Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for ERA-GLONASS)
RM37A0E _56 Audio / Visual / Telematics _086879 TELEMATICS _0419698 TELEMATICS SYSTEM(for ERA-GLONASS) C

TELEMATICS  TELEMATICS SYSTEM(for ERA-GLONASS)  B1572  Microphone Error  


DESCRIPTION

This DTC is stored when a communication telematics box signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1572 Microphone Error Current at terminal MCVD exceeds the malfunction threshold for 10 seconds or more while the ignition switch is ON
·

Telematics transceiver

·

Map light assembly

·

Communication telematics box

·

Harness or connector



WIRING DIAGRAM

E438040E03
1.5,1.406 2.115,1.604 0.615,0.198 10 false MCMD 1.646,1.792 2.26,1.99 0.615,0.198 10 false SP+ 1.667,2.167 2.281,2.365 0.615,0.198 10 false SP- 1.573,2.594 2.188,2.792 0.615,0.198 10 false MICV 1.521,2.99 2.135,3.188 0.615,0.198 10 false MIC1+ 1.51,3.385 2.125,3.583 0.615,0.198 10 false MIC2+ 1.615,3.76 2.229,3.958 0.615,0.198 10 false MCI- 5.802,1.396 6.417,1.594 0.615,0.198 10 false MCMD 5.813,1.781 6.427,1.979 0.615,0.198 10 false SP+ 5.823,2.198 6.438,2.396 0.615,0.198 10 false SP- 5.802,2.583 6.417,2.781 0.615,0.198 10 false MICV 5.802,3 6.417,3.198 0.615,0.198 10 false MCVD 5.802,3.365 6.417,3.563 0.615,0.198 10 false MCI+ 5.813,3.771 6.427,3.969 0.615,0.198 10 false MCI- 5.781,4.792 6.552,5.198 0.771,0.406 10 false Telematics Transceiver 4.167,3.969 5.031,4.219 0.865,0.25 10 false (Shielded) 0.375,4.313 2.542,4.531 2.167,0.219 10 false Communication Telematics Box 2.698,1.292 3.313,1.49 0.615,0.198 10 false MCMD 2.833,1.698 3.448,1.896 0.615,0.198 10 false SP+ 2.865,2.094 3.479,2.292 0.615,0.198 10 false SP- 2.76,2.469 3.375,2.667 0.615,0.198 10 false MICV 2.802,2.865 3.417,3.063 0.615,0.198 10 false MIC1 2.792,3.271 3.406,3.469 0.615,0.198 10 false MIC2 2.802,3.667 3.417,3.865 0.615,0.198 10 false MCI- 2.031,1.292 2.375,1.51 0.344,0.219 10 false 1 2.042,1.688 2.365,1.906 0.323,0.219 10 false 3 2.031,2.083 2.417,2.281 0.385,0.198 10 false 8 2.031,2.469 2.458,2.688 0.427,0.219 10 false 5 2.031,2.865 2.396,3.083 0.365,0.219 10 false 2 2.031,3.26 2.333,3.458 0.302,0.198 10 false 7 2.01,3.656 2.271,3.875 0.26,0.219 10 false 4 3.219,1.281 3.833,1.479 0.615,0.198 10 false 1 3.219,1.677 3.833,1.875 0.615,0.198 10 false 3 3.219,2.083 3.833,2.281 0.615,0.198 10 false 9 3.219,2.479 3.833,2.677 0.615,0.198 10 false 6 3.198,2.875 3.813,3.073 0.615,0.198 10 false 10 3.208,3.26 3.823,3.458 0.615,0.198 10 false 11 3.229,3.677 3.844,3.875 0.615,0.198 10 false 5 5.552,1.688 6.167,1.885 0.615,0.198 10 false 20 5.542,1.302 6.156,1.5 0.615,0.198 10 false 14 5.552,2.083 6.167,2.281 0.615,0.198 10 false 21 5.552,2.479 6.167,2.677 0.615,0.198 10 false 31 5.552,2.875 6.177,3.073 0.625,0.198 10 false 33 5.552,3.271 6.177,3.469 0.625,0.198 10 false 34 5.563,3.667 6.188,3.865 0.625,0.198 10 false 35 5.781,4.604 6.323,4.802 0.542,0.198 10 false H10 0.26,4.844 1.031,5.25 0.771,0.406 10 false R17 5.802,4.208 6.417,4.406 0.615,0.198 10 false SGND 5.563,4.083 6.188,4.281 0.625,0.198 10 false 32 0.385,4.135 1,4.333 0.615,0.198 10 false P 0.26,5.021 2.427,5.24 2.167,0.219 10 false Map Light Assembly

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>REGISTRATION


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 10 seconds or more.


d.

Turn the GTS on.


e.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 233

f.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT TELEMATICS TRANSCEIVER
2.INSPECT TELEMATICS TRANSCEIVER
a.
B518361C02
1.385,1.833 1.604,1.313 false 0.823,1.615 1.26,1.313 false 0.083,0.094 0.438,0.385 0.354,0.292 10 false *a 0.531,1.635 1.063,1.875 0.531,0.24 10 false MCI- 1.031,1.865 1.563,2.104 0.531,0.24 10 false MICV
*a Component with harness connected
(Telematics Transceiver)


Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
31 (MICV) - Body ground Ignition switch ACC 4 to 6 V


Standard Resistance:
Tester Connection Condition Specified Condition
35 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY)

NG

6.REPLACE TELEMATICS TRANSCEIVER
3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY)
a.

Disconnect the H10 telematics transceiver connector.


b.

Disconnect the R17 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H10-14 (MCMD) - R17-1 (MCMD) Always Below 1 Ω
H10-20 (SP+) - R17-3 (SP+) Always Below 1 Ω
H10-21 (SP-) - R17-9 (SP-) Always Below 1 Ω
H10-31 (MICV) - R17-6 (MICV) Always Below 1 Ω
H10-33 (MCVD) - R17-10 (MIC1) Always Below 1 Ω
H10-34 (MCI+) - R17-11 (MIC2) Always Below 1 Ω
H10-35 (MCI-) - R17-5 (MCI-) Always Below 1 Ω
H10-14 (MCMD) or R17-1 (MCMD) - Body ground Always 10 kΩ or higher
H10-20 (SP+) or R17-3 (SP+) - Body ground Always 10 kΩ or higher
H10-21 (SP-) or R17-9 (SP-) - Body ground Always 10 kΩ or higher
H10-31 (MICV) or R17-6 (MICV) - Body ground Always 10 kΩ or higher
H10-33 (MCVD) or R17-10 (MIC1) - Body ground Always 10 kΩ or higher
H10-34 (MCI+) or R17-11 (MIC2) - Body ground Always 10 kΩ or higher
H10-35 (MCI-) or R17-5 (MCI-) - Body ground Always 10 kΩ or higher
H10-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAP LIGHT ASSEMBLY
a.
E409641C11
1.49,2.823 1.865,3.083 0.375,0.26 1.521,0.365 1.896,0.625 0.375,0.26 2.177,1.281 2.646,1.281 true 1.313,3.208 1.708,3.729 true 1.823,1.271 2.542,0.708 true 1.823,1.604 2.479,2.031 true 0.781,1.292 1.208,1.292 true 1.583,1.615 0.938,2.177 true 1.385,1.583 0.906,1.792 true 1.406,1.219 0.896,0.917 true 1,3.396 1.49,3.729 true 0.917,3.771 1.302,3.771 true 1.719,4 1.854,4.365 true 2.25,3.292 1.917,3.719 true 1.313,4.333 1.531,3.979 true 2.5,3.76 2.073,3.76 true 0.365,2.635 0.677,2.833 0.313,0.198 10 false *b 0.292,0.26 0.604,0.458 0.313,0.198 10 false *a 1.646,2.865 1.958,3.063 0.313,0.198 10 false P 1.583,0.417 1.896,0.615 0.313,0.198 10 false R17 2.688,1.208 3.271,1.583 0.583,0.375 10 false MCMD 0.448,3.688 1.031,4.063 0.583,0.375 10 false MCMD 2.583,0.625 3.167,1 0.583,0.375 10 false SP+ 2.531,1.969 3.115,2.344 0.583,0.375 10 false SP- 0.417,1.219 1,1.594 0.583,0.375 10 false MICV 0.552,1.729 1.052,2.083 0.5,0.354 10 false MIC2 0.563,0.823 1.146,1.198 0.583,0.375 10 false MCI- 0.604,2.167 1.188,2.542 0.583,0.375 10 false MIC1 1.063,3.063 1.646,3.438 0.583,0.375 10 false SP+ 0.563,3.313 1.146,3.688 0.583,0.375 10 false MIC1+ 1.896,4.323 2.531,4.656 0.635,0.333 10 false SP- 2.542,3.698 3.125,4.073 0.583,0.375 10 false MICV 0.927,4.313 1.427,4.667 0.5,0.354 10 false MIC2+ 2.229,3.135 2.813,3.51 0.583,0.375 10 false MCI-

Disconnect the R17 map light assembly connector.


b.

Disconnect the P communication telematics box connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R17-1 (MCMD) - P-1 (MCMD) Always Below 1 Ω
R17-3 (SP+) - P-3 (SP+) Always Below 1 Ω
R17-9 (SP-) - P-8 (SP-) Always Below 1 Ω
R17-6 (MICV) - P-5 (MICV) Always Below 1 Ω
R17-10 (MIC1) - P-2 (MIC1+) Always Below 1 Ω
R17-11 (MIC2) - P-7 (MIC2+) Always Below 1 Ω
R17-5 (MCI-) - P-4 (MCI-) Always Below 1 Ω
R17-1 (MCMD) or P-1 (MCMD) - Body ground Always 10 kΩ or higher
R17-3 (SP+) or P-3 (SP+) - Body ground Always 10 kΩ or higher
R17-9 (SP-) or P-8 (SP-) - Body ground Always 10 kΩ or higher
R17-6 (MICV) or P-5 (MICV) - Body ground Always 10 kΩ or higher
R17-10 (MIC1) or P-2 (MIC1+) - Body ground Always 10 kΩ or higher
R17-11 (MIC2) or P-7 (MIC2+) - Body ground Always 10 kΩ or higher
R17-5 (MCI-) or P-4 (MCI-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE COMMUNICATION TELEMATICS BOX

NG

REPLACE MAP LIGHT ASSEMBLY

5.REPLACE COMMUNICATION TELEMATICS BOX
a.

Replace the communication telematics box with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>COMMUNICATION TELEMATICS BOX>REMOVAL


b.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 233

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

6.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT