,0.24 1.156,1.844 1.625,1.292 true 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 0.781,1.125 1.167,1.385 0.385,0.26 10 false A30 1.031,1.865 1.625,2.063 0.594,0.198 10 false IGS1
*a Front view of wire harness connector
(to Fan with Motor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A30-1 (IGS1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

6.CHECK HARNESS AND CONNECTOR (FAN WITH MOTOR ASSEMBLY - EFI-MAIN NO. 1 RELAY)
6.CHECK HARNESS AND CONNECTOR (FAN WITH MOTOR ASSEMBLY - EFI-MAIN NO. 1 RELAY)
a.

Disconnect the A30 fan with motor assembly connector.


b.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A30-1 (IGS1) - 5 (EFI-MAIN NO. 1 relay) Always Below 1 Ω



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN WITH MOTOR ASSEMBLY - EFI-MAIN NO. 1 RELAY)

7.CHECK HARNESS AND CONNECTOR (FAN WITH MOTOR ASSEMBLY - BODY GROUND)
a.

Disconnect the A29 fan with motor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-1 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN WITH MOTOR ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN WITH MOTOR ASSEMBLY - BODY GROUND)

8.INSPECT ECM (RFC TERMINAL)
a.

Disconnect the A30 fan with motor assembly connector.


b.

Operate the cooling fan motor (fan with motor assembly) using the Active Test function and measure the resistance according to the value(s) in the table below.

Powertrain > Engine > Active Test
Tester Display
Control the Engine Cooling Fan Duty Ratio
50004 372 11
Standard Resistance:
Tester Connection GTS Operation Specified Condition
A30-2 (SI) - Body ground Before Active Test (0%) → During Active Test (100%) Before Active Test (0%): Resistance is stable → During Active Test (100%): Resistance fluctuates*


HINT:

*: Using the Active Test, duty control of the transistors in the ECM will be performed. Due to the duty control, resistance of the RFC terminal will be unstable during the Active Test. If the resistance is stable before the Active Test and fluctuates while performing the Active Test, it can be determined that the transistor is operating. If the transistor does not operate during the Active Test, the ECM may be malfunctioning.



Result:
Proceed to
OK
NG



OK

NG

9.CHECK HARNESS AND CONNECTOR (FAN WITH MOTOR ASSEMBLY - ECM)
9.CHECK HARNESS AND CONNECTOR (FAN WITH MOTOR ASSEMBLY - ECM)
a.

Disconnect the A30 fan with motor assembly connector.


b.

Disconnect the A27 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A30-2 (SI) - A27-32 (RFC) Always Below 1 Ω



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN WITH MOTOR ASSEMBLY - ECM)