The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during radiator assembly removal/installation are shown below.
53852B
1.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH
53851D
2.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH
51441
3.REMOVE NO. 1 ENGINE UNDER COVER
51420
4.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY
5.DRAIN ENGINE COOLANT (for Engine)
6.REMOVE HEADLIGHT ASSEMBLY
52611
7.REMOVE FRONT BUMPER ENERGY ABSORBER
52021
8.REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY
88790B
9.REMOVE THERMISTOR ASSEMBLY
53510
10.REMOVE HOOD LOCK ASSEMBLY
17750A
11.REMOVE INLET AIR CLEANER ASSEMBLY
16595B
12.REMOVE NO. 1 RADIATOR AIR GUIDE LH
Remove the clip and disengage the claw.
Disengage the guide to remove the No. 1 radiator air guide LH.
16593B
13.REMOVE NO. 1 RADIATOR AIR GUIDE RH
Remove the clip and disengage the claw.
Disengage the guide to remove the No. 1 radiator air guide RH.
53205
14.REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY
Disconnect the 2 horn connectors and vehicle approaching speaker assembly connector.
Remove the bolt to separate the inlet hose.
Disengage the clamp to disconnect the hood lock control cable assembly from the upper radiator support sub-assembly.
Disengage the 3 claws.
Remove the 5 bolts and upper radiator support sub-assembly.
16594A
15.REMOVE NO. 2 RADIATOR AIR GUIDE
Remove the hood lock control cable assembly from the No. 2 radiator air guide.
Remove the No. 2 radiator air guide.
16281N
16.DISCONNECT NO. 4 WATER BY-PASS HOSE
Slide the clip and disconnect the No. 4 water by-pass hose from the radiator assembly.
16283D
17.DISCONNECT NO. 6 WATER BY-PASS HOSE
Disconnect the No. 6 water by-pass hose from the radiator assembly.
16571C
18.DISCONNECT NO. 1 RADIATOR HOSE
Disengage the clamp to disconnect the No. 1 radiator hose from the fan with motor assembly.
Slide the clip and disconnect the No. 1 radiator hose from the radiator assembly.
16572D
19.DISCONNECT NO. 2 RADIATOR HOSE
Disengage the clamp to disconnect the No. 2 radiator hose from the fan with motor assembly.
Slide the clip and disconnect the No. 2 radiator hose from the radiator assembly.
G9228A
20.DISCONNECT NO. 4 INVERTER COOLING HOSE
Disengage the clamp to disconnect the No. 4 inverter cooling hose from the fan with motor assembly.
G9229A
21.DISCONNECT NO. 5 INVERTER COOLING HOSE
Disengage the 3 clamps to disconnect the No. 5 inverter cooling hose from the fan with motor assembly.
16400
22.REMOVE RADIATOR ASSEMBLY
Disconnect the cooling fan motor connector.
Disengage the clamp to disconnect the wire harness from the fan with motor assembly.
Rotate the lever while pushing the lock, and disconnect the cooling fan motor connector.
After disconnecting the cooling fan motor connector, make sure that dirt, water or other foreign matter does not contact the connecting parts of the cooling fan motor connector.
Disengage the 2 clamps to disconnect the wire harness from the fan with motor assembly.
Disengage the 2 claws.
Disengage the 2 guides to separate the cooler condenser assembly from the radiator assembly.
Make sure not to damage the cooler condenser assembly when separating the cooler condenser assembly.
Remove the radiator assembly with the fan with motor assembly from the vehicle body.
Do not apply excessive force to the cooler condenser assembly or pipe when removing the radiator assembly with the fan with motor assembly.
Disengage the 2 claws.
Disengage the 2 guides to remove the fan with motor assembly from the radiator assembly.
Do not damage the radiator assembly when removing the fan with motor assembly.
16523A
23.REMOVE RADIATOR SUPPORT CUSHION
Remove the 2 radiator support cushions from the radiator assembly.
16535
24.REMOVE LOWER RADIATOR SUPPORT
Remove the 2 lower radiator supports from the radiator assembly.