Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › 2020.02–2020.11
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0419518 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1683  Side Camera Feedback Malfunction  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the passenger side television camera assembly to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1683 Side Camera Feedback Malfunction Side camera feedback malfunction
·

Harness or connector

·

Parking assist ECU

·

Side television camera assembly RH

·

Outer rear view mirror assembly RH



WIRING DIAGRAM

E469404E06
5.708,2.813 6.167,3.01 0.458,0.198 10 false H19 5.708,2.979 7.031,3.385 1.323,0.406 10 false Parking Assist ECU 0.938,3.042 3.573,3.406 2.635,0.365 10 false Outer Rear View Mirror Assembly RH 0.74,2.375 3.156,2.625 2.417,0.25 10 false Side Television Camera Assembly RH 0.948,2.875 1.406,3.073 0.458,0.198 10 false J13 6.021,2.344 6.719,2.583 0.698,0.24 10 false SGND 6.021,1.927 6.719,2.167 0.698,0.24 10 false RGND 6.021,1.49 6.719,1.729 0.698,0.24 10 false RCV- 6,1.104 6.698,1.344 0.698,0.24 10 false RCV+ 6,0.656 6.698,0.896 0.698,0.24 10 false RCB+ 3.396,0.573 4.094,0.813 0.698,0.24 10 false RCB+ 3.385,0.958 4.083,1.198 0.698,0.24 10 false RCV+ 3.396,1.375 4.094,1.615 0.698,0.24 10 false RCV- 3.385,1.823 4.083,2.063 0.698,0.24 10 false RGND 5.698,0.594 6.01,0.792 0.313,0.198 10 false 40 5.688,1 6,1.198 0.313,0.198 10 false 38 5.688,1.396 6,1.594 0.313,0.198 10 false 16 5.698,1.833 6.01,2.031 0.313,0.198 10 false 17 5.708,2.24 6.021,2.438 0.313,0.198 10 false 39 3.906,1.802 4.219,2 0.313,0.198 10 false 2 3.885,1.375 4.198,1.573 0.313,0.198 10 false 4 3.917,0.958 4.229,1.156 0.313,0.198 10 false 5 3.906,0.583 4.219,0.781 0.313,0.198 10 false 3 4.781,2.302 4.938,2.5 0.156,0.198 10 false * 0.417,3.458 1.448,3.771 1.031,0.313 10 false *: Shielded 1.219,0.698 1.917,0.938 0.698,0.24 10 false CB+ 1.208,1.125 1.906,1.365 0.698,0.24 10 false CV+ 1.208,1.51 1.906,1.75 0.698,0.24 10 false CV- 1.188,1.938 1.885,2.177 0.698,0.24 10 false GND 0.75,2.208 1.021,2.438 0.271,0.229 10 false B 1.708,0.594 2.021,0.792 0.313,0.198 10 false 1 1.708,1.792 2.021,1.99 0.313,0.198 10 false 5 1.708,1.365 2.021,1.563 0.313,0.198 10 false 7 1.698,0.958 2.01,1.156 0.313,0.198 10 false 3 3.875,2.208 4.188,2.406 0.313,0.198 10 false 1 3.375,2.333 4.073,2.573 0.698,0.24 10 false SGND

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1683 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)
2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)
a.

Disconnect the H19 parking assist ECU connector.


b.

Disconnect the J13 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H19-40 (RCB+) - J13-3 (RCB+) Always Below 1 Ω
H19-38 (RCV+) - J13-5 (RCV+) Always Below 1 Ω
H19-16 (RCV-) - J13-4 (RCV-) Always Below 1 Ω
H19-17 (RGND) - J13-2 (RGND) Always Below 1 Ω
H19-39 (SGND) - J13-1 (SGND) Always Below 1 Ω
H19-40 (RCB+) or J13-3 (RCB+) - Body ground Always 10 kΩ or higher
H19-38 (RCV+) or J13-5 (RCV+) - Body ground Always 10 kΩ or higher
H19-16 (RCV-) or J13-4 (RCV-) - Body ground Always 10 kΩ or higher
H19-17 (RGND) or J13-2 (RGND) - Body ground Always 10 kΩ or higher
H19-39 (SGND) or J13-1 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK PARKING ASSIST ECU (RCV-, RGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK PARKING ASSIST ECU (RCV-, RGND)
a.

Disconnect the H19 parking assist ECU connector.


b.
E330226C50
1.385,1.781 1.219,1.781 1.219,1.781 1.01,1.031 true 1.083,0.333 1,0.333 1,0.333 0.938,1 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.167,0.26 1.667,0.417 0.5,0.156 10 false RGND 1.469,1.75 1.969,1.906 0.5,0.156 10 false RCV-
*a Component without harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
17 (RGND) - Body ground Always Below 1 Ω
16 (RCV-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK PARKING ASSIST ECU (RCB+, RGND)

NG

4.CHECK PARKING ASSIST ECU (RCB+, RGND)
a.
E402272C20
1.417,0.25 1.917,0.5 0.5,0.25 0.5,1.771 0.677,1.771 0.677,1.771 0.865,1.156 true 0.667,0.333 0.833,0.333 0.833,0.333 0.938,0.99 true 0.083,0.042 0.5,0.302 0.417,0.26 10 false *a 0.198,0.25 0.76,0.448 0.563,0.198 10 false RGND 0.104,1.688 0.667,1.844 0.563,0.156 10 false RCB+ 1.521,0.281 2.021,0.438 0.5,0.156 10 false H19
*a Component with harness connected
(Parking Assist ECU)


Remove the parking assist ECU with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H19-17 (RGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H19-40 (RCB+) - H19-17 (RGND) Ignition switch ON 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

5.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH (RCV+, RGND)

NG

5.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH (RCV+, RGND)
a.

Remove the parking assist ECU with the connector still connected.


b.

Using an oscilloscope, check the waveform of the side television camera assembly RH.

HINT:

A waterproof connector is used for the side television camera assembly RH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


E430500C12
0.75,0.292 1.25,0.542 0.5,0.25 0.333,2.167 0.167,2.167 0.167,2.167 0.406,1 true 4.302,2.052 4.104,1.552 true 6.333,2.052 6.083,1.406 true 5.802,2.031 5.969,1.458 true 3.813,2.031 3.969,1.594 true 1.833,1.833 1.667,1.833 1.667,1.833 0.458,1.104 true 1.917,1.76 2.385,2 0.469,0.24 10 false RCV+ 0.417,2.083 0.896,2.26 0.479,0.177 10 false RGND 3.365,1.156 3.844,1.333 0.479,0.177 10 false GND 5.26,1.167 5.74,1.344 0.479,0.177 10 false GND 0.083,0.063 0.563,0.24 0.479,0.177 10 false *a 3.469,0.083 3.948,0.26 0.479,0.177 10 false *b 5.417,0.073 5.896,0.25 0.479,0.177 10 false *c 6.302,2.094 6.781,2.271 0.479,0.177 10 false *e 4.271,2.083 4.75,2.26 0.479,0.177 10 false *e 5.688,2.094 6.167,2.271 0.479,0.177 10 false *d 3.74,2.083 4.219,2.26 0.479,0.177 10 false *d 0.854,0.344 1.333,0.521 0.479,0.177 10 false H19
*a Component with harness connected
(Parking Assist ECU)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


HINT:
·

The video waveform changes according to the image sent by the side television camera assembly RH.

·

The video waveform is constantly output when the ignition switch is turned to ACC.



Measurement Condition
Item Content
Tester Connection H19-38 (RCV+) - H19-17 (RGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, panoramic view monitor system operating

OK:

Waveform is similar to that shown in illustration.



Result:
Proceed to
OK
NG



OK

NG

6.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
6.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.
E461714C15
0.646,0.833 1.146,1.083 0.5,0.25 0.323,2.281 0.823,2.531 0.5,0.25 0.99,0.375 1.24,0.375 1.24,0.375 1.427,0.76 true 2.406,0.365 2.156,0.365 2.156,0.365 1.979,0.75 true 1,1.427 1.25,1.427 1.25,1.427 1.427,1.104 true 2.438,1.427 2.188,1.427 2.188,1.427 2.01,1.073 true 1.188,1.813 1.438,1.813 1.438,1.813 1.406,2.5 true 2.292,1.781 2.042,1.781 2.042,1.781 1.719,2.521 true 2.271,3.167 2.021,3.167 2.021,3.167 1.906,2.688 true 1.24,3.156 1.479,3.156 1.479,3.156 1.552,2.698 true 0.792,1.719 1.406,1.917 0.615,0.198 10 false RCV+ 2.458,0.292 3.073,0.49 0.615,0.198 10 false CB+ 0.688,0.281 1.302,0.479 0.615,0.198 10 false CV+ 0.604,1.333 1.219,1.531 0.615,0.198 10 false CV- 2.479,1.354 3.094,1.552 0.615,0.198 10 false GND 2.396,1.698 3.01,1.896 0.615,0.198 10 false RCB+ 2.313,3.083 2.927,3.281 0.615,0.198 10 false RGND 0.865,3.063 1.479,3.26 0.615,0.198 10 false RCV- 0.833,0.875 1.448,1.073 0.615,0.198 10 false B 0.458,2.323 1.073,2.521 0.615,0.198 10 false J13 0.052,0.052 0.667,0.25 0.615,0.198 10 false *a 0.063,1.625 0.677,1.823 0.615,0.198 10 false *b
*a Front view of wire harness connector
(to Side Television Camera Bssembly RH)
*b Front view of wire harness connector
(to Outer Rear View Mirror Bssembly RH)


Disconnect the side television camera assembly RH connector.


b.

Disconnect the outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 (CB+) - J13-3 (RCB+) Blways Below 1 Ω
B-3 (CV+) - J13-5 (RCV+) Blways Below 1 Ω
B-7 (CV-) - J13-4 (RCV-) Blways Below 1 Ω
B-5 (GND) - J13-2 (RGND) Blways Below 1 Ω
B-1 (CB+) or J13-3 (RCB+) - Body ground Blways 10 kΩ or higher
B-3 (CV+) or J13-5 (RCV+) - Body ground Blways 10 kΩ or higher
B-7 (CV-) or J13-4 (RCV-) - Body ground Blways 10 kΩ or higher
B-5 (GND) or J13-2 (RGND) - Body ground Blways 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

7.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH
a.

Replace the side television camera assembly RH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1683 is not output.



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY RH WAS DEFECTIVE)

NG