Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › 2020.02–2020.11
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0419518 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1622  Open or Short Circuit in Back Camera Signal  


DESCRIPTION

DTC C1622 is stored if the parking assist ECU judges as a result of its self check that the signals or signal lines between the parking assist ECU and the rear television camera assembly are not normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1622 Open or Short Circuit in Back Camera Signal Open or short in the rear television camera signal circuit
·

Harness or connector

·

Rear television camera assembly

·

Parking assist ECU



WIRING DIAGRAM

E379402E27
5.5,3.094 7.031,3.469 1.531,0.375 10 false Parking Assist ECU 5.5,2.906 5.958,3.104 0.458,0.198 10 false H19 5.552,0.615 6.01,0.813 0.458,0.198 10 false CB+ 5.552,1.115 6.01,1.313 0.458,0.198 10 false CV+ 5.573,1.604 6.031,1.802 0.458,0.198 10 false CV- 5.24,0.51 5.677,0.708 0.438,0.198 10 false 33 5.24,0.969 5.677,1.167 0.438,0.198 10 false 29 5.229,1.479 5.667,1.677 0.438,0.198 10 false 30 5.563,2.052 6.198,2.26 0.635,0.208 10 false CGND 5.24,1.938 5.677,2.135 0.438,0.198 10 false 32 5.25,2.302 5.688,2.5 0.438,0.198 10 false 31 5.563,2.427 6.198,2.635 0.635,0.208 10 false SGND 0.375,2.896 0.833,3.094 0.458,0.198 10 false W15 0.375,3.073 2.833,3.333 2.458,0.26 10 false Rear Television Camera Assembly 1.292,0.646 1.75,0.844 0.458,0.198 10 false CB+ 1.281,1.115 1.74,1.313 0.458,0.198 10 false CV+ 1.292,1.594 1.75,1.792 0.458,0.198 10 false CV- 1.177,2.052 1.813,2.26 0.635,0.208 10 false CGND 1.75,0.521 2.188,0.719 0.438,0.198 10 false 6 1.719,1.01 2.156,1.208 0.438,0.198 10 false 3 1.74,1.469 2.177,1.667 0.438,0.198 10 false 2 1.75,1.938 2.188,2.135 0.438,0.198 10 false 5 3.51,2.365 3.667,2.563 0.156,0.198 10 false * 0.333,3.417 1.854,3.677 1.521,0.26 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the H19 parking assist ECU connector.


b.

Disconnect the W15 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H19-33 (CB+) - W15-6 (CB+) Always Below 1 Ω
H19-29 (CV+) - W15-3 (CV+) Always Below 1 Ω
H19-30 (CV-) - W15-2 (CV-) Always Below 1 Ω
H19-32 (CGND) - W15-5 (CGND) Always Below 1 Ω
H19-33 (CB+) or W15-6 (CB+) - Body ground Always 10 kΩ or higher
H19-29 (CV+) or W15-3 (CV+) - Body ground Always 10 kΩ or higher
H19-30 (CV-) or W15-2 (CV-) - Body ground Always 10 kΩ or higher
H19-32 (CGND) or W15-5 (CGND) - Body ground Always 10 kΩ or higher
H19-31 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK PARKING ASSIST ECU (CV-, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (CV-, CGND)
a.

Disconnect the H19 parking assist ECU connector.


b.
E330226C47
1.969,1.771 1.74,1.771 1.74,1.771 1.646,1.125 true 1.188,1.792 1.354,1.792 1.354,1.792 1.5,1.146 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 0.719,1.729 1.219,1.885 0.5,0.156 10 false CGND 2.146,1.708 2.646,1.865 0.5,0.156 10 false CV-
*a Component without harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
30 (CV-) - Body ground Always Below 1 Ω
32 (CGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK PARKING ASSIST ECU (CB+, CGND)

NG

3.CHECK PARKING ASSIST ECU (CB+, CGND)
a.
E407111C19
1.417,0.25 1.917,0.5 0.5,0.25 1.438,1.146 1.208,1.906 1.208,1.906 0.958,1.906 true 1.51,1.156 1.979,1.948 1.979,1.948 2.229,1.948 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 0.646,1.823 1.115,2.021 0.469,0.198 10 false CB+ 1.542,0.292 2.042,0.448 0.5,0.156 10 false H19 2.271,1.865 2.833,2.052 0.563,0.188 10 false CGND
*a Component with harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H19-32 (CGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H19-33 (CB+) - H19-32 (CGND) Ignition switch ON 5.5 to 7.05 V
H19-33 (CB+) - H19-32 (CGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK REAR TELEVISION CAMERA ASSEMBLY (CV+, CGND)

NG

4.CHECK REAR TELEVISION CAMERA ASSEMBLY (CV+, CGND)
a.

Remove the parking assist ECU with the connector still connected.


b.

Using an oscilloscope, check the waveform of the rear television camera assembly.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


E430500C09
0.75,0.292 1.25,0.542 0.5,0.25 1.667,2.083 1.5,2.083 1.5,2.083 1.052,1.104 true 4.302,2.052 4.104,1.552 true 6.333,2.052 6.083,1.406 true 5.802,2.031 5.969,1.458 true 3.813,2.031 3.969,1.594 true 0.583,2.063 0.75,2.063 0.75,2.063 0.875,1.094 true 1.729,2 2.083,2.198 0.354,0.198 10 false CV+ 0.104,1.99 0.583,2.167 0.479,0.177 10 false CGND 3.365,1.188 3.844,1.365 0.479,0.177 10 false GND 5.271,1.188 5.75,1.365 0.479,0.177 10 false GND 0.083,0.063 0.563,0.24 0.479,0.177 10 false *a 3.677,0.208 4.156,0.385 0.479,0.177 10 false *b 5.604,0.219 6.083,0.396 0.479,0.177 10 false *c 6.302,2.094 6.781,2.271 0.479,0.177 10 false *e 4.271,2.083 4.75,2.26 0.479,0.177 10 false *e 5.688,2.094 6.167,2.271 0.479,0.177 10 false *d 3.74,2.083 4.219,2.26 0.479,0.177 10 false *d 0.865,0.333 1.344,0.51 0.479,0.177 10 false H19
*a Component with harness connected
(Parking Assist ECU)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the ignition switch is turned to ACC.



Measurement Condition
Item Content
Terminal No. (Symbol) H19-29 (CV+) - H19-32 (CGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, panoramic view monitor system operating

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG