Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM
RM37A0E _59 Vehicle Exterior _086900 SLIDING ROOF / CONVERTIBLE _0420295 SLIDING ROOF SYSTEM C

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  B2341  Sensor (Motor) Failure  B2344  Position Failure  


DESCRIPTION

When the sliding roof ECU (sliding roof drive gear assembly) detects a motor malfunction and the sliding roof operation is stopped, DTC B2341 is stored.

When the sliding roof ECU (sliding roof drive gear assembly) detects a gear position malfunction and the sliding roof operation is stopped, DTC B2344 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2341 Sensor (Motor) Failure Sensor (motor) failure (The sliding roof ECU (sliding roof drive gear assembly) enters fail-safe mode due to a problem with the motor)
·

Sliding roof ECU (Sliding roof drive gear assembly)

·

Sliding roof switch (Map light assembly)

·

Wire harness or connector


B2344 Position Failure Position failure (The sliding roof ECU (sliding roof drive gear assembly) enters fail-safe mode due to a problem with the gear position)
·

Sliding roof ECU (Sliding roof drive gear assembly)

·

Sliding roof switch (Map light assembly)

·

Wire harness or connector



WIRING DIAGRAM

B567706E03
0.5,3.781 2.417,4.25 1.917,0.469 10 false Sliding Roof Switch (Map Light assembly) 4.521,5.177 6.458,5.542 1.938,0.365 10 false Sliding Roof ECU (Sliding Roof Drive Gear Assembly) 0.5,3.625 0.927,3.906 0.427,0.281 10 false R11 4.531,5.01 4.865,5.26 0.333,0.25 10 false R2 2.427,1.042 2.854,1.323 0.427,0.281 10 false 20 2.406,1.427 2.833,1.708 0.427,0.281 10 false 19 2.427,1.802 2.854,2.083 0.427,0.281 10 false 17 2.406,2.188 2.833,2.469 0.427,0.281 10 false 18 2.406,2.552 2.833,2.833 0.427,0.281 10 false 11 2.031,1.042 2.458,1.323 0.427,0.281 10 false OPN 2.052,1.427 2.479,1.708 0.427,0.281 10 false CLS 2.146,1.802 2.573,2.083 0.427,0.281 10 false UP 1.906,2.167 2.458,2.469 0.552,0.302 10 false DOWN 2.021,2.552 2.448,2.833 0.427,0.281 10 false GND 4.177,1.021 4.604,1.302 0.427,0.281 10 false 10 4.26,1.406 4.688,1.688 0.427,0.281 10 false 8 4.26,1.781 4.688,2.063 0.427,0.281 10 false 5 4.26,2.135 4.688,2.417 0.427,0.281 10 false 9 4.26,2.542 4.688,2.823 0.427,0.281 10 false 2 4.427,1.031 4.854,1.313 0.427,0.281 10 false OPN 4.417,1.781 4.844,2.063 0.427,0.281 10 false OPN 4.417,1.396 4.844,1.677 0.427,0.281 10 false CLS 4.427,2.167 4.854,2.448 0.427,0.281 10 false CLS 4.427,2.542 4.854,2.823 0.427,0.281 10 false E

CAUTION / NOTICE / HINT

NOTICE:

If the sliding roof ECU (sliding roof drive gear assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear assembly) must be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION



PROCEDURE

1.CHECK SLIDING ROOF OPERATION
a.

Check the sliding roof auto operation.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>OPERATION CHECK

OK:

Auto operation operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK DTC OUTPUT

NG

3.INITIALIZE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)
2.CHECK DTC OUTPUT
a.

Clear the DTCs.

Body Electrical > Sliding Roof > Clear DTCs
50002 147

b.

Check for DTCs.

Body Electrical > Sliding Roof > Trouble Codes
50001 147
OK:

DTCs B2341 and B2344 are not output.



Result:
Proceed to
OK
NG



OK

NG

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

3.INITIALIZE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)
a.

Check that the sliding roof ECU (sliding roof drive gear assembly) can be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

OK:

Sliding roof ECU (sliding roof drive gear assembly) can be initialized.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC OUTPUT

NG

5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY) AND BODY GROUND)
4.CHECK DTC OUTPUT
a.

Clear the DTCs.

Body Electrical > Sliding Roof > Clear DTCs
50002 147

b.

Check for DTCs.

Body Electrical > Sliding Roof > Trouble Codes
50001 147
OK:

DTCs B2341 and B2344 are not output.



Result:
Proceed to
OK
NG



OK

END (MALFUNCTION DUE TO INITIALIZATION FAILURE)

NG

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY) AND BODY GROUND)
a.

Disconnect the R11 sliding roof switch (map light assembly) connector.


b.

Disconnect the R2 sliding roof ECU (sliding roof drive gear assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R2-8 (CLS) - R11-19 (CLS) Always Below 1 Ω
R2-8 (CLS) or R11-19 (CLS) - Body ground Always 10 kΩ or higher
R2-10 (OPN) - R11-20 (OPN) Always Below 1 Ω
R2-10 (OPN) or R11-20 (OPN) - Body ground Always 10 kΩ or higher
R2-9 (CLS) - R11-18 (DOWN) Always Below 1 Ω
R2-9 (CLS) or R11-18 (DOWN) - Body ground Always 10 kΩ or higher
R2-5 (OPN) - R11-17 (UP) Always Below 1 Ω
R2-5 (OPN) or R11-17 (UP) - Body ground Always 10 kΩ or higher
R11-11 (GND) - Body ground Always Below 1 Ω
R2-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY)

OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

NG

REPLACE SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY)