Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0419517 REAR VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  Image from Camera for Rear View Monitor is Abnormal  


DESCRIPTION

The video signal of the rear television camera assembly is transmitted to the radio and display receiver assembly.

WIRING DIAGRAM

E432751E02
5.292,2.271 5.833,2.573 0.542,0.302 10 false W16 5.292,2.427 6.76,2.896 1.469,0.469 10 false Rear Television Camera Assembly 5.5,0.635 5.927,0.865 0.427,0.229 10 false CB+ 5.5,1.031 5.938,1.333 0.438,0.302 10 false CV+ 5.5,1.427 5.865,1.708 0.365,0.281 10 false CV- 5.5,1.823 5.99,2.01 0.49,0.188 10 false CGND 1.479,0.625 1.938,0.885 0.458,0.26 10 false CA+ 1.573,1.021 1.896,1.26 0.323,0.24 10 false V+ 1.594,1.406 1.917,1.698 0.323,0.292 10 false V- 1.365,1.802 1.938,2.125 0.573,0.323 10 false CGND 0.104,2.625 0.5,2.813 0.396,0.188 10 false H2 5.302,0.542 5.531,0.844 0.229,0.302 10 false 6 5.302,0.927 5.542,1.25 0.24,0.323 10 false 3 5.302,1.323 5.49,1.615 0.188,0.292 10 false 2 5.302,1.698 5.458,1.917 0.156,0.219 10 false 5 4.042,1.979 4.188,2.135 0.146,0.156 10 false * 3.896,3.323 4.708,3.521 0.813,0.198 10 false *: Shielded 1.854,0.531 2.344,0.875 0.49,0.344 10 false 30 1.854,0.927 2.24,1.156 0.385,0.229 10 false 28 1.865,1.323 2.24,1.583 0.375,0.26 10 false 29 1.865,1.698 2.292,1.938 0.427,0.24 10 false 27 0.094,2.792 2.583,3.021 2.49,0.229 10 false Radio and Display Receiver Assembly 1.875,2.073 2.302,2.313 0.427,0.24 10 false 26 1.396,2.177 1.969,2.5 0.573,0.323 10 false CSLD

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the H2 radio and display receiver assembly connector.


b.

Disconnect the W16 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-30 (CA+) - W16-6 (CB+) Always Below 1 Ω
H2-28 (V+) - W16-3 (CV+) Always Below 1 Ω
H2-29 (V-) - W16-2 (CV-) Always Below 1 Ω
H2-27 (CGND) - W16-5 (CGND) Always Below 1 Ω
H2-26 (CSLD) - Body ground Always Below 1 Ω
H2-30 (CA+) or W16-6 (CB+) - Body ground Always 10 kΩ or higher
H2-28 (V+) or W16-3 (CV+) - Body ground Always 10 kΩ or higher
H2-29 (V-) or W16-2 (CV-) - Body ground Always 10 kΩ or higher
H2-27 (CGND) or W16-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the H2 radio and display receiver assembly connector.


b.
E366062C62
1.5,0.25 1.917,0.5 0.417,0.25 1.438,1.375 1.99,1.917 1.99,1.917 2.156,1.917 false 1.167,1.375 1.167,1.958 1.167,1.958 1,1.958 false 1.063,1.344 0.75,1.146 0.75,1.146 0.594,1.146 false 1.625,0.292 1.938,0.49 0.313,0.198 10 false H2 0.125,0.063 0.438,0.26 0.313,0.198 10 false *a 2.229,1.833 2.813,2.073 0.583,0.24 10 false CGND 0.771,1.865 1.125,2.083 0.354,0.219 10 false V- 0.281,1.063 0.635,1.281 0.354,0.219 10 false CA+
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-29 (V-) - Body ground Always Below 1 Ω
H2-27 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H2-30 (CA+) - H2-27 (CGND) Ignition switch ACC 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

3.INSPECT REAR TELEVISION CAMERA ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

3.INSPECT REAR TELEVISION CAMERA ASSEMBLY
a.

Reconnect the W16 rear television camera assembly connector.


b.
E366062C66
1.458,0.198 1.948,0.479 0.49,0.281 1.271,1.906 1.271,1.375 true 0.854,1.875 1.177,1.365 true 1.604,0.281 2.042,0.563 0.438,0.281 10 false H2 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a 1.208,1.927 1.667,2.125 0.458,0.198 10 false V+ 0.74,1.885 1.052,2.083 0.313,0.198 10 false V-
*a Component with harness connected
(Radio and Display Receiver Assembly)


E265840C01
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Using an oscilloscope, check the waveform of the rear television camera assembly.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


OK:

Waveform is similar to that shown in the illustration.


Item Content
Measurement terminal H2-28 (V+) - H2-29 (V-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Ignition switch ON, reverse (R) selected

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the ignition switch is turned to ACC.

·

Make sure that the rear camera is enabled in general settings.




Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG